DSM-G600, DNS-3xx and NSA-220 Hack Forum

Updating from 3.0 to 3.10 box got bricked - only SYS led is flashing green.
Is there way to reflash it?

reset button works, but i can't stop the box from booting.

I hope, i got serial cable connected right way - front to back |GND|NC|TX|RX|Vcc|

After connecting serial i got this screens

but when i try to skip kernel boot with ESC, nothing happens, just continues booting
------------------------------------------------------------------------------------------------------------------
130976K...OK

DRAM0 Test SUCCESS !

System Memory Mapping
        RAM0: 0x00000000~0x07FFFFFF (128 MB)
        Bootbase: 0x00000000~0x00006547
        Stack: 0x00006548~0x00018D47

Found 28F128J3 at address 0xF8000000
Boot-up Bootext...

Bootext V20081118 | 11/18/2008 20:03:45
Flash Detect....
Found Intel 28F128J3 flash at memory address 0xf8000000

System Memory Mapping
        Flash0: Intel 28F128J3 at 0xF8000000 (16MB; Block0~Block127)
        RAM0: 0x00000000~0x07ffffff (128MB)
        Bootloader: 0x00020000~0x00045783
        Stack: 0x00045784~0x0005d283
        Flash Temp Buffer: 0x07fe0000~0x07ffffff (128KB)
vendername = ZyXEL Communications Corp.
productname = ZyXEL NSA220 PLUS
featurebit [0] [1] = D5 01
MAC = 00 23 F8 07 F5 A5
CountryCode = FF
EngDebugFlag = 01

Hit ESC key to stop boot-up kernel...  1
Squash Root FS...
Boot-up Linux...2.6.18.6

Uncompressing Linux.............................................................
........................................................ done, booting the kerne
l.
Linux version 2.6.18.6 (root@Trinity) (gcc version 3.4.3 (MontaVista 3.4.3-25.0.
70.0501961 2005-12-18)) #1 Tue Dec 30 13:45:20 CST 2008
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ), cr=b0053177
Machine: MV-88fxx81
parse_tag_initrd2: phys_initrd_start->0x2000000 ,phys_initrd_size->0xc00000
Memory policy: ECC disabled, Data cache writeback
check_initrd:initrd_node = 0x0
end_pfn -> 0x8000
node == 0x0, initrd_node = 0x0
initrd_start -> 0xc2000000, initrd_end -> 0xc2c00000

mv_map_io
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists.  Total pages: 32768
Kernel command line: rootfstype=squashfs root=/dev/mtdblock1 ro mtdparts=physmap
-flash.0:2176k(kernel),13184k(initrd),896k(etc),-(bootbase) console=ttyS0,115200
n8 mem=128M init=/linuxrc
--------
init irq----------------------------------------------------------------
boardInfoTbl[0].boardName=ZyXEL-NSA220-DDR1
PID hash table entries: 1024 (order: 10, 4096 bytes)

~~~~ timer init
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 113792KB available (2997K code, 617K data, 120K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs... it is
Freeing initrd memory: 12288K
NET: Registered protocol family 16

-------------------nmv_init--------------------------------------------------
Jackson boardId=00000014
0x10100  1=00820473
0x10100  1=00820473
0x10100  2=00820473
...................mvCpuIfInit
config_device_cs Error : Unknown board

CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size  64MB
PEX0_IO ....base f2000000, size   1MB
PCI0_MEM ....base e4000000, size  64MB
PCI0_IO ....base f2200000, size  64KB
INTER_REGS ....base f1000000, size   1MB
DEVICE_CS0 ....base fa000000, size  16MB
DEVICE_CS1 ....base f0000000, size  16MB
DEVICE_CS2 ....base fb000000, size  16MB
DEV_BOOCS ....base f8000000, size  16MB

  Marvell Development Board (LSP Version 1.10.3_DB_NAS)-- ZyXEL-NSA220-DDR1  Soc
: 88F5182 A2

Detected Tclk 166000000 and SysClk 166666667
Marvell USB EHCI Host controller #0: c2bf4a00
Marvell USB EHCI Host controller #1: c2bf4800
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 4096 bind 2048)
TCP reno registered
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
Done.
init kernel log netlink done
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Marvell Gigabit Ethernet Driver 'egiga':
~~~GPIODOR2 F1010100=00820473
~~~~~~~~~~~~~~SMI2 F1072004=00019140
  o Ethernet descriptors in DRAM
  o DRAM SW cache-coherency
  o Checksum offload enabled
  o Loading network interface 'egiga0'
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~egiga_init_module ok
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
No found HD
----cmdline parser init---
physmap platform flash device: 01000000 at f8000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
4 cmdlinepart partitions found on MTD device physmap-flash.0
Creating 4 MTD partitions on "physmap-flash.0":
0x00000000-0x00220000 : "kernel"
mtd: Giving out device 0 to kernel
0x00220000-0x00f00000 : "initrd"
mtd: Giving out device 1 to initrd
0x00f00000-0x00fe0000 : "etc"
mtd: Giving out device 2 to etc
0x00fe0000-0x01000000 : "bootbase"
mtd: Giving out device 3 to bootbase
ehci_platform ehci_platform.4523: EHCI Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004

usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2

ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 200
4
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v3.0
sl811: driver sl811-hcd, 19 May 2005
usb 1-1: new high speed USB device using ehci_platform and address 2
usb 1-1: configuration #1 chosen from 1 choice
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
VFP support v0.3: not present
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
SQUASHFS error: sb_bread failed reading block 0x332d
SQUASHFS error: Unable to read cache block [ccb4d1:f5b]
SQUASHFS error: Unable to read inode [ccb4d1:f5b]
VFS: Cannot open root device "mtdblock1" or unknown-block(31,1)
Please append a correct "root=" boot option
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,1)


----------------------------------------------------------------------------------------------------------------

ANY HELP PLEASE?

Last edited by slmq (2014-03-29 16:24:47)