Differences

This shows you the differences between the selected revision and the current version of the page.

howto:nut_ups 2008/08/12 03:27 howto:nut_ups 2023/09/07 21:19 current
Line 1: Line 1:
====== NUT (Network UPS Tool) ====== ====== NUT (Network UPS Tool) ======
-Based on information found on the Network UPS Tool website ([[http://networkupstools.org/doc/2.2.0/INSTALL.html]]), these installation instructions were written for Fun_Plug 0.5 and fonz's Network UPS Tools (NUT) version 2.2.2. ([[http://www.inreto.de/dns323/fun-plug/0.5/packages/]])+Instruction for installation of Network UPS Tools (NUT) on fun_plug v 0.5. These instructions are based on information found at the Network UPS Tool website ([[http://networkupstools.org/doc/2.2.0/INSTALL.html]]). 
 + 
 +====== Summary ====== 
 +The primary goal of the Network UPS Tools (NUT) project is to provide reliable monitoring of UPS and PDU hardware and ensure safe shutdowns of the systems which are connected. 
 +We attempt to monitor every kind of UPS and PDU, given sufficient interest. Summary from [[http://networkupstools.org|NUT project page]]. 
===== Getting Started ===== ===== Getting Started =====
-==== What's Needed ==== 
-Successful installation of NUT requires three packages from fonz's site ([[http://www.inreto.de/dns323/fun-plug/0.5/packages/]]). They are;+ 
 + 
 + 
 +==== What's Needed ==== 
 +Successful installation of NUT requires three packages from fonz's website ([[http://www.inreto.de/dns323/fun-plug/0.5/packages/]]). They are;
  * libusb-0.1.12-1.tgz;   * libusb-0.1.12-1.tgz;
  * neon-0.25.5-1.tgz and;   * neon-0.25.5-1.tgz and;
-  * nut-2.2.2-2.tgz+  * nut-2.2.2-3.tgz
-==== How To Get Them ==== 
-Using wget, obtain the three packages identified above and store them in an appropriate directory on your DNS323. The directory I selected to save the files to is named /mnt/HD_a2/Downloads/D-Link/Fun_Plug/NUT. Using the directory of your choice, follow these commands to obtain the files;+=== Assumptions === 
 +DNS323 is operating with Firmware version 1.05 or 1.06 (Installation has not been tested with other firmware versions).
- cd /mnt/HD_a2/Downloads/D-Link/Fun_Plug/NUT+Fun_Plug 0.5 installed and operable.
- wget http://www.inreto.de/dns323/fun-plug/0.5/packages/neon-0.25.5-1.tgz +A functional telnet connection.
- wget http://www.inreto.de/dns323/fun-plug/0.5/packages/libusb-0.1.12-1.tgz +
- wget http://www.inreto.de/dns323/fun-plug/0.5/packages/nut-2.2.2-2.tgz+
-==== How To Install Them ==== 
-The three packages are installed to the appropriate fun_plug directories using the following commands;+ 
 + 
 + 
 + 
 +==== How To Get The Packages ==== 
 +For this example the three packages will be saved to the /mnt/HD_a2/packages directory. Change to this directory by issuing the following command at a telnet prompt; 
 + 
 + cd /mnt/HD_a2/packages 
 + 
 +Use rsync to obtain the three packages and store them in the /mnt/HD_a2/packages directory on your DNS323. Obtain the files by issuing the following commands; 
 + 
 + rsync -av inreto.de::dns323/fun-plug/0.5/packages/neon-0.25.5-1.tgz . 
 + rsync -av inreto.de::dns323/fun-plug/0.5/packages/libusb-0.1.12-1.tgz . 
 + rsync -av inreto.de::dns323/fun-plug/0.5/packages/nut-2.2.2-3.tgz . 
 + 
 + 
 + 
 +==== How To Install The Packages ==== 
 +The packages can be installed from the /mnt/HD_a2/packages directory using the following commands;
funpkg -i neon-0.25.5-1.tgz funpkg -i neon-0.25.5-1.tgz
funpkg -i libusb-0.1.12-1.tgz funpkg -i libusb-0.1.12-1.tgz
- funpkg -i nut-2.2.2-2.tgz+ funpkg -i nut-2.2.2-3.tgz 
 + 
 + 
 +===== Prepare the Environment ===== 
 +Once the packages are downloaded and installed the NUT environment will need to be configured before you'll be able to access and control your UPS. Or should I say your UPS will be able to control your DNS323! Instruction found at the Network UPS Tool website ([[http://networkupstools.org/doc/2.2.0/INSTALL.html]]) advised creation of a Group and a user named ''nutmon''. Creating such allows one to establish a higher level of security on configuration files.
-===== Prepare The UPS Driver Environment ===== 
-Once the packages are downloaded and installed the NUT environment needs to be configured before you'll be able to access and control your UPS. Or should I say your UPS will be able to control your DNS323! 
==== Create User Group ==== ==== Create User Group ====
-For the purposes of this exercise the group will be named nut. At the prompt enter the following command;+For the purposes of this exercise a group named ''nut''will be added. At the prompt enter the following command;
groupadd nut groupadd nut
 +
==== Create User ==== ==== Create User ====
-For the purposes of this exercise the User will be named ups. Create the user and add them to the existing group by entering the following commands at the prompt;+For the purposes of this exercise a user named ''nutmon'' will be created and added to the group named ''nut''. The user is created and added to the existing group by entering the following command;
- adduser -s /bin/false -G nut -H ups+ adduser -s /bin/false -G nut -H nutmon
The system will respond with: The system will respond with:
Line 47: Line 73:
Please use a combination of upper and lower case letters and numbers. Please use a combination of upper and lower case letters and numbers.
-Selected a password for ups then enter it at the New password: and Re-enter new password: prompts.+Selected a password for ''nutmon'' then enter it at the New password: and again at the Re-enter new password: prompts.
 +**Note**
 +  * In this example NUTMonPW is used as the password for a user named ''nutmon''. If you use a different password be sure to include it when configuring the upsd.users file.
----- 
-''Document not formatted beyond this point!''+==== Preserve the Users Password ==== 
 +Each time the DNS323 is booted key files are copied from NVRAM to the /etc directory. When this occurs information pertaining to those Groups and Users added as shown above will be lost. Loss can be prevented by writing group and user information to NVRAM using the store-passwd.sh script.
-Copy sample ups configuration file to the /ffp/etc directory.+ store-passwd.sh
- cp /ffp/etc/ups.conf.sample /ffp/etc/ups.conf+===== Configure and Start NUT Driver =====
-Change ownership of /ffp/etc/ups.conf +==== Create ups.conf File ==== 
- chown root:nut /ffp/etc/ups.conf+During NUT installation sample configuration files were copied to the /ffp/etc directory. These files are identifiable by their ''.sample'' suffix. During this step of the configuration process a ups.conf file will be created from the ups.conf.sample file. This is achieved by copying the sample ups configuration file to the /ffp/etc directory. The command to do so follows;
 + cp /ffp/etc/examples/nut/ups.conf.sample /ffp/etc/ups.conf
-Use favourite editor (I use Notepad++) to establish ups.conf settings.+ 
 +==== Add Driver Configuration Detail ==== 
 +Prior to modifying the ups.conf file you'll need to determine which driver is used with your specific UPS. A UPS hardware compatibility list is located on the [[https://networkupstools.org/stable-hcl.html]] website. Review this list to determine which driver is required for your specific application. Please note these instructions pertain specifically to USB connected UPS.  
 + 
 +Use your favourite editor (I use Notepad++) to open the ups.conf file, enter and subsequently save your specific settings.
An APC Back-UPS RS 900 is connected to the USB port on my DNS323. Settings for this device would be; An APC Back-UPS RS 900 is connected to the USB port on my DNS323. Settings for this device would be;
Line 72: Line 105:
desc = "Back-UPS RS 900" desc = "Back-UPS RS 900"
-A UPS hardware compatibility list is located at http://networkupstools.org/compat/stable.html +==== Driver Startup ==== 
-  +Start the NUT driver. This is accomplished by issuing the following command;
-  +
-Change ownership of /ffp/var/state/ups directory +
- +
- chmod 0770 /ffp/var/state/ups +
- chown root:nut /ffp/var/state/ups +
- +
- +
------ Startup ----- +
- +
-Start the driver for your hardware.+
- # /ffp/bin/upsdrvctl -t -u ups start+ upsdrvctl start
Make sure the driver doesn't report any errors.  It should show a few details about the hardware and then enter the background. You should get back to the command prompt a few seconds later.  For reference, a successful start of the usbhid-ups driver looks like this: Make sure the driver doesn't report any errors.  It should show a few details about the hardware and then enter the background. You should get back to the command prompt a few seconds later.  For reference, a successful start of the usbhid-ups driver looks like this:
- 
Network UPS Tools - UPS driver controller 2.2.2 Network UPS Tools - UPS driver controller 2.2.2
Line 94: Line 116:
Using subdriver: APC HID 0.92 Using subdriver: APC HID 0.92
-If the driver doesn't start cleanly, make sure you have picked the right one for your hardware.  You might need to try other drivers by changing the "driver=" value in ups.conf.+If the driver doesn't start cleanly, make sure you have picked the right one for your hardware.  You might need to try other drivers by changing the "driver=" value in ups.conf file.
Be sure to check the driver's man page to see if it needs any extra settings in ups.conf to detect your hardware. Be sure to check the driver's man page to see if it needs any extra settings in ups.conf to detect your hardware.
Line 100: Line 122:
If it says "can't bind /var/state/ups/..." or similar, then your state path probably isn't writable by the driver.  Check the permissions and mode on that directory. If it says "can't bind /var/state/ups/..." or similar, then your state path probably isn't writable by the driver.  Check the permissions and mode on that directory.
 +===== Configure and Start Network Server =====
 +==== Configure Host Access List ====
 +=== Create upsd.conf File ===
 +During this step of the configuration process a upsd.conf file will be created from the upsd.conf.sample file. This is achieved by copying the sample upsd configuration file to the /ffp/etc directory. The command to do so follows;
------ Configuration Process -----+ cp /ffp/etc/examples/nut/upsd.conf.sample /ffp/etc/upsd.conf
-Basic configuration of upsd requires copying the sample configuration file to the /ffp/etc directory.+=== Configuring Specific Host Settings === 
 +Configuring access by a specific host requires modification of the upsd.conf file. For this example it will be necessary to add a host named DNS323 on IP 192.168.1.50 to the server configuration file. Doing so will permit optimum configuration of the monitor tool. Use your favourite editor to open the upsd.conf file, enter and subsequently save the following lines;
- cp /ffp/etc/upsd.conf.sample /ffp/etc/upsd.conf+ ACL DNS323 192.168.1.50/32 
 +  
 + ACCEPT DNS323
-Configuring a specific host requires modification of the upsd.conf file. For example, to add a host named DNS323_NAS on IP 192.168.1.50 the following lines need to be added to the upsd.conf file;+==== Configuration User Access List ==== 
 +=== Create upsd.users File === 
 +During this step of the configuration process a upsd.users file will be created from the upsd.users.sample file. This is achieved by copying the sample upsd configuration file to the /ffp/etc directory. The command to do so follows;
- ACL DNS323_NAS 192.168.1.50/32+ cp /ffp/etc/examples/nut/upsd.users.sample /ffp/etc/upsd.users
- ACCEPT DNS323_NAS+=== Configuring an Administrative User === 
 +Use your favourite editor to open the upsd.users file, enter and subsequently save your specific settings.
- + [nutmon] 
- + password = NUTMonPW 
-Copy sample user configuration file to the /ffp/etc directory. + allowfrom = localhost
- +
- cp /ffp/etc/upsd.users.sample /ffp/etc/upsd.users +
- +
- +
-Use favourite editor (I use Notepad++) to establish upsd.users settings. +
- +
- [ups] +
- password = +
- allowfrom = localhost DNS323_NAS+
actions = SET actions = SET
instcmds = ALL instcmds = ALL
-  +While we're at it let's create an entry for monitoring tool.
-  +
-Do not make either of the upsd files (upsd.conf or upsd.users) world-readable. Since they both hold access control data and passwords they just need to be readable by the user you created in the preparation process.+
-The suggested configuration is to chown it to root, chgrp it to the group you created, then make it readable by the group.+ [monuser] 
 + password = MonUserPW 
 + allowfrom = DNS323 
 + upsmon master
- cd /ffp/etc +==== Network Server Startup ==== 
- chown root:nut upsd.conf upsd.users +Start the network server. This is accomplished by issuing the following command;
- chmod 0640 upsd.conf upsd.users+
-  + upsd
-  +
-Start the network server.+
- # /ffp/sbin/upsd -u ups+The Network Server can be stopped by issuing an ''upsd -c stop'' command.
-(To stop the network server use /ffp/sbin/upsd -u ups -c stop) 
-Make sure that the UPS is providing good status data.+==== UPS and Server Status Check ==== 
 +Make sure that the UPS is providing good status data by issuing the following command;
- # /ffp/bin/upsc APC_UPS@localhost ups.status or+ upsc APC_UPS@localhost ups.status
-Look at all of the status data which is being monitored.+If all is okay then ''OL'' (On-line) should appear after the upsc command is issued. If the unit running is On-Battery you would see ''OB'' and if charging you would see ''OC''.
- /ffp/bin/upsc APC_UPS@localhost 
-What happens now depends on the kind of UPS and driver you have.In the list, you should see ups.status with the same value you got above.  A sample run on an APC Back-UPS RS 900 looks like this:+The upsc command is also used to look at all status that is being monitored. Look at all of the status data by issuing the following command;
-battery.charge: 100 + upsc APC_UPS@localhost
-battery.charge.low: 10 +
-battery.charge.warning: 50 +
-battery.date: 2001/09/25 +
-battery.mfr.date: 2008/06/05 +
-battery.runtime: 2025 +
-battery.runtime.low: 120 +
-battery.temperature: 3022999999999998800 +
-battery.type: PbAc +
-battery.voltage: 27.8 +
-battery.voltage.nominal: 24.0 +
-driver.name: usbhid-ups +
-driver.parameter.pollfreq: 30 +
-driver.parameter.pollinterval: 2 +
-driver.parameter.port: auto +
-driver.version: 2.2.2 +
-driver.version.data: APC HID 0.92 +
-driver.version.internal: 0.33 +
-input.voltage: 122.0 +
-input.voltage.nominal: 120 +
-output.voltage: 120.0 +
-output.voltage.nominal: 120.0 +
-ups.beeper.status: enabled +
-ups.delay.shutdown: 20 +
-ups.delay.start: 30 +
-ups.firmware: 9.o2 .D +
-ups.firmware.aux: o2 +
-ups.load: 229999999999999940000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000000 +
-ups.mfr: American Power Conversion +
-ups.mfr.date: 2007/10/24 +
-ups.model: Back-UPS RS 900 +
-ups.productid: 0002 +
-ups.serial: 5B0743U08220 +
-ups.status: OL +
-ups.test.result: No test initiated +
-ups.timer.reboot: 0 +
-ups.timer.shutdown: -1 +
-ups.vendorid: 051d+
 +What happens now depends on the kind of UPS and driver you have. In the list that follows is sample data from an APC Back-UPS RS 900.
------ Configure Monitor -----+ battery.charge: 100 
 + battery.charge.low: 10 
 + battery.charge.warning: 50 
 + battery.date: 2001/09/25 
 + battery.mfr.date: 2008/06/05 
 + battery.runtime: 2535 
 + battery.runtime.low: 120 
 + battery.temperature: 29.2 
 + battery.type: PbAc 
 + battery.voltage: 27.8 
 + battery.voltage.nominal: 24.0 
 + device.mfr: American Power Conversion 
 + device.model: Back-UPS RS 900 
 + device.serial: 5B0743U08220 
 + device.type: ups 
 + driver.name: usbhid-ups 
 + driver.parameter.pollfreq: 30 
 + driver.parameter.pollinterval: 2 
 + driver.parameter.port: AUTO 
 + driver.version: 2.4.1 
 + driver.version.data: APC HID 0.93 
 + driver.version.internal: 0.34 
 + input.voltage: 122.0 
 + input.voltage.nominal: 120 
 + output.voltage: 120.0 
 + output.voltage.nominal: 120.0 
 + ups.beeper.status: enabled 
 + ups.delay.shutdown: 20 
 + ups.firmware: 9.o2 .D 
 + ups.firmware.aux: o2 
 + ups.load: 18.0 
 + ups.mfr: American Power Conversion 
 + ups.mfr.date: 2007/10/24 
 + ups.model: Back-UPS RS 900 
 + ups.productid: 0002 
 + ups.serial: 5B0743U08220 
 + ups.status: OL 
 + ups.test.result: No test initiated 
 + ups.timer.reboot: 0 
 + ups.timer.shutdown: -1 
 + ups.vendorid: 051d
-Create user and add to existing group. For the purposes of this exercise the user will be named nutmon+===== Configure and Start Monitor ===== 
 +==== Create upsmon.conf File ==== 
 +During this step of the configuration process a upsmon.conf file will be created from the upsmon.conf.sample file. This is achieved by copying the sample upsmon configuration file to the /ffp/etc directory. The command to do so follows;
- adduser -s /bin/false -G nut -H -D nutmon+ cp /ffp/etc/examples/nut/upsmon.conf.sample /ffp/etc/upsmon.conf
 +==== Configure a RUN_AS_USER ====
 +Use your favourite editor to open the upsmon.conf file and edit line 30 so that it reads;
 + RUN_AS_USER nutmon
 +instead of;
-Create a user for the monitor+ # RUN_AS_USER nutmon
- adduser -s /bin/false -G nut -H monuser 
-The system will respond with:+==== Configure a MONITOR User ==== 
 +With the the upsmon.conf file still open in your editor add the following at line 85;
- Changing password for monuser + MONITOR APC_UPS@DNS323 1 monuser MonUserPW master
- Enter the new password (minimum of 5, maximum of 8 characters) +
- Please use a combination of upper and lower case letters and numbers.+
-Selected a password for ups then enter it at the New password: and Re-enter new password: prompts.+**Note** 
 +  * APC_UPS is the name of the UPS as it was set in the ups.conf file. 
 +  * MonUserPW is the password that was established when ''monuser'' was added to the upsd.users file. If you used a different password, which you should, be sure to replace MonUserPW with the password that you set in the upsd.users file. 
 +  * DNS323 is the host name that was established when configuring the upsd.conf file.
 +==== Monitor Startup ====
 +Start the upsmon Monitor. This is accomplished by issuing the following command;
-Copy sample monitor configuration file to the /ffp/etc directory.+ upsmon
- cp /ffp/etc/upsmon.conf.sample /ffp/etc/upsmon.conf 
-Use favourite editor (I use Notepad++) to establish upsmon.conf settings. 
-Do not make the upsmon.conf files world-readable. Since this file holds access control data and passwords it just needs to be readable by the user you created in the preparation process.+====== Increase File and Directory Security ====== 
 +Many of NUT's configuration files contain sensitive data; user names and passwords. To guard against inappropriate access of this information restricting access to users belonging to the ''nut'' group is recommended. This is achieved through the following commands;
-The suggested configuration is to chown it to root, chgrp it to the group you created, then make it readable by the group.+ chown root:nut /ffp/etc/ups.conf /ffp/etc/upsd.conf /ffp/etc/upsd.users /ffp/etc/upsmon.conf 
 + chmod 0640 /ffp/etc/ups.conf /ffp/etc/upsd.conf /ffp/etc/upsd.users /ffp/etc/upsmon.conf
- chmod 0640 upsmon.conf +It will also be necessary to change ownership of /ffp/var/state/ups directory. This is achieved through the following commands;
- chown root:nut upsmon.conf+
 + chown root:nut /ffp/var/state/ups
 + chmod 0770 /ffp/var/state/ups
-Configure upsd to recognize upsmon. 
-First create an ACL in upsd.conf for the host that will be running upsmon.  Then use it in an ACCEPT line to allow that host to monitor the UPS.  This will let upsmon connect to upsd. 
-Assuming a host called DNS323_NAS with the IP address of 192.168.1.50, the additional configuration items would look like this: 
- ACL mybox 192.168.1.50/32 
- ACCEPT DNS323_NAS 
-  
-Start the upsmon monitor.+====== Automating the Startup Process ====== 
 +You can Telnet to the DNS323 each time you want to start NUT or use a startup script. The following can be added to a nut.sh script file and stored in the /ffp/start directory by copying the content of the code box into your favourite editor then saving the resultant file as /ffp/start/nut.sh.
- # /ffp/sbin/upsmon -u monuser+Use this script for DNS323 firmware versions prior to 1.07.
 + #!/ffp/bin/sh
 +
 + # PROVIDE: nut
 +
 + . /ffp/etc/ffp.subr
 +
 + name="nut"
 + start_cmd="nut_start"
 + stop_cmd="nut_stop"
 +
 + nut_start()
 + {
 + # Start NUT driver for UPS hardware.
 + /ffp/bin/upsdrvctl start
 +
 + # Start NUT Network Server
 + /ffp/sbin/upsd
 +
 + # Start NUT monitor agent
 + /ffp/sbin/upsmon -u monuser
 + }
 +
 + nut_stop()
 + {
 + # Stop NUT monitor agent
 + /ffp/sbin/upsmon -c stop
 +
 + # Stop NUT Network Server
 + /ffp/sbin/upsd -c stop
 +
 + # Stop NUT driver for UPS hardware.
 + /ffp/bin/upsdrvctl stop
 + }
 +
 + run_rc_command "$1"
 +Use this script for DNS323 firmware version 1.07.
------ Installing WinNUT -----+ #!/ffp/bin/sh 
 +  
 + # PROVIDE: nut 
 +  
 + . /ffp/etc/ffp.subr 
 +  
 + name="nut" 
 + start_cmd="nut_start" 
 + stop_cmd="nut_stop" 
 +  
 + nut_start() 
 + { 
 + ##################### 
 + # We're using NUT UPS from ffp; # 
 + ##################### 
 +  
 + ############################################ 
 + # Stop built in NUT UPS deamons in preparation for starting ffp NUT UPS # 
 + ############################################ 
 + if ps | grep /usr/local/ups/bin/usbhid-ups | grep -v grep 
 + then 
 + echo "* Stopping Default UPS Services" 
 + # Stop NUT Network Server 
 + /sys/crfs/sbin/upsd -c stop 
 +  
 + # Stop NUT driver for UPS hardware. 
 + /sys/crfs/sbin/upsdrvctl stop 
 + fi 
 +  
 + sleep 2 
 +  
 + ############## 
 + # Start ffp NUT UPS # 
 + ############## 
 + # Start NUT driver for UPS hardware. 
 + /ffp/bin/upsdrvctl start 
 +  
 + # Start NUT Network Server 
 + /ffp/sbin/upsd 
 +  
 + # Start NUT monitor agent 
 + /ffp/sbin/upsmon -u monuser 
 + } 
 +  
 + nut_stop() 
 + { 
 + # Stop NUT monitor agent 
 + /ffp/sbin/upsmon -c stop 
 +  
 + # Stop NUT Network Server 
 + /ffp/sbin/upsd -c stop 
 +  
 + # Stop NUT driver for UPS hardware. 
 + /ffp/bin/upsdrvctl stop 
 + } 
 +  
 + run_rc_command "$1"
-Create a user for WinNUT Monitoring Tool+Don't forget to make it runnable:
- adduser -s /bin/false -G nut -H winnmonuser+ chmod a+x /ffp/start/nut.sh
-The system will respond with:+====== Add UPS Monitoring and Shut Down Capability to A Remote Windows Machine ====== 
 +If you have a Windows PC connected to the same UPS then a Windows Application named WinNUT may be of interest to you. See [[http://csociety.ecn.purdue.edu/~delpha/winnut/|WinNUT]] for details.
- Changing password for winnmonuser 
- Enter the new password (minimum of 5, maximum of 8 characters) 
- Please use a combination of upper and lower case letters and numbers. 
-Selected a password for ups then enter it at the New password: and Re-enter new password: prompts.+==== Configuring the NUT Environment for Use With WinNUT ==== 
 +For WinNUT to run successfully it will be necessary to add user information to the upsd.users and host information to the upsd.conf files located on the DNS323.
 +=== Add a Remote Monitoring User  ===
 +Use your favourite editor to open the upsd.users file, enter and subsequently save your specific settings.
-===== Preserving Passwords =====+ [winmonuser] 
 + password = WinMonUserPW 
 + allowfrom = Remote-PC 
 + upsmon slave
-Each time the DNS323 is booted key files are copied from NVRAM to the /etc directory. When this occurs information pertaining to those Groups and Users added as shown above will be lost. Loss can be prevented by writing group and user information to NVRAM using the store-passwd.sh script.+=== Configuring Remote Host Settings === 
 +Configuring access for the remote host requires modification of the upsd.conf file. For this example it will be necessary to add a host named Remote-PC on IP 192.168.1.200 to the server configuration file. Use your favourite editor to open the upsd.conf file, enter and subsequently save the following lines;
- store-passwd.sh+ ACL DNS323 192.168.1.200/32 
 +  
 + ACCEPT Remote-PC 
 + 
 +If the NUT Server is running when this change is made it will be necessary to reload the configuration file. This can be done by issuing the following command;
 + upsd -reload

Navigation
[Edit]
Personal Tools