Differences
This shows you the differences between the selected revision and the current version of the page.
dns-320 2011/01/23 16:39 | dns-320 2021/01/06 20:56 current | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== DNS-320 ====== | ====== DNS-320 ====== | ||
This page will share some more information about the [[http://www.dlink.co.uk/cs/Satellite?c=Product_C&childpagename=DLinkEurope-GB/DLProductCarouselMultiple&cid=1197388178398&p=1197318962342&packedargs=ProductParentID%3D1195808623796%26category%3DQuickProductFinder%26locale%3D1195806691854%26term%3DShareCenter%2BPulse%2B%2528DNS-320%2529&pagename=DLinkEurope-GB/DLWrapper|ShareCenter Pulse (DNS-320)]].\\ | This page will share some more information about the [[http://www.dlink.co.uk/cs/Satellite?c=Product_C&childpagename=DLinkEurope-GB/DLProductCarouselMultiple&cid=1197388178398&p=1197318962342&packedargs=ProductParentID%3D1195808623796%26category%3DQuickProductFinder%26locale%3D1195806691854%26term%3DShareCenter%2BPulse%2B%2528DNS-320%2529&pagename=DLinkEurope-GB/DLWrapper|ShareCenter Pulse (DNS-320)]].\\ | ||
- | \\ | ||
- | //Note: This page is in progress, as of today (November 22nd 2010) the device is still pretty new.// | ||
- | |||
- | |||
- | |||
- | |||
===== Hardware ===== | ===== Hardware ===== | ||
Line 15: | Line 9: | ||
^ USB | 1 USB2.0 Port (front) | | ^ USB | 1 USB2.0 Port (front) | | ||
^ LAN | Marvell 88E1118R-NNC1 | | ^ LAN | Marvell 88E1118R-NNC1 | | ||
- | ^ Cooling | Speed controlled 40mm fan ? (verifying) | | + | ^ Cooling | [[hardware:fan|ADDA AD045HB-G73]] | |
^ Kernel | 2.6.22.18 | | ^ Kernel | 2.6.22.18 | | ||
^ Samba | 3.2.8 | | ^ Samba | 3.2.8 | | ||
^ C library | gcc-4.2-glibc-2.5 | | ^ C library | gcc-4.2-glibc-2.5 | | ||
\\ | \\ | ||
+ | |||
+ | == Reviews & Tutorials == | ||
+ | |||
+ | * [[http://nas-tweaks.net/devices/d-link-dns-320/|DNS-320-Page on NAS-Tweaks with further Pictures]] | ||
+ | * [[http://jamie.lentin.co.uk/devices/dlink-dns325/|Replacing firmware with Debian Linux]] | ||
+ | |||
== /proc/cpuinfo == | == /proc/cpuinfo == | ||
<code>Processor : ARM926EJ-S rev 1 (v5l) | <code>Processor : ARM926EJ-S rev 1 (v5l) | ||
Line 47: | Line 47: | ||
</code> | </code> | ||
\\ | \\ | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ===== Serial PIN Layout ===== | ||
+ | |||
+ | BusyBox break-in code is 5784468 for Firmware before v2.03. Starting with v2.03 it is set by the ui [http://forums.dlink.com/index.php?topic=42483.msg149905#msg149905]. | ||
+ | |||
+ | Jumper: JP3\\ | ||
+ | TX [5]\\ | ||
+ | GND [4]\\ | ||
+ | VD33 [3]\\ | ||
+ | \\ | ||
+ | RX [1]\\ | ||
+ | \\ | ||
+ | |||
+ | ===== Serial console boot messages ===== | ||
+ | |||
+ | Below the messages sent to the serial console during the system startup, till init is started. | ||
+ | |||
+ | |||
+ | <code> | ||
+ | |||
+ | ** MARVELL BOARD: DB-88F6281A-BP LE | ||
+ | |||
+ | U-Boot 1.1.4 (Jun 7 2010 - 10:33:37) Marvell version: | ||
+ | 3.4.14.DNS320_02 | ||
+ | U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE80 | ||
+ | Soc: MV88F6281 Rev 3 (DDR2) | ||
+ | CPU running @ 800Mhz L2 running @ 400Mhz | ||
+ | SysClock = 200Mhz , TClock = 166Mhz | ||
+ | DRAM CAS Latency = 3 tRP = 3 tRAS = 8 tRCD=3 | ||
+ | DRAM CS[0] base 0x00000000 size 128MB | ||
+ | DRAM Total size 128MB 16bit width | ||
+ | Flash: 0 kB | ||
+ | Addresses 8M - 0M are saved for the U-Boot usage. | ||
+ | Mem malloc Initialization (8M - 7M): Done | ||
+ | NAND:128 MB | ||
+ | *** Warning - bad CRC or NAND, using default environment | ||
+ | CPU : Marvell Feroceon (Rev 1) | ||
+ | Streaming disabled | ||
+ | Write allocate disabled | ||
+ | USB 0: host mode | ||
+ | PEX 0: interface detected no Link. | ||
+ | Net: egiga0 [PRIME] | ||
+ | Hit any key to stop autoboot: 0 | ||
+ | NAND read: device 0 offset 0x100000, size 0x300000 | ||
+ | load addr .... =a00000 | ||
+ | 3145728 bytes read: OK | ||
+ | NAND read: device 0 offset 0x600000, size 0x300000 | ||
+ | load addr .... =f00000 | ||
+ | 3145728 bytes read: OK | ||
+ | ## Booting image at 00a00000 ... | ||
+ | Image Name: Linux-2.6.22.18 | ||
+ | Created: 2010-11-15 9:49:59 UTC | ||
+ | Image Type: ARM Linux Kernel Image (uncompressed) | ||
+ | Data Size: 2196588 Bytes = 2.1 MB | ||
+ | Load Address: 00008000 | ||
+ | Entry Point: 00008000 | ||
+ | Verifying Checksum ... OK | ||
+ | OK | ||
+ | ## Loading Ramdisk Image at 00f00000 ... | ||
+ | Image Name: Ramdisk | ||
+ | Created: 2010-12-06 7:00:10 UTC | ||
+ | Image Type: ARM Linux RAMDisk Image (gzip compressed) | ||
+ | Data Size: 1563868 Bytes = 1.5 MB | ||
+ | Load Address: 00e00000 | ||
+ | Entry Point: 00e00000 | ||
+ | Verifying Checksum ... OK | ||
+ | Starting kernel ... | ||
+ | |||
+ | Uncompressing Linux..................................................................................................................... | ||
+ | Linux version 2.6.22.18 (bing@SWTEST1) (gcc version 4.2.1) #22 Mon Nov 15 17:49:27 CST 2010 | ||
+ | CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053977 | ||
+ | Machine: Feroceon-KW | ||
+ | Using UBoot passing parameters structure | ||
+ | Memory policy: ECC disabled, Data cache writeback | ||
+ | CPU0: D VIVT write-back cache | ||
+ | CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets | ||
+ | CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets | ||
+ | Built 1 zonelists. Total pages: 32512 | ||
+ | Kernel command line: root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none | ||
+ | PID hash table entries: 512 (order: 9, 2048 bytes) | ||
+ | Console: colour dummy device 80x30 | ||
+ | Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) | ||
+ | Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) | ||
+ | Memory: 128MB 0MB 0MB 0MB = 128MB total | ||
+ | Memory: 123776KB available (4120K code, 251K data, 124K init) | ||
+ | Mount-cache hash table entries: 512 | ||
+ | CPU: Testing write buffer coherency: ok | ||
+ | NET: Registered protocol family 16 | ||
+ | |||
+ | CPU Interface | ||
+ | ------------- | ||
+ | SDRAM_CS0 ....base 00000000, size 128MB | ||
+ | SDRAM_CS1 ....disable | ||
+ | SDRAM_CS2 ....disable | ||
+ | SDRAM_CS3 ....disable | ||
+ | PEX0_MEM ....base e8000000, size 128MB | ||
+ | PEX0_IO ....base f2000000, size 1MB | ||
+ | INTER_REGS ....base f1000000, size 1MB | ||
+ | NFLASH_CS ....base fa000000, size 2MB | ||
+ | SPI_CS ....base f4000000, size 16MB | ||
+ | BOOT_ROM_CS ....no such | ||
+ | DEV_BOOTCS ....no such | ||
+ | CRYPT_ENG ....base f0000000, size 2MB | ||
+ | |||
+ | Marvell Development Board (LSP Version KW_LSP_4.3.4_patch30)-- DB-88F6281A-BP Soc: 88F6281 A1 LE | ||
+ | |||
+ | Detected Tclk 166666667 and SysClk 200000000 | ||
+ | MV Buttons Device Load | ||
+ | Marvell USB EHCI Host controller #0: c05bb600 | ||
+ | PEX0 interface detected no Link. | ||
+ | PCI: bus0: Fast back to back transfers enabled | ||
+ | SCSI subsystem initialized | ||
+ | usbcore: registered new interface driver usbfs | ||
+ | usbcore: registered new interface driver hub | ||
+ | usbcore: registered new device driver usb | ||
+ | NET: Registered protocol family 2 | ||
+ | Time: kw_clocksource clocksource has been installed. | ||
+ | IP route cache hash table entries: 1024 (order: 0, 4096 bytes) | ||
+ | TCP established hash table entries: 4096 (order: 3, 32768 bytes) | ||
+ | TCP bind hash table entries: 4096 (order: 2, 16384 bytes) | ||
+ | TCP: Hash tables configured (established 4096 bind 4096) | ||
+ | TCP reno registered | ||
+ | checking if image is initramfs...it isn't (no cpio magic); looks like an initrd | ||
+ | Freeing initrd memory: 1527K | ||
+ | cpufreq: Init kirkwood cpufreq driver | ||
+ | XOR registered 1 NET_DMA over 4 channels | ||
+ | XOR 2nd invalidate WA enabled | ||
+ | cesadev_init(c00119d8) | ||
+ | mvCesaInit: sessions=640, queue=64, pSram=f0000000 | ||
+ | Warning: TS unit is powered off. | ||
+ | MV Buttons Driver Load | ||
+ | VFS: Disk quotas dquot_6.5.1 | ||
+ | Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) | ||
+ | squashfs: version 3.3 (2007/10/31) Phillip Lougher | ||
+ | squashfs: LZMA suppport for slax.org by jro | ||
+ | Installing knfsd (copyright (C) 1996 okir@monad.swb.de). | ||
+ | JFFS2 version 2.2. (NAND) �Â�© 2001-2006 Red Hat, Inc. | ||
+ | SGI XFS with large block numbers, no debug enabled | ||
+ | io scheduler noop registered | ||
+ | io scheduler anticipatory registered (default) | ||
+ | Serial: 8250/16550 driver $Revision: 1.7 $ 4 ports, IRQ sharing disabled | ||
+ | serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A | ||
+ | serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A | ||
+ | RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize | ||
+ | loop: module loaded | ||
+ | Loading Marvell Ethernet Driver: | ||
+ | o Cached descriptors in DRAM | ||
+ | o DRAM SW cache-coherency | ||
+ | o Single RX Queue support - ETH_DEF_RXQ=0 | ||
+ | o Single TX Queue support - ETH_DEF_TXQ=0 | ||
+ | o TCP segmentation offload enabled | ||
+ | o LRO support supported | ||
+ | o Receive checksum offload enabled | ||
+ | o Transmit checksum offload enabled | ||
+ | o Network Fast Processing (Routing) supported | ||
+ | o Driver ERROR statistics enabled | ||
+ | o Driver INFO statistics enabled | ||
+ | o Proc tool API enabled | ||
+ | o SKB Reuse supported | ||
+ | o SKB Recycle supported | ||
+ | o Rx descripors: q0=128 | ||
+ | o Tx descripors: q0=532 | ||
+ | o Loading network interface(s): | ||
+ | o register under egiga0 platform | ||
+ | o egiga0, ifindex = 1, GbE port = 0 | ||
+ | |||
+ | Warning: Giga 1 is Powered Off | ||
+ | |||
+ | mvFpRuleDb (c7dd0000): 1024 entries, 4096 bytes | ||
+ | Integrated Sata device found | ||
+ | scsi0 : Marvell SCSI to SATA adapter | ||
+ | scsi1 : Marvell SCSI to SATA adapter | ||
+ | scsi 0:0:0:0: Direct-Access SAMSUNG HD502IJ 1AA0 PQ: 0 ANSI: 5 | ||
+ | scsi 1:0:0:0: Direct-Access SAMSUNG HD502IJ 1AA0 PQ: 0 ANSI: 5 | ||
+ | scsi 0:0:0:0: Attached scsi generic sg0 type 0 | ||
+ | scsi 1:0:0:0: Attached scsi generic sg1 type 0 | ||
+ | NFTL driver: nftlcore.c $Revision: 1.1.1.1 $, nftlmount.c $Revision: 1.1.1.1 $ | ||
+ | NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit) | ||
+ | Scanning device for bad blocks | ||
+ | Bad eraseblock 98 at 0x00c40000 | ||
+ | Using static partition definition | ||
+ | Creating 6 MTD partitions on "nand_mtd": | ||
+ | 0x00000000-0x00100000 : "u-boot" | ||
+ | 0x00100000-0x00600000 : "uImage" | ||
+ | 0x00600000-0x00b00000 : "ramdisk" | ||
+ | 0x00b00000-0x07100000 : "image" | ||
+ | 0x07100000-0x07b00000 : "mini firmware" | ||
+ | 0x07b00000-0x08000000 : "config" | ||
+ | ehci_marvell ehci_marvell.70059: Marvell Orion EHCI | ||
+ | ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 | ||
+ | ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 | ||
+ | ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 | ||
+ | usb usb1: configuration #1 chosen from 1 choice | ||
+ | hub 1-0:1.0: USB hub found | ||
+ | hub 1-0:1.0: 1 port detected | ||
+ | USB Universal Host Controller Interface driver v3.0 | ||
+ | mice: PS/2 mouse device common for all mice | ||
+ | i2c /dev entries driver | ||
+ | md: linear personality registered for level -1 | ||
+ | md: raid0 personality registered for level 0 | ||
+ | md: raid1 personality registered for level 1 | ||
+ | device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com | ||
+ | dm_crypt using the OCF package. | ||
+ | usbcore: registered new interface driver usbhid | ||
+ | drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver | ||
+ | TCP cubic registered | ||
+ | NET: Registered protocol family 1 | ||
+ | NET: Registered protocol family 17 | ||
+ | md: Autodetecting RAID arrays. | ||
+ | md: autorun ... | ||
+ | md: ... autorun DONE. | ||
+ | RAMDISK: Compressed image found at block 0 | ||
+ | VFS: Mounted root (ext2 filesystem). | ||
+ | Freeing init memory: 124K | ||
+ | init started: BusyBox v1.11.2 (2010-11-17 11:44:30 CST) | ||
+ | [...] | ||
+ | </code> | ||
+ | |||
===== Setting up ffp ===== | ===== Setting up ffp ===== | ||
- | To get the [[http://wiki.dns323.info/howto:ffp|fonz fun_plug]] running some small changes to the available ffp ''fun_plug'' file are needed. | + | There is a complete Tutorial on the Installation of ffp available on NAS-Tweaks: [[http://nas-tweaks.net/40/installation-of-the-fonz-funplug-0-5-for-ch3snas-ch3mnas-dns-323-and-many-more/|Installation of fun_plug 0.5]]. If you want to do everything yourself instead, just follow the instructions below. |
+ | |||
+ | To get the [[howto:ffp|fonz fun_plug]] running some small changes to the available ffp ''fun_plug'' file are needed. | ||
Search and replace all entries of ''/mnt/HD_a2/'' with ''/mnt/HD/HD_a2/''.\\ | Search and replace all entries of ''/mnt/HD_a2/'' with ''/mnt/HD/HD_a2/''.\\ | ||
+ | \\ | ||
Then follow the normal instructions of how to install ffp.\\ | Then follow the normal instructions of how to install ffp.\\ | ||
\\ | \\ | ||
+ | shadowandy has provided modified ffp package for DNS-320 [[http://www.shadowandy.net/2010/11/dns-320-making-fun_plug-and-old-packages-work.htm|here]] | ||
+ | \\ | ||
+ | \\ | ||
+ | Another article in German on installing fun_plug 0.5 can be found [[http://wolf-u.li/3779/installation-des-fonz-fun_plug-0-5-auf-dem-d-link-dns-320-sharecenter-pulse/|here]] | ||
+ | \\ | ||
+ | \\ | ||
+ | |||
Once installed and running you might want to set-up ssh and change the root password. ([[http://nas-tweaks.net/CH3SNAS:Tutorials/fun_plug#Change_root_password|for example this]])\\ | Once installed and running you might want to set-up ssh and change the root password. ([[http://nas-tweaks.net/CH3SNAS:Tutorials/fun_plug#Change_root_password|for example this]])\\ | ||
Line 68: | Line 300: | ||
cp -f /etc/samba/smbpasswd /usr/local/config/. | cp -f /etc/samba/smbpasswd /usr/local/config/. | ||
</code> | </code> | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ===== Installation and Configuration of Transmission with addons ===== | ||
+ | Contributed by [[Zane Chua]] on 10th June 2011. | ||
+ | \\ | ||
+ | \\ | ||
+ | First of all, you need Funplug 0.5 above. | ||
+ | SSH into the NAS by using PuTTY. | ||
+ | Installation of Transmission: | ||
+ | <code> | ||
+ | wget http://kylek.is-a-geek.org:31337/files/curl-7.18.1.tgz | ||
+ | wget http://kylek.is-a-geek.org:31337/files/Transmission-2.42-1.tgz | ||
+ | funpkg -i curl-7.18.1.tgz | ||
+ | funpkg -i Transmission-2.42-1.tgz | ||
+ | </code> | ||
+ | \\ | ||
+ | Once installed, you need to edit the transmission.sh in /ffp/start | ||
+ | SSH into the NAS by using PuTTY again. | ||
+ | Type these commands: | ||
+ | <code> | ||
+ | wget http://ffp.wolf-u.li/additional/app-editors/nano-2.0.9-2.tgz | ||
+ | funpkg -i nano-2.0.9-2.tgz | ||
+ | cd /ffp/start/ | ||
+ | nano transmission.sh | ||
+ | </code> | ||
+ | Edit the line from | ||
+ | <code> | ||
+ | TRANSMISSION_HOME=/mnt/HD_a2/.transmission-daemon | ||
+ | </code> | ||
+ | to | ||
+ | <code> | ||
+ | TRANSMISSION_HOME=/mnt/HD/HD_a2/.transmission-daemon | ||
+ | </code> | ||
+ | Press Ctrl + O and Ctrl + X | ||
+ | \\ | ||
+ | After that, i believe that you would want to access the Transmission Web Interface. | ||
+ | \\ | ||
+ | SSH into the NAS by using PuTTY again. | ||
+ | <code> | ||
+ | /ffp/start/transmission.sh stop | ||
+ | su nobody -c "transmission-daemon -f -g /mnt/HD/HD_a2/.transmission-daemon -w /mnt/HD/HD_a2/Downloads -a 127.0.0.1,192.168.1.*" | ||
+ | </code> | ||
+ | \\ | ||
+ | I downloaded Transmission Torrent Client Utilities v0.2 from http://dns323.thecorewithin.net/ | ||
+ | \\ | ||
+ | Run this code via SSH again | ||
+ | <code> | ||
+ | wget http://dns323.thecorewithin.net/trans_utils-0.2.tgz | ||
+ | mv trans_utils-0.2.tgz /mnt/HD/HD_a2/trans_utils-0.2.tgz | ||
+ | cd /mnt/HD/HD_a2/ | ||
+ | tar xvzf trans_utils-0.2.tgz | ||
+ | cd trans_utils-0.2 | ||
+ | nano install.sh | ||
+ | </code> | ||
+ | Change the line from | ||
+ | <code> | ||
+ | BASE_SHARE=/mnt/HD_a2 | ||
+ | </code> | ||
+ | to | ||
+ | <code> | ||
+ | BASE_SHARE=/mnt/HD/HD_a2 | ||
+ | </code> | ||
+ | Press Ctrl + O and Ctrl + X | ||
+ | \\ | ||
+ | \\ | ||
+ | Continue with the code: | ||
+ | <code> | ||
+ | cd scripts | ||
+ | nano torrent_utils.sh | ||
+ | </code> | ||
+ | Change the line from | ||
+ | <code> | ||
+ | BASE_SHARE=/mnt/HD_a2 | ||
+ | </code> | ||
+ | to | ||
+ | <code> | ||
+ | BASE_SHARE=/mnt/HD/HD_a2 | ||
+ | </code> | ||
+ | and the line from | ||
+ | <code> | ||
+ | TRANSMISSION_HOME=/mnt/HD_a2/.transmission-daemon | ||
+ | </code> | ||
+ | to | ||
+ | <code> | ||
+ | TRANSMISSION_HOME=/mnt/HD/HD_a2/.transmission-daemon | ||
+ | </code> | ||
+ | and the line from | ||
+ | <code> | ||
+ | WATCH_DIR=$BASE_SHARE/watch | ||
+ | </code> | ||
+ | to | ||
+ | <code> | ||
+ | WATCH_DIR=$BASE_SHARE/Downloads/watch | ||
+ | </code> | ||
+ | and the line from | ||
+ | <code> | ||
+ | COMPLETE_DIR=$BASE_SHARE/complete | ||
+ | </code> | ||
+ | to | ||
+ | <code> | ||
+ | COMPLETE_DIR=$BASE_SHARE/Downloads | ||
+ | </code> | ||
+ | Search for the line | ||
+ | <code> | ||
+ | mv "$COMPLETE_DIR/${SEEDING_FILENAME}.moving" "$COMPLETE_DIR/${SEEDING_FILENAME}" | ||
+ | </code> | ||
+ | Add this line below it | ||
+ | <code> | ||
+ | chown -R *USERNAME* "$COMPLETE_DIR/${SEEDING_FILENAME}" | ||
+ | </code> | ||
+ | Replace *USERNAME* with a User you created in the Web Configuration so anyone can edit the files | ||
+ | \\ | ||
+ | Press Ctrl + O and Ctrl + X | ||
+ | \\ | ||
+ | \\ | ||
+ | Continue with the code: | ||
+ | <code> | ||
+ | cd .. | ||
+ | cd start | ||
+ | nano trans_utils.sh | ||
+ | </code> | ||
+ | \\ | ||
+ | Change the line from | ||
+ | <code> | ||
+ | TRAN_UTILS=/mnt/HD_a2/.transmission-daemon/scripts | ||
+ | </code> | ||
+ | to | ||
+ | <code> | ||
+ | TRAN_UTILS=/mnt/HD/HD_a2/.transmission-daemon/scripts | ||
+ | </code> | ||
+ | \\ | ||
+ | Continue with the code: | ||
+ | <code> | ||
+ | cd .. | ||
+ | ./install.sh | ||
+ | </code> | ||
+ | It shouldn't have any issues running but it should make a watch and complete folder in /mnt/HD/HD_a2 which is not even used so we shall just remove them and create them in the proper directories | ||
+ | \\ | ||
+ | Continue with the code: | ||
+ | <code> | ||
+ | cd .. | ||
+ | rm -rf watch | ||
+ | rm -rf complete | ||
+ | cd Downloads | ||
+ | mkdir watch | ||
+ | cd .. | ||
+ | /ffp/start/transmission.sh stop (wait a while after this) | ||
+ | chown -R nobody /mnt/HD/HD_a2/.transmission-daemon | ||
+ | chown -R nobody /mnt/HD/HD_a2/Downloads | ||
+ | </code> | ||
+ | \\ | ||
+ | **Extras** | ||
+ | \\ | ||
+ | If you're a paranoid freak like me and you want to be able to remote access your DNS-320 not from your home and want to use a different port. | ||
+ | \\ | ||
+ | You have to change the line in torrent_utils.sh from | ||
+ | \\ | ||
+ | <code> | ||
+ | TRANS_REMOTE=$BASE_SYS/bin/transmission-remote | ||
+ | </code> | ||
+ | to | ||
+ | <code> | ||
+ | TRANS_REMOTE="$BASE_SYS/bin/transmission-remote Port" | ||
+ | </code> | ||
+ | \\ | ||
+ | and then if you're intending to use authentication by username and password you have to add the username and password in the respective fields in the Settings.json File located in /mnt/HD/HD_a2/.transmission-daemon. | ||
+ | \\ | ||
+ | Then you have to change the line in torrent_utils.sh from | ||
+ | \\ | ||
+ | <code> | ||
+ | TRANS_REMOTE=$BASE_SYS/bin/transmission-remote | ||
+ | </code> | ||
+ | to | ||
+ | <code> | ||
+ | TRANS_REMOTE="$BASE_SYS/bin/transmission-remote port --auth username:password" | ||
+ | </code> | ||
+ | That should work. Theoretically. If something is wrong with my commands, can someone please edit. | ||
+ | \\ | ||
+ | Configuration of Automatic. | ||
+ | \\ | ||
+ | I just recently decided to test out Automatic again, i had issues the last time but it seems everything works perfectly now so i'm including this here. | ||
+ | \\ | ||
+ | SSH into your NAS via PuTTY and make sure you're in /mnt/HD/HD_a2 | ||
+ | <code> | ||
+ | wget http://kylek.is-a-geek.org:31337/files/Automatic-0.7.1-1.tgz | ||
+ | wget http://www.inreto.de/dns323/fun-plug/0.5/packages/libxml2-2.6.31-2.tgz | ||
+ | wget http://www.inreto.de/dns323/fun-plug/0.5/packages/pcre-7.7-1.tgz | ||
+ | funpkg -i libxml2-2.6.31-2.tgz | ||
+ | funpkg -i pcre-7.7-1.tgz | ||
+ | funpkg -i Automatic-0.7.1-1.tgz | ||
+ | </code> | ||
+ | \\ | ||
+ | You then need to edit the automatic.sh located in /ffp/start. | ||
+ | <code> | ||
+ | cd /ffp/start/ | ||
+ | nano automatic.sh | ||
+ | </code> | ||
+ | Edit the line from | ||
+ | <code> | ||
+ | automatic_flags="-c /ffp/etc/automatic.conf -l /mnt/HD_a2/.transmission-daemon/automatic.log" | ||
+ | </code> | ||
+ | to | ||
+ | <code> | ||
+ | automatic_flags="-c /ffp/etc/automatic.conf -l /mnt/HD/HD_a2/.transmission-daemon/automatic.log -v 2" | ||
+ | </code> | ||
+ | Press Ctrl + O and Ctrl + X | ||
+ | \\ | ||
+ | \\ | ||
+ | Now you need to create a automatic configuration file. We'll use the sample file. | ||
+ | <code> | ||
+ | cd /ffp/etc/ | ||
+ | nano automatic.conf-sample | ||
+ | </code> | ||
+ | Remove the # from rpc-host and rpc-port. | ||
+ | \\ | ||
+ | If you need #rpc-auth means you've configured a username and password for Transmission. | ||
+ | \\ | ||
+ | Change the line from | ||
+ | <code> | ||
+ | torrent-folder = "/tmp" | ||
+ | </code> | ||
+ | to | ||
+ | <code> | ||
+ | torrent-folder = "/mnt/HD/HD_a2/.transmission-daemon/autotorrents" | ||
+ | </code> | ||
+ | and the line from | ||
+ | <code> | ||
+ | statefile = "~/.config/automatic.state" | ||
+ | </code> | ||
+ | to | ||
+ | <code> | ||
+ | statefile = "/mnt/HD/HD_a2/.transmission-daemon/automatic.state" | ||
+ | </code> | ||
+ | Edit in your RSS Feeds and filters | ||
+ | \\ | ||
+ | Press Ctrl + O when you're done and save it as automatic.conf | ||
+ | then Press Ctrl + X | ||
+ | \\ | ||
+ | Now we need to go create the folders and state file for automatic. Fire up PuTTY again and do these commands: | ||
+ | <code> | ||
+ | cd /mnt/HD/HD_a2/.transmission-daemon | ||
+ | mkdir autotorrents | ||
+ | touch automatic.state | ||
+ | chmod 777 automatic.state | ||
+ | </code> | ||
+ | \\ | ||
+ | Now you can start automatic.sh by typing | ||
+ | <code> | ||
+ | /ffp/start/automatic.sh start | ||
+ | </code> | ||
+ | If you want to stop automatic | ||
+ | <code> | ||
+ | /ffp/start/automatic.sh stop | ||
+ | </code> | ||
+ | \\ | ||
+ | Just some tips for the Filters. My RSS Feeds are basically sorted out so I used this section for filters | ||
+ | <code> | ||
+ | filter = { pattern => "(?!.*.)" | ||
+ | } | ||
+ | </code> | ||
+ | It basically means that it applies to all RSS Feeds. | ||
+ | \\ | ||
+ | All my commands should be correct, someone edit em if they're wrong. Have fun! | ||
+ | |||
+ | ===== Changing the port of Web Configuration Utility ===== | ||
+ | \\ | ||
+ | Contributed by [[mailto:kothapet@Hotmail.com|Anand Kothapeta]] on 5/20/2011. | ||
+ | \\ | ||
+ | \\ | ||
+ | I was running two NAS servers (one D-Link DNS-320 and my old PC with FreeNAS) and a web server on a different PC. These are all behind my router. My router and FreeNAS allows me to change the default port for the web configuration utilities. So, I can change them from port 80 and port forward them, and can access the web configuration utilities from internet. However I always have an issue with DNS-320, since it doesn't allow me to change the port and it conflicts with web server. There are some articles on how to change it by running lighttpd. However, I found out that DNS-320 also uses the lighttpd to run the webconfig utility. Also those articles change the port to 81 (not much flexibility). I finally figured out a way to change the port to whatever I wish it to be. Here are the steps. You need to first install the ffp using above articles and links. | ||
+ | \\ | ||
+ | \\ | ||
+ | 1) telnet/ssh login to the DNS-320 box. (see ffp tutorials) and run the following command | ||
+ | <code> | ||
+ | cp /etc/lighttpd/lighttpd.conf /ffp/lighttpd_portmod.conf | ||
+ | </code> | ||
+ | \\ | ||
+ | 2) Now edit the /ffp/lighttpd_portmod.conf file and change the following line to lets say 8888 and save the file. | ||
+ | <code> | ||
+ | server.port = 8888 | ||
+ | </code> | ||
+ | \\ | ||
+ | 3) edit the fun_plug script and add the following lines between fun_plug.local and FFP_RC if conditions. | ||
+ | <code> | ||
+ | # run fun_plug.local, if present | ||
+ | if [ -x /ffp/etc/fun_plug.local ]; then | ||
+ | echo "* Running /ffp/etc/fun_plug.local ..." | ||
+ | /ffp/etc/fun_plug.local | ||
+ | fi | ||
+ | |||
+ | #*** start Mods for different http port for webadmin tool | ||
+ | echo "killing lighttpd-angel" | ||
+ | kill -9 `pidof lighttpd-angel` | ||
+ | echo "killing lighttpd" | ||
+ | kill -9 `pidof lighttpd` | ||
+ | |||
+ | echo "Restart lighttpd-angel with different port" | ||
+ | /usr/sbin/lighttpd-angel -D -m /usr/local/lib -f /ffp/lighttpd_portmod.conf & | ||
+ | #*** end Mods different http port | ||
+ | |||
+ | # run commands | ||
+ | if [ -x $FFP_RC ]; then | ||
+ | echo "* Running $FFP_RC ..." | ||
+ | $FFP_RC | ||
+ | echo "* OK" | ||
+ | else | ||
+ | echo "$FFP_RC: Not found or not executable" | ||
+ | fi | ||
+ | </code> | ||
+ | \\ | ||
+ | 4) Now reboot it. | ||
+ | \\ | ||
+ | \\ | ||
+ | 5) Look at ffp.log to make sure you see the following lines. | ||
+ | <code> | ||
+ | killing lighttpd-angel | ||
+ | killing lighttpd | ||
+ | Restart lighttpd-angel with different port | ||
+ | </code> | ||
+ | \\ | ||
+ | 6) Now open the browser and try http://<ipaddress>:8888/ should take you to the web config tool. | ||
+ | \\ | ||
+ | \\ | ||
+ | 7) Now you can port forward 8888 in your router, and port forward 80 to web server. | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ===== Setting up Debian in chrooted enviroment ===== | ||
+ | D-Link put a prebuilt Debian Squeeze package on their [[ftp://ftp.dlink.pl/dns/dns-320/driver_software/DNS-320%26325_linuxDebian_revA_Squeeze_all_en_20110111.zip|ftp]] site, in 2011. The package size is approximately 150 MB. Read the instruction inside. You may have to modify ''--bind'' (dash-dash-bind) to ''--rbind'' (dash-dash-rbind) for the ''/proc'' (and possibly ''/dev'') mounts in fun_plug.debian to get some usb devices (e.g. the DS9490R USB-1wire adapter) to work properly in squeeze. | ||
+ | |||
+ | The prebuilt Debian Squeeze package is NO LONGER available through the D-Link FTP, as of july 2014, but a backup is listed on this [[https://code.google.com/archive/p/funplug-dns320-dns325/downloads|Google Code]] page. | ||
+ | |||
+ | ===== Source code for firmware ==== | ||
+ | Dlink have release source code for firmware 1.0 on their [[ftp://ftp.dlink.fr/DNS/DNS-320/GPL/dns-320_a1_fw_v1.00_gpl(0216101012).tgz|ftp]] site. The source code size is approximate 25 MB | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ===== U-BOOT Configuration ==== | ||
+ | You can access the boot console (for trying to run your own kernel) via a netconsole. | ||
+ | To interrupt the U-Boot startup, press SPACE and 1 before the one-second timeout. You should get a Marvell_DNS320>> prompt immediately. If the kernel starts to boot, you missed the timeout window. Starting ahead of the timeout and pressing SPACE-1-SPACE-1, etc. will increase you chances of hitting the window. | ||
+ | |||
+ | The full U-Boot environment (MAC addresses hidden) is: | ||
+ | <code> | ||
+ | Marvell_DNS320>> printenv | ||
+ | bootargs=root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none | ||
+ | bootcmd=nand read.e 0xa00000 0x100000 0x300000;nand read.e 0xf00000 0x600000 0x300000;bootm 0xa00000 0xf00000 | ||
+ | baudrate=115200 | ||
+ | loads_echo=0 | ||
+ | ipaddr=2.76.88.201 | ||
+ | serverip=2.76.88.2 | ||
+ | rootpath=/mnt/ARM_FS/ | ||
+ | netmask=255.255.255.0 | ||
+ | stdin=serial | ||
+ | stdout=serial | ||
+ | stderr=serial | ||
+ | console=console=ttyS0,115200 mtdparts=nand_mtd:0xc0000@0(uboot)ro,0x7f00000@0x100000(root) | ||
+ | mainlineLinux=no | ||
+ | CASset=min | ||
+ | enaMonExt=no | ||
+ | enaCpuStream=no | ||
+ | enaWrAllo=no | ||
+ | pexMode=RC | ||
+ | disL2Cache=no | ||
+ | setL2CacheWT=yes | ||
+ | disL2Prefetch=yes | ||
+ | enaICPref=yes | ||
+ | enaDCPref=yes | ||
+ | sata_dma_mode=yes | ||
+ | MALLOC_len=1 | ||
+ | ethprime=egiga0 | ||
+ | netbsd_en=no | ||
+ | vxworks_en=no | ||
+ | bootargs_root=root=/dev/nfs rw | ||
+ | bootargs_end=:::DB88FXX81:eth0:none | ||
+ | image_name=uImage | ||
+ | standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(m; | ||
+ | bootdelay=1 | ||
+ | disaMvPnp=no | ||
+ | ethaddr=00:50:XX:XX:XX:XX | ||
+ | ethmtu=1500 | ||
+ | mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs | ||
+ | mvNetConfig=mv_net_config=(00:11:XX:XX:XX:XX,0:1:2:3),mtu=1500 | ||
+ | usb0Mode=host | ||
+ | yuk_ethaddr=00:00:00:XX:XX:XX | ||
+ | nandEcc=1bit | ||
+ | netretry=no | ||
+ | rcvrip=169.254.100.100 | ||
+ | loadaddr=0x02000000 | ||
+ | autoload=no | ||
+ | enaAutoRecovery=yes | ||
+ | ethact=egiga0 | ||
+ | |||
+ | Environment size: 1238/131068 bytes | ||
+ | </code> | ||
+ | |||
+ | |||
+ | ===== Building a Custom Firmware ("ROM") ===== | ||
+ | D-Link provides a complete build environment on its [[ftp://ftp.dlink.de/dns/dns-320/driver_software/DNS-320_GPL_code_revA.tgz|ftp server]] that lets you create your own firmware images easily. Untar it and run | ||
+ | <code> source build_fw </code> | ||
+ | this will result in a file "DNS320-firmware" in the merge folder, which can be flashed to the unit via the webinterface (firmware update). | ||
+ | Right now the build_fw script does not do a full rebuild of the complete firmware, it rather puts together precompiled binaries that come with the built environment. [[http://dns323.kood.org/forum/viewtopic.php?pid=41860#p41860|Here]] is an attempt at rebuilding the build script. [[http://curvedbrain.org/2008/06/09/building-firmware-binary-image-d-link-dns-323/|This]] blog post describes how to assemble a firmware image for the [[http://wiki.dns323.info/start|DNS-323]] and will probably helpful for the DNS-320 as well. | ||
+ | |||
+ | Use this custom build_fw to make a custom settings for the kernel | ||
+ | <code> | ||
+ | # Dlink build envorment it only works on x86 arch (32Bits) | ||
+ | |||
+ | if [ ! -d "arm-none-linux-gnueabi-6xxx" ]; then | ||
+ | # directory did not exists unpack it | ||
+ | tar zxvf arm-none-linux-gnueabi-6xxx.tgz | ||
+ | fi | ||
+ | |||
+ | WORKDIR=$(pwd) | ||
+ | export WORKDIR | ||
+ | PATH=${WORKDIR}/arm-none-linux-gnueabi-6xxx/bin:$PATH | ||
+ | export PATH | ||
+ | CC=arm-none-linux-gnueabi-gcc | ||
+ | export CC | ||
+ | export CROSS_COMPILE=arm-none-linux-gnueabi- | ||
+ | CXX=${CROSS_COMPILE}g++ | ||
+ | export CXX | ||
+ | RANLIB=arm-none-linux-gnueabi-ranlib | ||
+ | export RANLIB | ||
+ | LD=arm-none-linux-gnueabi-ld | ||
+ | export LD | ||
+ | STRIP=arm-none-linux-gnueabi-strip | ||
+ | export STRIP | ||
+ | |||
+ | # gl setup path to mkimage | ||
+ | if [ ! -d "ramdisk" ]; then | ||
+ | tar -xzf ramdisk.tgz | ||
+ | fi | ||
+ | PATH=${WORKDIR}/ramdisk:$PATH | ||
+ | |||
+ | # gl extract kernel | ||
+ | if [ ! -d "linux-2.5.22.18" ]; then | ||
+ | tar -xzf linux-2.6.22.18.tgz | ||
+ | fi | ||
+ | |||
+ | # config our kernel and build it | ||
+ | cd ./linux-2.6.22.18 | ||
+ | sh cv.sh | ||
+ | make clean | ||
+ | make menuconfig | ||
+ | make | ||
+ | make modules | ||
+ | make uImage | ||
+ | cd ../ | ||
+ | |||
+ | # Dlink run merge now | ||
+ | if [ ! -d "merge" ]; then | ||
+ | tar zxvf merge.tgz | ||
+ | fi | ||
+ | |||
+ | if [ ! -f "merge/uImage.org" ]; then | ||
+ | mv merge/uImage merge/uImage.org | ||
+ | fi | ||
+ | |||
+ | if [ -f "merge/uImage" ]; then | ||
+ | rm merge/uImage | ||
+ | fi | ||
+ | |||
+ | cp linux-2.6.22.18/arch/arm/boot/uImage merge/uImage | ||
+ | cd merge | ||
+ | sudo cp ../ramdisk/uRamdisk . | ||
+ | ./merge | ||
+ | </code> | ||
+ | |||
+ | This Program works simlure as Dlink 320 merge does. It have been create by Magnus Olsen and release under GPL 2.0 | ||
+ | The header for firmware are lite diffent againts DNS-323 | ||
+ | to use it as merge u need compile it | ||
+ | gcc dns320flash.c -o dns320flash | ||
+ | copy where merge is and type dns320flash -mf myDNS320firmware | ||
+ | now u will have a firmware call myDNS320firmware | ||
+ | |||
+ | |||
+ | <code> | ||
+ | |||
+ | #include <stdio.h> | ||
+ | #include <stdlib.h> | ||
+ | |||
+ | #define UINT32 unsigned int | ||
+ | #define BYTE unsigned char | ||
+ | #define ALGIN4(_x) (_x + (4 - (_x % 4))) | ||
+ | typedef struct { | ||
+ | UINT32 uImageOffset; | ||
+ | UINT32 uImageLenght; | ||
+ | UINT32 uRamDiskOffset; | ||
+ | UINT32 uRamDiskLenght; | ||
+ | UINT32 ImageOffset; | ||
+ | UINT32 ImageLenght; | ||
+ | UINT32 DefaultOffset; | ||
+ | UINT32 DefaultLenght; | ||
+ | UINT32 uImageChecksum; | ||
+ | UINT32 uRamDiskChecksum; | ||
+ | UINT32 ImageChecksum; | ||
+ | UINT32 DefaultChecksum; | ||
+ | BYTE magic_0; | ||
+ | BYTE magic_1; | ||
+ | BYTE strModelName[9]; | ||
+ | BYTE magic_2; | ||
+ | BYTE productId; | ||
+ | BYTE customId; | ||
+ | BYTE modelId; | ||
+ | BYTE hardwareId; | ||
+ | BYTE subId; | ||
+ | BYTE Reseverd[59]; | ||
+ | UINT32 NextOffset; | ||
+ | } DLINK_DNS320_FIRMWARE_HEAD_128BYTE; | ||
+ | |||
+ | void showFirmware(char *flashfilename, int extract_frimware, char *kernelfilename, char *ramdiskfilename, char *imagefilename, char *configfilename ); | ||
+ | int pack_firmware(char *flashfilename, char *kernelfilename, char *ramdiskfilename, char *imagefilename, char * configfilename ); | ||
+ | |||
+ | void firmware_unpack_extract(char *inFileName, char *outFileName, UINT32 inFileOffset, UINT32 dataLenght); | ||
+ | UINT32 firmware_calc_checksum(char *inFileName); | ||
+ | int calc_checksum(char *filename); | ||
+ | int check_size(char *filename, UINT32 *file_size, UINT32 max_size); | ||
+ | char * strtolower(const char *ret); | ||
+ | int compare(char *filename1, char *filename2); | ||
+ | |||
+ | |||
+ | char *strtolower(const char *ret) | ||
+ | { | ||
+ | char *s = ret; | ||
+ | for ( s = ret;*s != 0; s++) | ||
+ | { | ||
+ | if (*s != 0) | ||
+ | { *s = tolower(*s); } | ||
+ | } | ||
+ | return ret; | ||
+ | } | ||
+ | |||
+ | int main(int argc, char **argv) | ||
+ | { | ||
+ | int showHelp = 1; | ||
+ | |||
+ | if (argc == 3) | ||
+ | { | ||
+ | strtolower(argv[1]); | ||
+ | if ( strcmp("-s",argv[1]) == 0) | ||
+ | { showFirmware(argv[2], 0, "", "", "", "" ); showHelp--; } | ||
+ | |||
+ | if ( strcmp("-x",argv[1]) == 0) | ||
+ | { showFirmware(argv[2], 1, "uImage", "uRamDisk", "image.cfs", "default.tar.gz" ); showHelp--; } | ||
+ | |||
+ | if ( strcmp("-mf",argv[1]) == 0) | ||
+ | { pack_firmware(argv[2],"uImage", "uRamDisk", "image.cfs", "default.tar.gz"); showHelp--; } | ||
+ | |||
+ | } | ||
+ | |||
+ | if (argc == 4) | ||
+ | { | ||
+ | strtolower(argv[1]); | ||
+ | if ( strcmp("-cmp",argv[1]) == 0) | ||
+ | { compare(argv[2], argv[3]); showHelp--; } | ||
+ | } | ||
+ | |||
+ | if (argc == 8) | ||
+ | { | ||
+ | strtolower(argv[1]); | ||
+ | if ( strcmp("-m",argv[1]) == 0) | ||
+ | { | ||
+ | strtolower(argv[6]); | ||
+ | if ( strcmp("-f",argv[6]) == 0) | ||
+ | { pack_firmware(argv[7],argv[2], argv[3], argv[4], argv[5]); showHelp--; } | ||
+ | } | ||
+ | |||
+ | if ( strcmp("-x",argv[1]) == 0) | ||
+ | { | ||
+ | strtolower(argv[3]); | ||
+ | if ( strcmp("-o",argv[3]) == 0) | ||
+ | { showFirmware(argv[2], 1, argv[4], argv[5], argv[6], argv[7] ); showHelp--; } | ||
+ | } | ||
+ | } | ||
+ | |||
+ | if (showHelp) | ||
+ | { | ||
+ | printf("Copyright 2011 by Magnus Olsen (magnus@greatlord.com)\n"); | ||
+ | printf("This program are under licen GPL 2.0\n\n"); | ||
+ | printf("Merge kernel (uImage) + ramdisk (uRamDisk) + image (image.cfs) and\nconfig (default.tar.gz) to a flash image for dlink DNS320\n\n"); | ||
+ | printf("dns320flash -m kernel ramdisk image config -f dlink320firmware\n\n\n"); | ||
+ | printf("dns320flash -mf dlink320firmware dlink320firmware\n\n\n"); | ||
+ | printf("Extract flash image to kernel (uImage) + ramdisk (uRamDisk) + \nimage (image.cfs) and config (default.tar.gz) for dlink DNS320\n\n"); | ||
+ | printf("dns320flash -x dlink320firmware -o kernel ramdisk image config\n"); | ||
+ | printf("dns320flash -x dlink320firmware \n\n\n"); | ||
+ | printf("Show flash image contains for dlink DNS320\n\n"); | ||
+ | printf("dns320flash -s dlink320firmware\n\n\n"); | ||
+ | } | ||
+ | |||
+ | return 0; | ||
+ | } | ||
+ | |||
+ | void showFirmware(char *flashfilename, int extract_frimware, char *kernelfilename, char *ramdiskfilename, char *imagefilename, char * configfilename ) | ||
+ | { | ||
+ | int read_byte; | ||
+ | FILE *fp; | ||
+ | char str[10]; | ||
+ | DLINK_DNS320_FIRMWARE_HEAD_128BYTE dnsHeader; | ||
+ | |||
+ | |||
+ | fp = fopen(flashfilename,"rb"); | ||
+ | if (fp) | ||
+ | { | ||
+ | memset( &dnsHeader,0,sizeof(DLINK_DNS320_FIRMWARE_HEAD_128BYTE)); | ||
+ | read_byte = fread(&dnsHeader, 1, sizeof(DLINK_DNS320_FIRMWARE_HEAD_128BYTE),fp); | ||
+ | fclose(fp); | ||
+ | |||
+ | if (read_byte != sizeof(DLINK_DNS320_FIRMWARE_HEAD_128BYTE)) | ||
+ | { | ||
+ | printf("not vaild firmware for DNS320"); | ||
+ | exit(0); | ||
+ | } | ||
+ | |||
+ | memcpy(&str,dnsHeader.strModelName,9); | ||
+ | str[9] = 0; | ||
+ | |||
+ | if ( (dnsHeader.magic_0 != 0x55) || | ||
+ | (dnsHeader.magic_1 != 0xAA) || | ||
+ | (dnsHeader.magic_2 != 0xAA) || | ||
+ | (dnsHeader.productId != 0x00) || | ||
+ | (dnsHeader.customId != 0x08) || | ||
+ | (dnsHeader.modelId != 0x07) || | ||
+ | (dnsHeader.hardwareId != 0x01) || | ||
+ | (dnsHeader.subId != 0x00) || | ||
+ | (strcmp(str,"DNS323D1U") != 0) ) | ||
+ | { | ||
+ | printf("not vaild firmware for DNS320"); | ||
+ | exit(0); | ||
+ | } | ||
+ | |||
+ | printf("magic_0 : %02x\n",dnsHeader.magic_0); | ||
+ | printf("magic_1 : %02x\n",dnsHeader.magic_1); | ||
+ | printf("string : %s\n",str); | ||
+ | printf("magic_2 : %02x\n",dnsHeader.magic_2); | ||
+ | printf("productId : %02x\n",dnsHeader.productId); | ||
+ | printf("customId : %02x\n",dnsHeader.customId); | ||
+ | printf("modelId : %02x\n",dnsHeader.modelId); | ||
+ | printf("hardwareId : %02x\n",dnsHeader.hardwareId); | ||
+ | printf("subId : %02x\n",dnsHeader.subId); | ||
+ | printf("Next_offset : %08x\n\n",dnsHeader.NextOffset); | ||
+ | |||
+ | printf("Kernel (uImage) Offset head : %08x\n",dnsHeader.uImageOffset); | ||
+ | printf("Kernel (uImage) Lenght head : %08x\n",dnsHeader.uImageLenght); | ||
+ | printf("Kernel (uImage) Checksum head : %08x\n",dnsHeader.uImageChecksum); | ||
+ | |||
+ | |||
+ | if (extract_frimware) | ||
+ | { | ||
+ | firmware_unpack_extract(flashfilename, kernelfilename, dnsHeader.uImageOffset, dnsHeader.uImageLenght); | ||
+ | printf("Kernel (uImage) Checksum file : %08x\n\n",calc_checksum(kernelfilename)); | ||
+ | } | ||
+ | else | ||
+ | { printf("\n"); } | ||
+ | |||
+ | printf("uRamDisk Offset head : %08x\n",dnsHeader.uRamDiskOffset); | ||
+ | printf("uRamDisk Lenght head : %08x\n",dnsHeader.uRamDiskLenght); | ||
+ | printf("uRamDisk Checksum head : %08x\n",dnsHeader.uRamDiskChecksum); | ||
+ | if (extract_frimware) | ||
+ | { | ||
+ | |||
+ | firmware_unpack_extract(flashfilename, ramdiskfilename, dnsHeader.uRamDiskOffset, dnsHeader.uRamDiskLenght); | ||
+ | printf("uRamDisk Checksum file : %08x\n\n",calc_checksum(ramdiskfilename)); | ||
+ | } | ||
+ | else | ||
+ | { printf("\n"); } | ||
+ | |||
+ | |||
+ | printf("image Offset head : %08x\n",dnsHeader.ImageOffset); | ||
+ | printf("image Lenght head : %08x\n",dnsHeader.ImageLenght); | ||
+ | printf("image Checksum head : %08x\n",dnsHeader.ImageChecksum); | ||
+ | |||
+ | if (extract_frimware) | ||
+ | { | ||
+ | firmware_unpack_extract(flashfilename, imagefilename, dnsHeader.ImageOffset, dnsHeader.ImageLenght); | ||
+ | printf("image Checksum file : %08x\n\n",calc_checksum(imagefilename)); | ||
+ | } | ||
+ | else | ||
+ | { printf("\n"); } | ||
+ | |||
+ | printf("Default Offset head : %08x\n",dnsHeader.DefaultOffset); | ||
+ | printf("Default Lenght head : %08x\n",dnsHeader.DefaultLenght); | ||
+ | printf("Default Checksum head : %08x\n",dnsHeader.DefaultChecksum); | ||
+ | |||
+ | |||
+ | if (extract_frimware) | ||
+ | { | ||
+ | firmware_unpack_extract(flashfilename, configfilename, dnsHeader.DefaultOffset, dnsHeader.DefaultLenght); | ||
+ | printf("Default Checksum file : %08x\n\n",calc_checksum(configfilename)); | ||
+ | } | ||
+ | else | ||
+ | { printf("\n"); } | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | } | ||
+ | |||
+ | } | ||
+ | |||
+ | void firmware_unpack_extract(char *inFileName, char *outFileName, UINT32 inFileOffset, UINT32 dataLenght) | ||
+ | { | ||
+ | FILE *read_fp; | ||
+ | FILE *save_fp; | ||
+ | BYTE *ch; | ||
+ | UINT32 lenght = 0; | ||
+ | printf("Extracting %s from %s\n",outFileName, inFileName); | ||
+ | read_fp = fopen(inFileName,"rb"); | ||
+ | if (read_fp) | ||
+ | { | ||
+ | fseek(read_fp,inFileOffset, SEEK_SET); | ||
+ | save_fp = fopen(outFileName,"wb+"); | ||
+ | if (save_fp) | ||
+ | { | ||
+ | while(lenght<dataLenght) | ||
+ | { | ||
+ | fread(&ch,1,1,read_fp); | ||
+ | fwrite(&ch,1,1,save_fp); | ||
+ | lenght++; | ||
+ | } | ||
+ | printf("writing done\n"); | ||
+ | fclose(save_fp); | ||
+ | } | ||
+ | fclose(read_fp); | ||
+ | } | ||
+ | } | ||
+ | |||
+ | int pack_firmware(char *flashfilename, char *kernelfilename, char *ramdiskfilename, char *imagefilename, char * configfilename ) | ||
+ | { | ||
+ | FILE *fp_read; | ||
+ | FILE *fp_save; | ||
+ | int i, kernelSize,ramdiskSize, imageSize, configSize; | ||
+ | UINT32 byte; | ||
+ | DLINK_DNS320_FIRMWARE_HEAD_128BYTE dnsHeader; | ||
+ | |||
+ | memset(&dnsHeader,0,sizeof(DLINK_DNS320_FIRMWARE_HEAD_128BYTE)); | ||
+ | |||
+ | |||
+ | if ( check_size(kernelfilename, &dnsHeader.uImageLenght, 0x00300000) == -1) | ||
+ | { return -1; } | ||
+ | |||
+ | if ( check_size(ramdiskfilename, &dnsHeader.uRamDiskLenght, 0x00300000) == -1) | ||
+ | { return -1; } | ||
+ | |||
+ | if ( check_size(configfilename, &dnsHeader.DefaultLenght, 0x00300000) == -1) | ||
+ | { return -1; } | ||
+ | |||
+ | if ( check_size(imagefilename, &dnsHeader.ImageLenght, 0x04000000) == -1) | ||
+ | { return -1; } | ||
+ | |||
+ | |||
+ | dnsHeader.magic_0 = 0x55; | ||
+ | dnsHeader.magic_1 = 0xAA; | ||
+ | dnsHeader.magic_2 = 0xAA; | ||
+ | dnsHeader.productId = 0x00; | ||
+ | dnsHeader.customId = 0x08; | ||
+ | dnsHeader.modelId = 0x07; | ||
+ | dnsHeader.hardwareId = 0x01; | ||
+ | dnsHeader.subId = 0x00; | ||
+ | memcpy(dnsHeader.strModelName,"DNS323D1U",9); | ||
+ | |||
+ | |||
+ | dnsHeader.uImageChecksum = calc_checksum(kernelfilename); | ||
+ | dnsHeader.uRamDiskChecksum = calc_checksum(ramdiskfilename); | ||
+ | dnsHeader.DefaultChecksum = calc_checksum(configfilename); | ||
+ | dnsHeader.ImageChecksum = calc_checksum(imagefilename); | ||
+ | |||
+ | |||
+ | kernelSize = dnsHeader.uImageLenght; | ||
+ | ramdiskSize = dnsHeader.uRamDiskLenght; | ||
+ | imageSize = dnsHeader.ImageLenght; | ||
+ | configSize = dnsHeader.DefaultLenght; | ||
+ | |||
+ | if ((dnsHeader.uImageLenght % 4) != 0) | ||
+ | { dnsHeader.uImageLenght = ALGIN4(dnsHeader.uImageLenght); } | ||
+ | |||
+ | if ((dnsHeader.uRamDiskLenght % 4) != 0) | ||
+ | { dnsHeader.uRamDiskLenght = ALGIN4(dnsHeader.uRamDiskLenght); } | ||
+ | |||
+ | if ((dnsHeader.ImageLenght % 4) != 0) | ||
+ | { dnsHeader.ImageLenght = ALGIN4(dnsHeader.ImageLenght); } | ||
+ | |||
+ | if ((dnsHeader.DefaultLenght % 4) != 0) | ||
+ | { dnsHeader.DefaultLenght = ALGIN4(dnsHeader.DefaultLenght); } | ||
+ | |||
+ | |||
+ | dnsHeader.uImageOffset = sizeof(DLINK_DNS320_FIRMWARE_HEAD_128BYTE); | ||
+ | dnsHeader.uRamDiskOffset = sizeof(DLINK_DNS320_FIRMWARE_HEAD_128BYTE) + dnsHeader.uImageLenght; | ||
+ | dnsHeader.ImageOffset = sizeof(DLINK_DNS320_FIRMWARE_HEAD_128BYTE) + dnsHeader.uImageLenght + dnsHeader.uRamDiskLenght ; | ||
+ | |||
+ | dnsHeader.DefaultOffset = sizeof(DLINK_DNS320_FIRMWARE_HEAD_128BYTE) + dnsHeader.uImageLenght + dnsHeader.uRamDiskLenght + dnsHeader.ImageLenght ; | ||
+ | |||
+ | printf("Kernel (uImage) Offset : %08x\n",dnsHeader.uImageOffset); | ||
+ | printf("Kernel (uImage) Lenght : %08x\n",dnsHeader.uImageLenght); | ||
+ | printf("Kernel (uImage) Checksum : %08x\n\n",dnsHeader.uImageChecksum); | ||
+ | printf("uRamDisk Offset : %08x\n",dnsHeader.uRamDiskOffset); | ||
+ | printf("uRamDisk Lenght : %08x\n",dnsHeader.uRamDiskLenght); | ||
+ | printf("uRamDisk Checksum : %08x\n\n",dnsHeader.uRamDiskChecksum); | ||
+ | printf("image Offset : %08x\n",dnsHeader.ImageOffset); | ||
+ | printf("image Lenght : %08x\n",dnsHeader.ImageLenght); | ||
+ | printf("image Checksum : %08x\n\n",dnsHeader.ImageChecksum); | ||
+ | printf("Default Offset : %08x\n",dnsHeader.DefaultOffset); | ||
+ | printf("Default Lenght : %08x\n",dnsHeader.DefaultLenght); | ||
+ | printf("Default Checksum : %08x\n\n",dnsHeader.DefaultChecksum); | ||
+ | |||
+ | if ( (fp_save = fopen(flashfilename,"wb+")) == 0) | ||
+ | { | ||
+ | printf("Error : Can not merge firmware\n"); | ||
+ | return -1; | ||
+ | } | ||
+ | |||
+ | fwrite(&dnsHeader,1,sizeof(DLINK_DNS320_FIRMWARE_HEAD_128BYTE),fp_save); | ||
+ | |||
+ | if ( (fp_read = fopen(kernelfilename,"rb")) == 0) | ||
+ | { | ||
+ | printf("Error : Can not merge firmware\n"); | ||
+ | return -1; | ||
+ | } | ||
+ | for(i=0;i<dnsHeader.uImageLenght/4;i++) | ||
+ | { | ||
+ | fread(&byte,1,4,fp_read); | ||
+ | fwrite(&byte,1,4,fp_save); | ||
+ | } | ||
+ | fclose(fp_read); | ||
+ | |||
+ | if ( (fp_read = fopen(ramdiskfilename,"rb")) == 0) | ||
+ | { | ||
+ | printf("Error : Can not merge firmware\n"); | ||
+ | return -1; | ||
+ | } | ||
+ | for(i=0;i<dnsHeader.uRamDiskLenght/4;i++) | ||
+ | { | ||
+ | fread(&byte,1,4,fp_read); | ||
+ | fwrite(&byte,1,4,fp_save); | ||
+ | } | ||
+ | fclose(fp_read); | ||
+ | |||
+ | if ( (fp_read = fopen(imagefilename,"rb")) == 0) | ||
+ | { | ||
+ | printf("Error : Can not merge firmware\n"); | ||
+ | return -1; | ||
+ | } | ||
+ | for(i=0;i<dnsHeader.ImageLenght/4;i++) | ||
+ | { | ||
+ | fread(&byte,1,4,fp_read); | ||
+ | fwrite(&byte,1,4,fp_save); | ||
+ | } | ||
+ | |||
+ | fclose(fp_read); | ||
+ | |||
+ | if ( (fp_read = fopen(configfilename,"rb")) == 0) | ||
+ | { | ||
+ | printf("Error : Can not merge firmware\n"); | ||
+ | return -1; | ||
+ | } | ||
+ | |||
+ | for(i=0;i<dnsHeader.DefaultLenght/4;i++) | ||
+ | { | ||
+ | fread(&byte,1,4,fp_read); | ||
+ | fwrite(&byte,1,4,fp_save); | ||
+ | } | ||
+ | fclose(fp_read); | ||
+ | |||
+ | |||
+ | fclose(fp_save); | ||
+ | |||
+ | return 0; | ||
+ | } | ||
+ | |||
+ | |||
+ | int check_size(char *filename, UINT32 *file_size, UINT32 max_size) | ||
+ | { | ||
+ | FILE *fp_read; | ||
+ | |||
+ | if ((fp_read = fopen(filename,"rb")) ) | ||
+ | { | ||
+ | fseek(fp_read,0,SEEK_END); | ||
+ | *file_size = ftell(fp_read); | ||
+ | if ( *file_size >= max_size ) | ||
+ | { | ||
+ | printf("\nMake firmware error\n"); | ||
+ | printf("Ramdisk sizes can not more than %d byte",max_size); | ||
+ | return -1; | ||
+ | } | ||
+ | fclose(fp_read); | ||
+ | } | ||
+ | else | ||
+ | { | ||
+ | printf("Can not open file uImage\n"); | ||
+ | } | ||
+ | return 0; | ||
+ | } | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | int calc_checksum(char *filename) | ||
+ | { | ||
+ | FILE *fp_read; | ||
+ | UINT32 chk_sum = 0; | ||
+ | int byte,size,filesize; | ||
+ | |||
+ | if (!(fp_read = fopen(filename,"rb"))) | ||
+ | { | ||
+ | printf("Error: Can't open %s file !\n", filename); | ||
+ | return 0; | ||
+ | } | ||
+ | |||
+ | fseek(fp_read, 0, SEEK_END); | ||
+ | filesize = ftell(fp_read); | ||
+ | fseek(fp_read, 0, SEEK_SET); | ||
+ | |||
+ | for(size=0;size<filesize;size+=4) | ||
+ | { | ||
+ | byte = 0; | ||
+ | fread(&byte, 1, 4, fp_read); | ||
+ | chk_sum ^= byte; | ||
+ | } | ||
+ | |||
+ | fclose(fp_read); | ||
+ | return chk_sum; | ||
+ | } | ||
+ | |||
+ | int compare(char *filename1, char *filename2) | ||
+ | { | ||
+ | FILE *fp_read1; | ||
+ | FILE *fp_read2; | ||
+ | int file1_size; | ||
+ | int file2_size; | ||
+ | int i; | ||
+ | |||
+ | if ((fp_read1 = fopen(filename1,"rb")) == 0) | ||
+ | { printf("Error : Can not open file %s\n",filename1); return -1; } | ||
+ | |||
+ | if ((fp_read2 = fopen(filename2,"rb")) == 0) | ||
+ | { printf("Error : Can not open file %s\n",filename2); fclose(fp_read1); return -1; } | ||
+ | |||
+ | fseek(fp_read1,0,SEEK_END); | ||
+ | fseek(fp_read2,0,SEEK_END); | ||
+ | |||
+ | file1_size = ftell(fp_read1); | ||
+ | file2_size = ftell(fp_read2); | ||
+ | |||
+ | fseek(fp_read1,0,SEEK_SET); | ||
+ | fseek(fp_read2,0,SEEK_SET); | ||
+ | |||
+ | if (file1_size != file2_size) | ||
+ | { | ||
+ | printf("Error : File %s and file %s does not have same filesize\n",filename1,filename2); | ||
+ | fclose(fp_read1); | ||
+ | fclose(fp_read2); | ||
+ | return -1; | ||
+ | } | ||
+ | |||
+ | for (i=0;i<file1_size;i++) | ||
+ | { | ||
+ | if ( fgetc(fp_read1) != fgetc(fp_read2) ) | ||
+ | { | ||
+ | printf("Error : Byte are not same\n"); | ||
+ | printf("FileOffset : %08lx\n",ftell(fp_read1)); | ||
+ | fclose(fp_read1); | ||
+ | fclose(fp_read2); | ||
+ | return -1; | ||
+ | } | ||
+ | |||
+ | } | ||
+ | fclose(fp_read1); | ||
+ | fclose(fp_read2); | ||
+ | return 0; | ||
+ | } | ||
+ | |||
+ | |||
+ | </code> | ||
+ | |||
===== Other info ===== | ===== Other info ===== | ||
- | The following [[http://forum.dsmg600.info/viewtopic.php?id=6094|thread]] handles some DNS-320 initial conversation, request there if you want some specific info here, or add yourself. | + | The following [[http://dns323.kood.org/forum/viewtopic.php?id=6094|thread]] handles some DNS-320 initial conversation, request there if you want some specific info here, or add yourself. |
+ | |||
+ | |||
+ | ===== Fan Speed settings ===== | ||
+ | |||
+ | With ffp is enabled, login to the box via telnet and run FT_testing | ||
+ | |||
+ | ex: | ||
+ | <code> | ||
+ | / # FT_testing -H | ||
+ | Fan and Temperature Testing Tools | ||
+ | Usage | ||
+ | FT_testing -H ...Help message | ||
+ | FT_testing -T ...Get Temperature | ||
+ | FT_testing -F ...Set Fan in Full Speed | ||
+ | FT_testing -L ...Set Fan in Low Speed | ||
+ | FT_testing -S ...Set Fan Stop | ||
+ | FT_testing -A ...Print Receive UART Packet. | ||
+ | FT_testing -G ...Get Fan Status. | ||
+ | FT_testing -P ...Power off system. | ||
+ | FT_testing -R ...Reboot system. | ||
+ | </code> | ||
+ | |||
+ | if you need the fan is always off, type: | ||
+ | <code> | ||
+ | ps uax |grep fan_control | ||
+ | </code> | ||
+ | and kill this process | ||
+ | |||
+ | or <code>killall fan_control</code>, and run <code>FT_testing -S</code>/code | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ===== SSH Access ===== | ||
+ | This is just a quick n' dirty way to get root access to the device. This configuration is __not__ recommended as permanent. | ||
+ | |||
+ | - Create fun_plug | ||
+ | - Create sshd_config | ||
+ | - reboot dns-320 | ||
+ | |||
+ | |||
+ | **File 1 fun_plug * ** | ||
+ | <code> | ||
+ | #!/bin/sh | ||
+ | # credit to | ||
+ | # http://webapps.itcs.umich.edu/radmind/index.php/Generate_ssh_host_keys | ||
+ | # for the scripted ssh-keygen | ||
+ | |||
+ | ssh-keygen -q -t dsa -f /mnt/HD/HD_a2/ssh_host_dsa_key -N ""\ | ||
+ | -C "" < /dev/null > /dev/null 2> /dev/null | ||
+ | |||
+ | /usr/sbin/sshd -f /mnt/HD/HD_a2/sshd_config | ||
+ | </code> | ||
+ | |||
+ | **File 2 sshd_config * ** | ||
+ | <code> | ||
+ | Port 22 | ||
+ | Protocol 2 | ||
+ | HostKey /mnt/HD/HD_a2/ssh_host_dsa_key | ||
+ | PermitEmptyPasswords yes | ||
+ | PasswordAuthentication yes | ||
+ | ChallengeResponseAuthentication no | ||
+ | TCPKeepAlive yes | ||
+ | </code> | ||
+ | |||
+ | * Create the files with a Linux compatible text editor (Like [[http://notepad-plus.sourceforge.net/uk/site.htm|Notepad++]]) | ||
+ | |||
+ | Connect: ''ssh root@dns_ip'' | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ===== Detect USB button pressure ===== | ||
+ | I wanted to replace the 8 seconds pressure on the power button by a simple pressure on the usb button. | ||
+ | So, i've analysed the chk_io program while it seemed to be the one which does the job for the usb copy. | ||
+ | The chk_io is not gpl, so only the binary is available. I used strace and LD_PRELOAD on ioctl to analyse it, | ||
+ | and finally found a similar program for the dns-323. | ||
+ | |||
+ | I'm not sure it's required to open /dev/REG each time, but it's what the official program does. | ||
+ | Idem for the open attributes. | ||
+ | |||
+ | I've created : | ||
+ | |||
+ | * ffp/extra/shutdown/chkbutton (gcc -static -s chkbutton.c -o chkbutton) | ||
+ | |||
+ | * /ffp/extra/shutdown/shutdown_ffp.sh | ||
+ | |||
+ | * /ffp/extra/shutdown/usbOff.sh | ||
+ | |||
+ | * /ffp/etc/fun_plug.local | ||
+ | |||
+ | Just copy these files or feel free to modify them. | ||
+ | |||
+ | Files are available here : http://nadenislamarre.free.fr/dns320 | ||
+ | |||
+ | <code> | ||
+ | # chkbutton.c | ||
+ | |||
+ | #define _GNU_SOURCE 1 | ||
+ | #include <stdio.h> | ||
+ | #include <stdlib.h> | ||
+ | #include <fcntl.h> | ||
+ | |||
+ | #define DEVICE "/dev/REG" | ||
+ | #define REQUEST 0x65 | ||
+ | #define REGISTER 0x10110 | ||
+ | #define BTN_NOTUSB 0x08000000 | ||
+ | |||
+ | int main (int argc, char *argv[]) { | ||
+ | int fd; | ||
+ | unsigned long data[2]; | ||
+ | |||
+ | while(1) { | ||
+ | if ((fd = open (DEVICE, O_RDWR|O_LARGEFILE)) == -1) { | ||
+ | exit(1); | ||
+ | } | ||
+ | |||
+ | data[0] = REGISTER; | ||
+ | data[1] = 0; | ||
+ | |||
+ | if(ioctl(fd, REQUEST, &data) == 0) { | ||
+ | if(! ((data[1] & BTN_NOTUSB) == BTN_NOTUSB)) { | ||
+ | printf("USB\n"); | ||
+ | fflush(stdout); | ||
+ | usleep(1000 * 1000 * 3); | ||
+ | } | ||
+ | } | ||
+ | |||
+ | close(fd); | ||
+ | usleep(1000*30); | ||
+ | } | ||
+ | |||
+ | return 0; | ||
+ | } | ||
+ | </code> | ||
+ | |||
+ | The following script called in the /ffp/etc/fun_plug.local make the dns-320 reboot just by pressing on the usb button. | ||
+ | The redirection to /dev/null is required because the shutdown.sh script kill processes on some conditions. | ||
+ | |||
+ | <code> | ||
+ | #!/bin/sh | ||
+ | |||
+ | # /ffp/extra/shutdown/usbOff.sh | ||
+ | |||
+ | export PATH=$PATH:/bin:/sbin | ||
+ | |||
+ | chkbutton | | ||
+ | while read BTN | ||
+ | do | ||
+ | if test "$BTN" = "USB" | ||
+ | then | ||
+ | led usb blue blinking | ||
+ | shutdown_ffp.sh >/dev/null 2>/dev/null | ||
+ | exit 0 | ||
+ | fi | ||
+ | done | ||
+ | </code> | ||
+ | |||
+ | <code> | ||
+ | #!/bin/sh | ||
+ | |||
+ | # /ffp/etc/fun_plug.local | ||
+ | |||
+ | # replacement for shutdown ; must not be on a mounted device | ||
+ | cp /ffp/extra/shutdown/* /sbin | ||
+ | usbOff.sh& | ||
+ | </code> | ||
+ | |||
+ | The shutdown script is the same as the official one except that i've added a proper shutdown for ffp : /ffp/etc/rc stop | ||
+ | |||
+ | <code> | ||
+ | #!/bin/sh | ||
+ | |||
+ | # /ffp/extra/shutdown/shutdown_ffp.sh | ||
+ | |||
+ | source /usr/local/modules/files/project_features | ||
+ | |||
+ | /ffp/etc/rc stop | ||
+ | |||
+ | kill_running_process | ||
+ | #kill -9 -1 | ||
+ | |||
+ | # remove link file | ||
+ | rm /usr/local/upload | ||
+ | sync | ||
+ | |||
+ | umount_dev.sh all | ||
+ | |||
+ | umount /usr/local/config | ||
+ | |||
+ | sleep 1 | ||
+ | # shutdown device | ||
+ | |||
+ | MODEL=$(cat "/usr/local/modules/files/model") | ||
+ | echo "MODEL:$MODEL" | ||
+ | |||
+ | if [ "$PROJECT_FEATURE_MCU_CHIP_WT693P" = "1" ]; then | ||
+ | echo "device shutdown" | ||
+ | up_send_ctl DeviceShutdown 0 | ||
+ | |||
+ | elif [ "$PROJECT_FEATURE_MCU_CHIP_69P803" = "1" ]; then | ||
+ | echo "send cmd to micro-p to shutdown" | ||
+ | up_send_ctl DeviceShutdown 1 | ||
+ | else | ||
+ | poweroff | ||
+ | fi | ||
+ | </code> | ||