This shows you the differences between the selected revision and the current version of the page.

dns-320l 2015/05/15 22:16 dns-320l 2017/09/06 18:38 current
Line 1: Line 1:
====== DNS-320L ====== ====== DNS-320L ======
This page will share some more information about the [[http://www.dlink.com/uk/en/home-solutions/share/network-attached-storage/dns-320l-sharecenter-2-bay-cloud-storage-enclosure|ShareCenter 2-Bay Cloud Network Storage Enclosure (DNS-320L)]].\\ This page will share some more information about the [[http://www.dlink.com/uk/en/home-solutions/share/network-attached-storage/dns-320l-sharecenter-2-bay-cloud-storage-enclosure|ShareCenter 2-Bay Cloud Network Storage Enclosure (DNS-320L)]].\\
===== Hardware ===== ===== Hardware =====
Line 6: Line 7:
{{ dns-320l_sm.png|thumb|Front angle view of the DNS-320L}} {{ dns-320l_sm.png|thumb|Front angle view of the DNS-320L}}
-^ CPU | Feroceon 88FR131 rev 1 (v5l) |+^ CPU |1000 MHz Marvell (88F6702-A1, identified by Linux as Feroceon 88FR131 rev 1 (v5l)) |
^ RAM | 256 MB | ^ RAM | 256 MB |
^ USB | 1 USB2.0 Port (rear) | ^ USB | 1 USB2.0 Port (rear) |
Line 70: Line 71:
VmallocChunk:    382892 kB VmallocChunk:    382892 kB
</code> </code>
Line 77: Line 79:
===== Serial PIN Layout ===== ===== Serial PIN Layout =====
-Unknown, may be similar to [[DNS-320]].+Very similar to [[DNS-320]].
 +Image from a DNBS-320L, rev. A3
 +===== UBoot boot messages =====
 +U-Boot 1.1.4 (Apr 17 2014 - 17:31:34) Marvell version: 3.6.0.DNS-320L.01
 +U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFB00
 +Soc: 88F6702 A1 CPU running @ 1000Mhz L2 running @ 500Mhz
 +SysClock = 400Mhz , TClock = 166Mhz
 +DRAM (DDR2) CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
 +DRAM CS[0] base 0x00000000  size 256MB
 +DRAM Total size 256MB  16bit width
 +Addresses 8M - 0M are saved for the U-Boot usage.
 +Mem malloc Initialization (8M - 7M): Done
 +NAND:128 MB
 +Flash:  0 kB
 +CPU : Marvell Feroceon (Rev 1)
 +Streaming disabled
 +Write allocate disabled
 +USB 0: host mode
 +PEX 0: interface detected no Link.
 +Net:  egiga0 [PRIME]
 +Hit any key to stop autoboot:  0
 +NAND read: device 0 offset 0x100000, size 0x300000
 +load addr ....  =a00000
 + 3145728 bytes read: OK
 +NAND read: device 0 offset 0x600000, size 0x300000
 +load addr ....  =f00000
 + 3145728 bytes read: OK
 +## Booting image at 00a00000 ...
 +  Image Name:  Linux-
 +  Created:      2012-08-22  8:55:08 UTC
 +  Image Type:  ARM Linux Kernel Image (uncompressed)
 +  Data Size:    2630552 Bytes =  2.5 MB
 +  Load Address: 00008000
 +  Entry Point:  00008000
 +  Verifying Checksum ... OK
 +## Loading Ramdisk Image at 00f00000 ...
 +  Image Name:  Ramdisk
 +  Created:      2015-07-28  13:12:19 UTC
 +  Image Type:  ARM Linux RAMDisk Image (gzip compressed)
 +  Data Size:    1744063 Bytes =  1.7 MB
 +  Load Address: 00e00000
 +  Entry Point:  00e00000
 +  Verifying Checksum ... OK
 +Starting kernel ...
 +Uncompressing Linux......................................................................................................................................................................... done, bo.
===== Serial console boot messages ===== ===== Serial console boot messages =====
-Unknown, may be similar to [[DNS-320]].+<code> 
 +Linux version (jack@swtest6) (gcc version 4.3.2 (sdk3.3-ct-ng-1.4.1) ) #1 Wed Aug 22 16:55:05 CST 2012 
 +CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053977 
 +CPU: VIVT data cache, VIVT instruction cache 
 +Machine: Feroceon-KW 
 +Using UBoot passing parameters structure 
 +Memory policy: ECC disabled, Data cache writeback 
 +Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 65024 
 +Kernel command line: root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none 
 +PID hash table entries: 1024 (order: 10, 4096 bytes) 
 +Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) 
 +Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) 
 +Memory: 256MB = 256MB total 
 +Memory: 246272KB available (4960K code, 334K data, 136K init, 0K highmem) 
 +Hierarchical RCU implementation. 
 +Console: colour dummy device 80x30 
 +Calibrating delay loop... 999.42 BogoMIPS (lpj=4997120) 
 +Mount-cache hash table entries: 512 
 +CPU: Testing write buffer coherency: ok 
 +NET: Registered protocol family 16 
 +Feroceon L2: Enabling L2 
 +Feroceon L2: Cache support initialised. 
 +CPU Interface 
 +SDRAM_CS0 ....base 00000000, size 256MB  
 +SDRAM_CS1 ....disable 
 +SDRAM_CS2 ....disable 
 +SDRAM_CS3 ....disable 
 +PEX0_MEM ....base e0000000, size 128MB  
 +PEX0_IO ....base f2000000, size  1MB  
 +PEX1_MEM ....no such 
 +PEX1_IO ....no such 
 +INTER_REGS ....base f1000000, size  1MB  
 +NFLASH_CS ....base fa000000, size  2MB  
 +SPI_CS ....base f4000000, size  16MB  
 +BOOT_ROM_CS ....no such 
 +DEV_BOOTCS ....no such 
 +CRYPT_ENG ....base f0000000, size  2MB  
 +  Marvell Development Board (LSP Version KW_LSP_5.1.3_patch29)-- DB-88F6702A-BP  Soc: 88F6702 A1 LE 
 + Detected Tclk 166666667 and SysClk 400000000  
 +MV Buttons Device Load 
 +Marvell USB EHCI Host controller #0: c8040740 
 +PEX0 interface detected no Link. 
 +PCI: bus0: Fast back to back transfers enabled 
 +mvPexLocalBusNumSet: ERR. Invalid PEX interface 1 
 +bio: create slab <bio-0> at 0 
 +SCSI subsystem initialized 
 +usbcore: registered new interface driver usbfs 
 +usbcore: registered new interface driver hub 
 +usbcore: registered new device driver usb 
 +NET: Registered protocol family 2 
 +IP route cache hash table entries: 2048 (order: 1, 8192 bytes) 
 +TCP established hash table entries: 8192 (order: 4, 65536 bytes) 
 +TCP bind hash table entries: 8192 (order: 3, 32768 bytes) 
 +TCP: Hash tables configured (established 8192 bind 8192) 
 +TCP reno registered 
 +NET: Registered protocol family 1 
 +Trying to unpack rootfs image as initramfs... 
 +rootfs image is not initramfs (no cpio magic); looks like an initrd 
 +Freeing initrd memory: 1700K 
 +RTC has been updated!!! 
 +rtc mv_rtc: rtc core: registered kw-rtc as rtc0 
 +RTC registered 
 +cpufreq: Init kirkwood cpufreq driver 
 +XOR registered 4 channels 
 +XOR 2nd invalidate WA enabled 
 +mvCesaInit: sessions=640, queue=64, pSram=f0000000 
 +MV Buttons Driver Load 
 +VFS: Disk quotas dquot_6.5.2 
 +Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) 
 +squashfs: version 4.0 (2009/01/31) Phillip Lougher 
 +Installing knfsd (copyright (C) 1996 okir@monad.swb.de). 
 +NTFS driver 2.1.29 [Flags: R/O]. 
 +JFFS2 version 2.2. (NAND) �© 2001-2006 Red Hat, Inc. 
 +fuse init (API version 7.12) 
 +msgmni has been set to 484 
 +alg: No test for cipher_null (cipher_null-generic) 
 +alg: No test for ecb(cipher_null) (ecb-cipher_null) 
 +alg: No test for digest_null (digest_null-generic) 
 +alg: No test for compress_null (compress_null-generic) 
 +alg: No test for lzma (lzma-generic) 
 +alg: No test for stdrng (krng) 
 +alg: No test for hmac(digest_null) (hmac(digest_null-generic)) 
 +Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) 
 +io scheduler noop registered 
 +io scheduler anticipatory registered (default) 
 +Initializing ths8200_init 
 +Initializing dove_adi9889_init 
 +Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled 
 +serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A 
 +console [ttyS0] enabled 
 +serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A 
 +brd: module loaded 
 +loop: module loaded 
 +Integrated Sata device found 
 +IRQ 21/mvSata: IRQF_DISABLED is not guaranteed on shared IRQs 
 +scsi0 : Marvell SCSI to SATA adapter 
 +scsi1 : Marvell SCSI to SATA adapter 
 +Loading Marvell Ethernet Driver: 
 +  o Cached descriptors in DRAM 
 +  o DRAM SW cache-coherency 
 +  o 2 Giga ports supported 
 +  o Single RX Queue support - ETH_DEF_RXQ=0 
 +  o Single TX Queue support - ETH_DEF_TXQ=0 
 +  o TCP segmentation offload (TSO) supported 
 +  o Large Receive offload (LRO) supported 
 +  o Receive checksum offload supported 
 +  o Transmit checksum offload supported 
 +  o Network Fast Processing (Routing) supported - (Disabled) 
 +  o Driver ERROR statistics enabled 
 +  o Proc tool API enabled 
 +  o SKB Reuse supported - (Disabled) 
 +  o SKB Recycle supported - (Disabled) 
 +  o Rx descripors: q0=128 
 +  o Tx descripors: q0=532 
 +  o Loading network interface(s): 
 +    o register under mv88fx_eth platform 
 +    o egiga0, ifindex = 2, GbE port = 0 
 +Warning: Giga 1 is Powered Off 
 +mvFpRuleDb (c0ee4000): 2048 entries, 8192 bytes 
 +Counter=0, opIdx=6, overhead=16 
 +Counter=1, opIdx=2, overhead=0 
 +Counter=2, opIdx=1, overhead=18 
 +Counter=3, opIdx=2, overhead=0 
 +NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit) 
 +Scanning device for bad blocks 
 +Using static partition definition 
 +Creating 7 MTD partitions on "nand_mtd": 
 +0x000000000000-0x000000100000 : "u-boot" 
 +0x000000100000-0x000000600000 : "uImage" 
 +0x000000600000-0x000000b00000 : "ramdisk" 
 +0x000000b00000-0x000006f00000 : "image" 
 +0x000006f00000-0x000007900000 : "rescue firmware" 
 +0x000007900000-0x000007e00000 : "config" 
 +0x000007e00000-0x000008000000 : "my-dlink" 
 +ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver 
 +ehci_marvell ehci_marvell.70059: Marvell Orion EHCI 
 +ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 
 +ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 
 +ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00 
 +usb usb1: configuration #1 chosen from 1 choice 
 +hub 1-0:1.0: USB hub found 
 +hub 1-0:1.0: 1 port detected 
 +ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver 
 +uhci_hcd: USB Universal Host Controller Interface driver 
 +Initializing USB Mass Storage driver... 
 +usbcore: registered new interface driver usb-storage 
 +USB Mass Storage support registered. 
 +mice: PS/2 mouse device common for all mice 
 +i2c /dev entries driver 
 +md: linear personality registered for level -1 
 +md: raid0 personality registered for level 0 
 +md: raid1 personality registered for level 1 
 +device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com 
 +usbcore: registered new interface driver usbhid 
 +usbhid: v2.6:USB HID core driver 
 +TCP cubic registered 
 +NET: Registered protocol family 17 
 +RPC: Registered udp transport module. 
 +RPC: Registered tcp transport module. 
 +rtc mv_rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800) 
 +md: Waiting for all devices to be available before autodetect 
 +md: If you don't use raid, use raid=noautodetect 
 +md: Autodetecting RAID arrays. 
 +md: Scanned 0 and added 0 devices. 
 +md: autorun ... 
 +md: ... autorun DONE. 
 +RAMDISK: gzip image found at block 0 
 +usb 1-1: new high speed USB device using ehci_marvell and address 2 
 +VFS: Mounted root (ext2 filesystem) on device 1:0. 
 +Freeing init memory: 136K 
 +init started: BusyBox v1.20.2 (2013-11-27 15:54:37 CST) 
 +starting pid 536, tty '': '/etc/rc.sh' 
 +** Mounting /etc/fstab 
 +umount: can't umount /proc: Invalid argument 
 +umount: can't umount /usr/local/modules: Invalid argument 
 +usb 1-1: configuration #1 chosen from 1 choice 
 +scsi2 : SCSI emulation for USB Mass Storage devices 
 +sh: can't open '/usr/sbin/pre_usb.sh' 
 +sh: can't open '/usr/sbin/pre_usb.sh' 
 +first good block is 0 
 +image len = 39366656 , image checksum = b494025d 
 +umount: can't umount /usr/local/tmp: Invalid argument 
 +scsi 2:0:0:0: Direct-Access    Mass    Storage Device  1.00 PQ: 0 ANSI: 0 CCS 
 +sd 2:0:0:0: [sda] 61315072 512-byte logical blocks: (31.3 GB/29.2 GiB) 
 +sd 2:0:0:0: [sda] Write Protect is off 
 +sd 2:0:0:0: [sda] Assuming drive cache: write through 
 +sd 2:0:0:0: [sda] Assuming drive cache: write through 
 + sda: sda1 sda2 
 +sd 2:0:0:0: Attached scsi generic sg0 type 0 
 +sd 2:0:0:0: [sda] Assuming drive cache: write through 
 +sd 2:0:0:0: [sda] Attached SCSI removable disk 
 +dump image checksum=b494025d 
 +mount cmd:busybox mount -t squashfs -o loop /usr/local/tmp/image.cfs /usr/local/modules 
 +ln: /lib/./libnss_dns-2.8.so: File exists 
 +ln: /lib/./libnss_dns.so.2: File exists 
 +ln: /usr/sbin/./system_init: File exists 
 +hardware init 
 +GbE port 0: TxEnable WA - Enabled, deep=1, tx_en_bk=1 
 +mtd check v1.02.08062012 
 +config mtd type is JFFS2 
 +/usr/local/config free size is 4734976 
 +** copy config files 
 +cp: can't stat '/usr/local/config/user.log.old': No such file or directory 
 +usbcore: registered new interface driver usblp 
 +** set loopback interface 
 +old firmware ver:20150728 
 +new firmware ver:20150728 
 +first good block is 0 
 +mac1 = 48:EE:0C:F2:E8:96 
 +lan0:ifconfig egiga0 hw ether 48:EE:0C:F2:E8:96 
 +egiga0: mac address changed 
 +egiga0: link down 
 +egiga0: started 
 +Support Mydlink 
 +egiga0: link up, full duplex, speed 1 Gbps 
 +NET: Registered protocol family 10 
 +lo: Disabled Privacy Extensions 
 +IPv6 over IPv4 tunneling driver 
 +sit0: Disabled Privacy Extensions 
 +ip6tnl0: Disabled Privacy Extensions 
 +IPv4 over IPv4 tunneling driver 
 +tunl0: Disabled Privacy Extensions 
 +net.ipv6.conf.default.accept_dad = 2 
 +net.ipv6.conf.egiga0.accept_dad = 2 
 +net.ipv6.conf.default.dad_transmits = 1 
 +net.ipv6.conf.egiga0.dad_transmits = 1 
 +net.ipv6.conf.default.forwarding = 0 
 +net.ipv6.conf.default.accept_redirects = 1 
 +*** execute rc.init.sh 
 +awk: /var/run/udhcpc0.pid: No such file or directory 
 +udhcpc (v1.20.2) started 
 +Sending discover... 
 +Sending select for 
 +Lease of obtained, lease time 86400 
 +sh: you need to specify whom to kill 
 +deleting routers 
 +route: SIOCDELRT: No such process 
 +call load_module network 
 +RTNETLINK answers: Operation not supported 
 +RTNETLINK answers: Operation not supported 
 +*** set Time Zone **** 
 +Fri Dec 31 22:00:37 GMT 1999 
 +*** get Time from rtc and set it into system **** 
 +rtc: RTC time = 2000/1/1 Sat 2:9:12 
 +Sat Jan  1 02:09:12 GMT 2000 
 +*** Do not adjust RTC time *** 
 +Module IPC SERVER Version:(1.00.20090706) 
 +created mail daemon thread 0 
 +read /usr/local/config/hd_info.xml not exist  
 +/usr/sbin/system_init: line 487: op_server: not found 
 +Starting system message bus 
 +Changing password for messagebus 
 +Password changed. 
 +Command: wget -T5 -t3 -q http://cfaj.freeshell.org/ipaddr.cgi -O /tmp/exip.0 
 +Command: wget -T5 -t3 -q http://icanhazip.com/ -O /tmp/exip.1 
 +/dev/sda1 looks like swapspace - not mounted 
 +mount: you must specify the filesystem type 
 +EXT4-fs (sda2): barriers enabled 
 +kjournald2 starting: pid 1810, dev sda2:8, commit interval 5 seconds 
 +EXT4-fs (sda2): internal journal on sda2:8 
 +EXT4-fs (sda2): delayed allocation enabled 
 +EXT4-fs: file extents enabled 
 +EXT4-fs: mballoc enabled 
 +EXT4-fs (sda2): mounted filesystem with ordered data mode 
 +cp: can't stat '/usr/local/config/Mydlink_Status.xml': No such file or directory 
 +system daemon v1.03.20130707 
 +mcu version 1.02 
 +chk_io v1.03.20130502 
 +killall: chk_hotplug: no process killed 
 +mfg_start version 1.00(2015-07-28) 
 +Sat Jan  1 02:09:31 2000 
 +mnt pnt [/mnt/USB/USB1_a2] 
 +usb_dir [/mnt/USB/USB1_a2] 
 +filename_mfg mfg_DNS_320L 
 +check /mnt/USB/USB1_a2/mfg_DNS_320L file 
 +open  /mnt/USB/USB1_a2/mfg_DNS_320L file failed 
 +cp: can't stat '/usr/local/config/mydlink_time.xml': No such file or directory 
 +opt.local stop ok. 
 +opt.local start ok. 
 +Please press Enter to activate this console. 


Personal Tools