DSM-G600, DNS-3xx and NSA-220 Hack Forum

You must download image_tools.
http://www.msbd.de/image_tools.tgz

This method works, but there is one problem. Kerbel for RevA supports 32MB. RevB has 64MB. Must rebuild the kernel. It's easy. I can tell you how to do it.

Last edited by andry (2009-12-15 11:23:31)

CharminBaer's lenny поддерживает ext3. About NFS do not know.
Not need to download the kernel of kernel.org.
Need to download dlink toolchain:
http://tsd.dlink.com.tw/temp/download/3 … 080723.tgz
unpack dns313v1.01_GPL_20080723.tgz to ~

cd ~/Gmini_????/sourse/kernel/linux
make menuconfig
do not change anything, press exit, press save
make
your kernel will be located arch/arm/boot/zImage
cp ~/Gmini_????/sourse/kernel/linux/arch/arm/boot/zImage ~/zImage_noh
you should add to zImage header:
image_tools/mkimage -f image_tools/kernel_new.cfg -d zImage_noh zImage

copy new zImage and rd.gz rootfs.tgz from to sda/.boot your DNS
check load.
these paths may differ slightly, because I am writing from my memory.
If all is well, you can try to modify the kernel.

For load CharminBaer's lenny you need change "boot" options in kernel.
change /dev/ram0 to /dev/sda3 and change 32M to 64M.
It's work!
Do not add a lot of options simultaneously. add to queue with test load.

Another link to download the toolchain:
ftp://tsd.dlink.com.tw/dns313v1.01_GPL_20080723.tgz

Last edited by andry (2009-12-15 12:59:12)

Your kernel must have support NFS.

check this:
#dmesg | grep -i nfs

As it it is possible patch for loading kernel with /dev/sda3 without kernel recompilation.

It's hard to do without recompiling. You can try to change rd.gz for this.

I have a kernel with Ext3 and NFS for revB. My kernel has the option root=/dev/sda3 instead of root=/dev/ram0.
I also have empty rd.gz and rootfs.tgz.
I can upload my files, if necessary.

usky wrote:

I installer nfs-user-server and not nfs-kernel-server, that don't need a specific kernel (as I understood).

The site http://packages.debian.org/ written that the package nfs-user-server not supported. Recommended to use the package unfs3.

nfs-user-server does not support NFSv3. Your client can connect to the protocol NFSv3. Check it.

usky wrote:

...I did a test with samba... ...I have no writing right on my directory...

[ global ]
....
security = SHARE
....
[ Share ]
comment =
path = /mnt/HD_a2
valid users =
read only = no
guest ok = yes
oplocks = yes
map archive = yes

@andry, what reading speed from your NAS (smb, nfs)?

Thank you both for your help.
Here is what I did :
- I installed Shebby debian
- I installed unfs3
- I did a mount form the client and it was OK.

I did a reboot

Here is the status now ...
- I am not able to connect anymore frome the client.

mount to NFS server '192.168.1.10:/home/laurent' failed: RPC Error: Program not registered

- when I do a  : /etc/init.d/unfs3 restart
I have the following error message :

Restarting unfs3: bind: Address already in use
Couldn't bind to udp port 2049

I had a deep look on google but I did not found any answers ...

HELPPPPPP !!

here is the result :

udp        0      0 192.168.1.10:2049       192.168.1.1:5351        ESTABLISHED

Thank you for your help Andry

Just for your information :
192.168.1.10 is my DNS313
192.168.1.1 is the internet box & the router

Last edited by usky (2009-12-24 14:03:27)

@andry, i also has 100mbs router (dir-320 with firmware from Oleg) and mine hd player is 100mb too. Mine speed about 3-5mbytes per second sbm/nas. Ftp speed is bigger. Sometimes, for large mkv that i watch from nas, network speed is not enough (lagging). So i am looking for solution about speed improvement not enough skills in linux but i am trying

usky wrote:

I found that before the install of mediatomb, everything is OK, after install this is the begining of the troubles...

Make sure your NFS starts before eating mediatomb.
Use update-rc.d to remove and re-add the NFS-server before mediatomb.

One more question .... but this is only to be perfect ;-)
The DNS313 has a directory mounted on the client.
When I copy a file from the client, the associated rights are 700 (rwx only for user).
I would like to have 755 as the default value. Can you tell me how to do ?

All the home folder rights are 755 on the DNS313.
I created a new user (usky) in my case/
The share folder is then /home usky with 755 rights.

I don't know why, but it is ok now ....
Again thanks all for your help.

Last edited by usky (2009-12-26 17:51:31)