Instruction for installation of Network UPS Tools (NUT) on fun_plug v 0.5. These instructions are based on information found at the Network UPS Tool website (http://networkupstools.org/doc/2.2.0/INSTALL.html).

A DNS323 with Fun_Plug 0.5 installed.

A functional telnet connection.

Successful installation of NUT requires three packages from fonz's website (http://www.inreto.de/dns323/fun-plug/0.5/packages/). They are;

• libusb-0.1.12-1.tgz;
• neon-0.25.5-1.tgz and;
• nut-2.2.2-2.tgz

For this example the three packages will be saved to the /mnt/HD_a2/packages directory. Change to this directory by issuing the following command at a telnet prompt;

cd /mnt/HD_a2/packages

Use rsync to obtain the three packages and store them in the /mnt/HD_a2/packages directory on your DNS323. Obtain the files by issuing the following commands;

rsync -av inreto.de::dns323/fun-plug/0.5/packages/neon-0.25.5-1.tgz .
rsync -av inreto.de::dns323/fun-plug/0.5/packages/libusb-0.1.12-1.tgz .
rsync -av inreto.de::dns323/fun-plug/0.5/packages/nut-2.2.2-2.tgz .

The packages can be installed from the /mnt/HD_a2/packages directory using the following commands;

funpkg -i neon-0.25.5-1.tgz
funpkg -i libusb-0.1.12-1.tgz
funpkg -i nut-2.2.2-2.tgz

Once the packages are downloaded and installed the NUT environment will need to be configured before you'll be able to access and control your UPS. Or should I say your UPS will be able to control your DNS323! Instruction found at the Network UPS Tool website (http://networkupstools.org/doc/2.2.0/INSTALL.html) advised creation of a Group and a user named nutmon. Creating such allows one to establish a higher level of security on configuration files.

For the purposes of this exercise a group named nutwill be added. At the prompt enter the following command;

groupadd nut

For the purposes of this exercise a user named nutmon will be created and added to the group named nut. The user is created and added to the existing group by entering the following command;

adduser -s /bin/false -G nut -H nutmon

The system will respond with:

Changing password for ups
Enter the new password (minimum of 5, maximum of 8 characters)
Please use a combination of upper and lower case letters and numbers.

Selected a password for nutmon then enter it at the New password: and again at the Re-enter new password: prompts.

Note

• In this example NUTMonPW is used as the password for a user named nutmon. If you use a different password be sure to include it when configuring the upsd.users file.

Each time the DNS323 is booted key files are copied from NVRAM to the /etc directory. When this occurs information pertaining to those Groups and Users added as shown above will be lost. Loss can be prevented by writing group and user information to NVRAM using the store-passwd.sh script.

store-passwd.sh

During NUT installation sample configuration files were copied to the /ffp/etc directory. These files are identifiable by their .sample suffix. During this step of the configuration process a ups.conf file will be created from the ups.conf.sample file. This is achieved by copying the sample ups configuration file to the /ffp/etc directory. The command to do so follows;

cp /ffp/etc/ups.conf.sample /ffp/etc/ups.conf

Prior to modifying the ups.conf file you'll need to determine which driver is used with your specific UPS. A UPS hardware compatibility list is located on the Network UPS Tools website. Review this list to determine which driver is required for your specific application. Please note these instructions pertain specifically to USB connected UPS.

Use your favourite editor (I use Notepad++) to open the ups.conf file, enter and subsequently save your specific settings.

An APC Back-UPS RS 900 is connected to the USB port on my DNS323. Settings for this device would be;

[APC_UPS]
	driver = usbhid-ups
	port = USB
	desc = "Back-UPS RS 900"

Start the NUT driver. This is accomplished by issuing the following command;

upsdrvctl start

Make sure the driver doesn't report any errors. It should show a few details about the hardware and then enter the background. You should get back to the command prompt a few seconds later. For reference, a successful start of the usbhid-ups driver looks like this:

Network UPS Tools - UPS driver controller 2.2.2
Network UPS Tools: 0.29 USB communication driver - core 0.33 (2.2.2)
Using subdriver: APC HID 0.92

If the driver doesn't start cleanly, make sure you have picked the right one for your hardware. You might need to try other drivers by changing the “driver=” value in ups.conf file.

Be sure to check the driver's man page to see if it needs any extra settings in ups.conf to detect your hardware.

If it says “can't bind /var/state/ups/…” or similar, then your state path probably isn't writable by the driver. Check the permissions and mode on that directory.

During this step of the configuration process a upsd.conf file will be created from the upsd.conf.sample file. This is achieved by copying the sample upsd configuration file to the /ffp/etc directory. The command to do so follows;

cp /ffp/etc/upsd.conf.sample /ffp/etc/upsd.conf

Configuring access by a specific host requires modification of the upsd.conf file. For this example it will be necessary to add a host named DNS323 on IP 192.168.1.50 to the server configuration file. Doing so will permit optimum configuration of the monitor tool. Use your favourite editor to open the upsd.conf file, enter and subsequently save the following lines;

ACL DNS323 192.168.1.50/32

ACCEPT DNS323

During this step of the configuration process a upsd.users file will be created from the upsd.users.sample file. This is achieved by copying the sample upsd configuration file to the /ffp/etc directory. The command to do so follows;

cp /ffp/etc/upsd.users.sample /ffp/etc/upsd.users

Use your favourite editor to open the upsd.users file, enter and subsequently save your specific settings.

[nutmon]
	password = NUTMonPW
	allowfrom = localhost
	actions = SET
	instcmds = ALL

While we're at it let's create an entry for monitoring tool.

[monuser]
	password = MonUserPW
	allowfrom = DNS323
	upsmon master

Start the network server. This is accomplished by issuing the following command;

upsd

The Network Server can be stopped by issuing an upsd -c stop command.

Make sure that the UPS is providing good status data by issuing the following command;

upsc APC_UPS@localhost ups.status

If all is okay then OL (On-line) should appear after the upsc command is issued. If the unit running is On-Battery you would see OB and if charging you would see OC.

The upsc command is also used to look at all status that is being monitored. Look at all of the status data by issuing the following command;

upsc APC_UPS@localhost

What happens now depends on the kind of UPS and driver you have. In the list that follows is sample data from an APC Back-UPS RS 900.

battery.charge: 100
battery.charge.low: 10
battery.charge.warning: 50
battery.date: 2001/09/25
battery.mfr.date: 2008/06/05
battery.runtime: 2025
battery.runtime.low: 120
battery.temperature: 3022999999999998800
battery.type: PbAc
battery.voltage: 27.8
battery.voltage.nominal: 24.0
driver.name: usbhid-ups
driver.parameter.pollfreq: 30
driver.parameter.pollinterval: 2
driver.parameter.port: auto
driver.version: 2.2.2
driver.version.data: APC HID 0.92
driver.version.internal: 0.33
input.voltage: 122.0
input.voltage.nominal: 120
output.voltage: 120.0
output.voltage.nominal: 120.0
ups.beeper.status: enabled
ups.delay.shutdown: 20
ups.delay.start: 30
ups.firmware: 9.o2 .D
ups.firmware.aux: o2
ups.load:22999999999999994
ups.mfr: American Power Conversion
ups.mfr.date: 2007/10/24
ups.model: Back-UPS RS 900
ups.productid: 0002
ups.serial: 5B0743U08220
ups.status: OL
ups.test.result: No test initiated
ups.timer.reboot: 0
ups.timer.shutdown: -1
ups.vendorid: 051d

During this step of the configuration process a upsmon.conf file will be created from the upsmon.conf.sample file. This is achieved by copying the sample upsmon configuration file to the /ffp/etc directory. The command to do so follows;

cp /ffp/etc/upsmon.conf.sample /ffp/etc/upsmon.conf

Use your favourite editor to open the upsmon.conf file and edit line 30 so that it reads;

RUN_AS_USER nutmon

instead of;

# RUN_AS_USER nutmon

With the the upsmon.conf file still open in your editor add the following at line 85;

MONITOR APC_UPS@DNS323 1 monuser MonUserPW master

Note

• APC_UPS is the name of the UPS as it was set in the ups.conf file.
• MonUserPW is the password that was established when monuser was added to the upsd.users file. If you used a different password, which you should, be sure to replace MonUserPW with the password that you set in the upsd.users file.
• DNS323 is the host name that was established when configuring the upsd.conf file.

Start the upsmon Monitor. This is accomplished by issuing the following command;

upsmon -u monuser

Many of NUT's configuration files contain sensitive data; user names and passwords. To guard against inappropriate access of this information restricting access to users belonging to the nut group is recommended. This is achieved through the following commands;

chown root:nut /ffp/etc/ups.conf /ffp/etc/upsd.conf /ffp/etc/upsd.users /ffp/etc/upsmon.conf
chmod 0640 /ffp/etc/ups.conf /ffp/etc/upsd.conf /ffp/etc/upsd.users /ffp/etc/upsmon.conf

It will also be necessary to change ownership of /ffp/var/state/ups directory. This is achieved through the following commands;

chown root:nut /ffp/var/state/ups
chmod 0770 /ffp/var/state/ups

If you have a Windows PC connected to the same UPS then the utility named WinNUT will be of interest to you.

WinNUT

Create a user for WinNUT Monitoring Tool

adduser -s /bin/false -G nut -H winnmonuser

The system will respond with:

Changing password for winnmonuser
Enter the new password (minimum of 5, maximum of 8 characters)
Please use a combination of upper and lower case letters and numbers.

Selected a password for ups then enter it at the New password: and Re-enter new password: prompts.