DSM-G600, DNS-3xx and NSA-220 Hack Forum

******** UPDATED FEBRUARY 2012 ********

Let me start by saying I am not an Linux expert. I pieced most of this together by googling.

I like to thank all the developers of Debian, SABnzbd, Sickbeard, CouchPotato and Headphone. Without you this would be a pipe dream. I would also like to thank: uli, morgothtdo, danfozzy, cissoubaka, i814u2, mmoedt. Without their help you wouldn't be reading this guide.

I take no responsibly for damaging your NAS, Car, House, Spouse or anything else that can happen.

@@@ YOU MUST HAVE FUN_PLUG INSTALLED AND RUNNING ON THE NAS @@@
You have been WARNED. Let me say it again. You have been WARNED

**** Command Line Syntax ****
To make the command line syntax easier to understand
#=root user state       (#chmod 755 /etc/init.d/sabnzbd)
$=regular user state   ($cd /home/newuser)

*** In the Beginning ***
Debian download file for DNS-320

ftp://ftp.dlink.pl/dns/dns-320/driver_s … 110111.zip

Create a backup of the fun_plug script file that is on the DNS-320
Rename the backup to "fun_plug.bak" and keep it in the same location
This backup is very important so please verify that it was backup

Install prebuilded Debian Squeeze.

From the archive you have already downloaded
(DNS-320&325_linuxDebian_revA_Squeeze_all_en_20110111.zip)
unpack two files:
fun_plug.debian
squeeze.tar.gz
Rename fun_plug.debian to fun_plug
and put them to \\DNS-device\Volume_1 it should be replace the old fun_plug file that you backed up

SSH to the device.
You should get the ffp prompt: /#
Perform the following commands:
# cd /mnt/HD/HD_a2
# gunzip squeeze.tar.gz
# tar -xf squeeze.tar
# ls

Confirm that a directory called "squeeze" has been created and that the new fun_plug is there.

Then shutdown and reboot the device via its WebUI interface.

Now you should have a working Debian Squeeze distribution that can be chrooted during bootup.
After the device is up again, there should be a possibility to connect to the Debian Squeeze installation using SSH.

SSH into your NAS - Login as "root". The default password for this build is "dlink".

ssh root@your.nas.ip

Add updated repos
#nano /etc/apt/sources.list  **Add lines below to file**
   

deb http://security.debian.org/ squeeze/updates main contrib non-free

--- Hit Control o to write file than Control x to exit file ---

#apt-get update
#apt-get upgrade
#passwd

adduser newuser     (newuser = name of new account you will be adding to Debian. So change it to what you want it to be)

Set Time Zone
#dpkg-reconfigure tzdata
#cat /etc/timezone

Set locale settings as follows
#apt-get install locales
#locale-gen en_US en_US.UTF-8
#dpkg-reconfigure locales

Installation of Git and dependency files
#apt-get install git-core
#cd /usr/local/sbin
#chmod 666 /dev/null
#chmod 777 /dev/urandom
#ln -s /dev/urandom /dev/random
#apt-get install python python-cheetah python-configobj python-feedparser python-support par2 python-openssl python-yenc unzip unrar python-dbus sudo
#exit
You should no longer be on SSH as root

Installation SABnzbd
SSH back as newuser (Remember newuser is the account name that you created above) and install Sabnzbd (Current Version 0.6.15 as of this writing)
ssh newuser@your.nas.ip
$cd /home/newuser/
$wget sttp://voxel.dl.sourceforge.net/project/sabnzbdplus/sabnzbdplus/sabnzbd-0.6.15/SABnzbd-0.6.15-src.tar.gz  (Change sttp to http)
$tar xzvf SABnzbd-0.6.15-src.tar.gz
$mv SABnzbd-0.6.15 SABnzbd
$rm SABnzbd-0.6.15-src.tar.gz
$mkdir .sabnzbd
$ls -a (There should be a SABnzbd and .sabzbd listed)

The command below will start Sabnzbd
$python SABnzbd/SABnzbd.py -d -f .sabnzbd/sabnzbd.ini -s your.nas.ip:8080
Allow at least a minute than check your.nas.ip:8080 on your internet browser.
There should be a wizard to setup Sabnzbd. If you don't than you did something wrong go back to installing SABnzbd)

Only install those applications that you want as the NAS has limited resources - Sickbeard (TV Shows) - CouchPotato (Movies) - Headphones (Music)
$git clone git://github.com/midgetspy/Sick-Beard.git
$git clone git://github.com/RuudBurger/CouchPotato.git
$git clone git://github.com/rembo10/headphones.git

The commands below will start each application allow a minute between starts
$python Sick-Beard/SickBeard.py -d (Located on your.nas.ip:8081)
$python CouchPotato/CouchPotato.py -d (Located on your.nas.ip:5000)
$python headphones/Headphones.py -d (Located on your.nas.ip:8181)

At this point all the applications are running on your NAS.

The site below has guides for SABnzbd, Sickbeard, CouchPotato and Headphone.

http://www.ainer.org/sabnzbd-install-se … linux-mint

FYI, when setting up SABnzbd and SickBeard make sure the permissions on the download and show directory are open and recursive.

(i.e chmod 777 -R /mnt/HD/HD_a2/Downloads)


***** Autostarting SABnzbd, Sickbeard, CouchPotato and Headphone *****

SSH as root
#nano /etc/init.d/sabnzbd

Copy text below in the file and remember to replace newuser with the account your created ,{your.nas.ip} with your correct NAS ip and {myapikey} with your SABnzbd api

#!/bin/sh
### BEGIN INIT INFO
# Provides:          SABnzbd
# Required-Start:    $network $remote_fs $syslog
# Required-Stop:     $network $remote_fs $syslog
# Default-Start:     2 3 4 5
# Default-Stop:      0 1 6
# Short-Description: Start SABnzd at boot time
# Description:       Start SABnzbd.
### END INIT INFO

case "$1" in
start)
  echo "Starting SABnzbd."
  /usr/bin/sudo -u root -H /home/newuser/SABnzbd/SABnzbd.py -d -f /home/newuser/.sabnzbd/sabnzbd.ini
;;
stop)
  echo "Shutting down SABnzbd."
  /usr/bin/wget -q --delete-after "http://{your.nas.ip}:8080/sabnzbd/api?mode=shutdown&apikey={myapikey}"
;;
*)
  echo "Usage: $0 {start|stop}"
  exit 1
esac

exit 0

--- Hit Control o to write file than Control x to exit file ---

#chmod 755 /etc/init.d/sabnzbd
#update-rc.d sabnzbd defaults

Add to Boot startup
#nano /boot/linuxrc (add text below to bottom of file)

# START SickBeard CouchPotato Headphone
/etc/init.d/mediaservers.sh

# START SABnzbd
service sabnzbd start

--- Hit Control o to write file than Control x to exit file ---

nano /etc/init.d/mediaservers.sh (Copy text below in file and remember to change newuser)

#!/bin/bash
su root -c "chmod 666 /dev/null"
su newuser -c "python /home/newuser/CouchPotato/CouchPotato.py -d"
su newuser -c "python /home/newuser/Sick-Beard/SickBeard.py -d"
su newuser -c "python /home/newuser/headphones/Headphones.py -d"

--- Hit Control o to write file than Control x to exit file ---

#chmod 755 /etc/init.d/mediaservers.sh
#exit

Restart NAS from Dlink web interface to see if applications autostarted.
(Allow at least 3 mins after complete restart for all applications to be available)


***** Updating SABnzbd *****

Headphones, Sickbeard and Couchpotato have a buildin updater, Sabnzbdplus doesn't.

SSH as newuser  (newuser = name of new account that you created)
Confirm that you are in the right directory and the SABnzbd directory is there
$ls -a

Download and Update SABnzbd - To determine lastest version visit sabnzbd.org (replace the 0.x.x by whatever current version number (ie 0.6.15)
$wget http://voxel.dl.sourceforge.net/project … src.tar.gz

$rm -R SABnzbd
$tar xzvf SABnzbd-0.x.x-src.tar.gz
$mv SABnzbd-0.x.x SABnzbd
$rm SABnzbd-0.x.x-src.tar.gz
$python SABnzbd/SABnzbd.py -d -f .sabnzbd/sabnzbd.ini -s NAS_IP:8080


Please let me know if I can make improvements.

Last edited by Terrabyte (2012-03-11 02:08:45)