DSM-G600, DNS-3xx and NSA-220 Hack Forum
Unfortunately no one can be told what fun_plug is - you have to see it for yourself.
You are not logged in.
Announcement
• DSM-G600: Wiki - Main Page |
Downloads |
SVN
•
DNS-323: Wiki |
Downloads
•
IRC Channel #funplug on irc.freenode.org
IRC Channel #funplug on irc.freenode.org
Pages: 1
- Index
- » DNS-323/321 Discussion
- » Native Debian without flashing the firmware - instructions and issues
#1 2010-03-05 21:18:32
- juhog
- Member
- Registered: 2010-03-05
- Posts: 9
Native Debian without flashing the firmware - instructions and issues
Hello everyone.
I have been experimenting with ffp-reloaded and Debian. My goal has been to run native Debian installation without flashing the firmware. The motivation to this is to avoid effectively bricking the device, as I, like most of the other users of this device, don't have serial connection available.
I have successfully installed Debian using the kernel and the initial ramdisk that I extracted from the debian-installer firmware file (netboot.img). The installer ran flawlessly, so I suppose that ffp-reloaded should be able to handle recent Debian kernels without any problems.
Booting to the installation with ffp-reloaded works as well. Everything seems to work, so my initial goal of installing and booting Debian natively and not flashing the device is fulfilled.
There is one problem though: whilst booting to Debian with kernel 2.6.26-2-orion5x works, kernel 2.6.32-orion5x is unusable. This is a major problem since newer kernel has many improvements over the older one, and of course, it would be really great if one could update the kernel as newer versions get released.
The problem with kernel 2.6.32-orion5x is that the ethernet connection does not work. I do not know why, but at least for me that is the case. My router seems to be able to assign an address to the device as I can see it in the status page of my router's web administration interface, but connecting to the device is impossible. I tried it in both 100M and 1000M networks, no difference. Observing the logs does not help much either as for me it seems as if eth0 is in working condition and the device will register plugging and unplugging the network cable. The log states though that the device is not able to connect to the DHCP server. I assigned static IP to the device and tried again, but even then the connection did not work. Of course the log did not complain about anything anymore, since it didn't try to fetch DHCP address anymore.
I have not tried any other kernel versions yet, so I do not know if the problem is limited to this single kernel version or not. Furthermore I cannot verify what is causing the problem; the kernel, ffp-reloaded or my hardware. I am also unable to test if the kernel would work flawlessly if I flashed it to the firmware. I am currently on vacation and don't have access to my DNS-323, so further testing from my part won't happen until late next week. It would be great if some people around here could do some testing and see if they can reproduce the same problem. I guess people that have access to serial console can do quite effective debugging, so help from those people would be much appreciated! 
Hopefully the problem isn't anything too hard to fix, and can be fixed, for example, by altering the kernel configs.
syslog with kernel 2.6.26-2-orion5x:
Code:
Mar 5 11:47:43 dns-siika kernel: imklog 3.18.6, log source = /proc/kmsg started. Mar 5 11:47:43 dns-siika kernel: [ 0.000000] Initializing cgroup subsys cpu Mar 5 11:47:43 dns-siika kernel: [ 0.000000] Linux version 2.6.26-2-orion5x (Debian 2.6.26-21lenny3) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 Fri Feb 12 01:56:06 UTC 2010 Mar 5 11:47:43 dns-siika kernel: [ 0.000000] CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177 Mar 5 11:47:43 dns-siika kernel: [ 0.000000] Machine: D-Link DNS-323 Mar 5 11:47:43 dns-siika kernel: [ 0.000000] Memory policy: ECC disabled, Data cache writeback Mar 5 11:47:43 dns-siika kernel: [ 0.000000] On node 0 totalpages: 16384 Mar 5 11:47:43 dns-siika kernel: [ 0.000000] DMA zone: 128 pages used for memmap Mar 5 11:47:43 dns-siika kernel: [ 0.000000] DMA zone: 0 pages reserved Mar 5 11:47:43 dns-siika kernel: [ 0.000000] DMA zone: 16256 pages, LIFO batch:3 Mar 5 11:47:43 dns-siika kernel: [ 0.000000] Normal zone: 0 pages used for memmap Mar 5 11:47:43 dns-siika kernel: [ 0.000000] Movable zone: 0 pages used for memmap Mar 5 11:47:43 dns-siika kernel: [ 0.000000] CPU0: D VIVT write-back cache Mar 5 11:47:43 dns-siika kernel: [ 0.000000] CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets Mar 5 11:47:43 dns-siika kernel: [ 0.000000] CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets Mar 5 11:47:43 dns-siika kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Mar 5 11:47:43 dns-siika kernel: [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda3 rootdelay=10 ip=192.168.0.179::192.168.0.1:255.255.255.0:dns-siika:eth0:none Mar 5 11:47:43 dns-siika kernel: [ 0.000000] PID hash table entries: 256 (order: 8, 1024 bytes) Mar 5 11:47:43 dns-siika kernel: [42949372.960000] Console: colour dummy device 80x30 Mar 5 11:47:43 dns-siika kernel: [42949372.960000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Mar 5 11:47:43 dns-siika kernel: [42949372.960000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Mar 5 11:47:43 dns-siika kernel: [42949372.960000] Memory: 64MB = 64MB total Mar 5 11:47:43 dns-siika kernel: [42949372.960000] Memory: 59384KB available (2564K code, 358K data, 116K init) Mar 5 11:47:43 dns-siika kernel: [42949372.960000] Calibrating delay loop... 332.59 BogoMIPS (lpj=1662976) Mar 5 11:47:43 dns-siika kernel: [42949373.180000] Security Framework initialized Mar 5 11:47:43 dns-siika kernel: [42949373.180000] SELinux: Disabled at boot. Mar 5 11:47:43 dns-siika kernel: [42949373.180000] Capability LSM initialized Mar 5 11:47:43 dns-siika kernel: [42949373.180000] Mount-cache hash table entries: 512 Mar 5 11:47:43 dns-siika kernel: [42949373.180000] Initializing cgroup subsys ns Mar 5 11:47:43 dns-siika kernel: [42949373.180000] Initializing cgroup subsys cpuacct Mar 5 11:47:43 dns-siika kernel: [42949373.180000] Initializing cgroup subsys devices Mar 5 11:47:43 dns-siika kernel: [42949373.180000] CPU: Testing write buffer coherency: ok Mar 5 11:47:43 dns-siika kernel: [42949373.180000] net_namespace: 652 bytes Mar 5 11:47:43 dns-siika kernel: [42949373.180000] NET: Registered protocol family 16 Mar 5 11:47:43 dns-siika kernel: [42949373.180000] Orion ID: MV88F5182-A2. TCLK=166666667. Mar 5 11:47:43 dns-siika kernel: [42949373.190000] DNS323: Found ethernet MAC address: 00:21:91:57:50:28. Mar 5 11:47:43 dns-siika kernel: [42949373.230000] NET: Registered protocol family 2 Mar 5 11:47:43 dns-siika kernel: [42949373.240000] Switched to high resolution mode on CPU 0 Mar 5 11:47:43 dns-siika kernel: [42949373.320000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) Mar 5 11:47:43 dns-siika kernel: [42949373.320000] TCP established hash table entries: 2048 (order: 2, 16384 bytes) Mar 5 11:47:43 dns-siika kernel: [42949373.320000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) Mar 5 11:47:43 dns-siika kernel: [42949373.320000] TCP: Hash tables configured (established 2048 bind 2048) Mar 5 11:47:43 dns-siika kernel: [42949373.320000] TCP reno registered Mar 5 11:47:43 dns-siika kernel: [42949373.350000] NET: Registered protocol family 1 Mar 5 11:47:43 dns-siika kernel: [42949373.350000] checking if image is initramfs... it is Mar 5 11:47:43 dns-siika kernel: [42949374.880000] Freeing initrd memory: 2448K Mar 5 11:47:43 dns-siika kernel: [42949374.880000] NetWinder Floating Point Emulator V0.97 (double precision) Mar 5 11:47:43 dns-siika kernel: [42949374.880000] audit: initializing netlink socket (disabled) Mar 5 11:47:43 dns-siika kernel: [42949374.880000] type=2000 audit(1.920:1): initialized Mar 5 11:47:43 dns-siika kernel: [42949374.890000] VFS: Disk quotas dquot_6.5.1 Mar 5 11:47:43 dns-siika kernel: [42949374.890000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Mar 5 11:47:43 dns-siika kernel: [42949374.890000] msgmni has been set to 120 Mar 5 11:47:43 dns-siika kernel: [42949374.890000] async_tx: api initialized (async) Mar 5 11:47:43 dns-siika kernel: [42949374.890000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) Mar 5 11:47:43 dns-siika kernel: [42949374.890000] io scheduler noop registered Mar 5 11:47:43 dns-siika kernel: [42949374.890000] io scheduler anticipatory registered Mar 5 11:47:43 dns-siika kernel: [42949374.890000] io scheduler deadline registered Mar 5 11:47:43 dns-siika kernel: [42949374.890000] io scheduler cfq registered (default) Mar 5 11:47:43 dns-siika kernel: [42949374.910000] Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled Mar 5 11:47:43 dns-siika kernel: [42949374.910000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A Mar 5 11:47:43 dns-siika kernel: [42949374.910000] console [ttyS0] enabled Mar 5 11:47:43 dns-siika kernel: [42949375.210000] serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 4) is a 16550A Mar 5 11:47:43 dns-siika kernel: [42949375.240000] brd: module loaded Mar 5 11:47:43 dns-siika kernel: [42949375.240000] NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ Mar 5 11:47:43 dns-siika kernel: [42949375.250000] physmap platform flash device: 00800000 at f4000000 Mar 5 11:47:43 dns-siika kernel: [42949375.250000] physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank Mar 5 11:47:43 dns-siika kernel: [42949375.260000] Amd/Fujitsu Extended Query Table at 0x0040 Mar 5 11:47:43 dns-siika kernel: [42949375.270000] number of CFI chips: 1 Mar 5 11:47:43 dns-siika kernel: [42949375.270000] cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Mar 5 11:47:43 dns-siika kernel: [42949375.330000] RedBoot partition parsing not available Mar 5 11:47:43 dns-siika kernel: [42949375.330000] Using physmap partition information Mar 5 11:47:43 dns-siika kernel: [42949375.340000] Creating 5 MTD partitions on "physmap-flash.0": Mar 5 11:47:43 dns-siika kernel: [42949375.340000] 0x00000000-0x00010000 : "MTD1" Mar 5 11:47:43 dns-siika kernel: [42949375.350000] ftl_cs: FTL header not found. Mar 5 11:47:43 dns-siika kernel: [42949375.350000] 0x00010000-0x00020000 : "MTD2" Mar 5 11:47:43 dns-siika kernel: [42949375.360000] ftl_cs: FTL header not found. Mar 5 11:47:43 dns-siika kernel: [42949375.360000] 0x00020000-0x001a0000 : "Linux Kernel" Mar 5 11:47:43 dns-siika kernel: [42949375.370000] ftl_cs: FTL header not found. Mar 5 11:47:43 dns-siika kernel: [42949375.370000] 0x001a0000-0x007d0000 : "File System" Mar 5 11:47:43 dns-siika kernel: [42949375.380000] ftl_cs: FTL header not found. Mar 5 11:47:43 dns-siika kernel: [42949375.390000] 0x007d0000-0x00800000 : "u-boot" Mar 5 11:47:43 dns-siika kernel: [42949375.390000] ftl_cs: FTL header not found. Mar 5 11:47:43 dns-siika kernel: [42949375.400000] mice: PS/2 mouse device common for all mice Mar 5 11:47:43 dns-siika kernel: [42949375.410000] i2c /dev entries driver Mar 5 11:47:43 dns-siika kernel: [42949375.410000] rtc-m41t80 0-0068: chip found, driver version 0.05 Mar 5 11:47:43 dns-siika kernel: [42949375.420000] rtc-m41t80 0-0068: rtc core: registered m41t80 as rtc0 Mar 5 11:47:43 dns-siika kernel: [42949375.430000] Registered led device: power:blue Mar 5 11:47:43 dns-siika kernel: [42949375.430000] Registered led device: right:amber Mar 5 11:47:43 dns-siika kernel: [42949375.440000] Registered led device: left:amber Mar 5 11:47:43 dns-siika kernel: [42949375.450000] TCP cubic registered Mar 5 11:47:43 dns-siika kernel: [42949375.450000] NET: Registered protocol family 17 Mar 5 11:47:43 dns-siika kernel: [42949375.450000] VFP support v0.3: not present Mar 5 11:47:43 dns-siika kernel: [42949375.460000] registered taskstats version 1 Mar 5 11:47:43 dns-siika kernel: [42949375.470000] rtc-m41t80 0-0068: setting system clock to 2010-03-05 11:46:59 UTC (1267789619) Mar 5 11:47:43 dns-siika kernel: [42949375.470000] Freeing init memory: 116K Mar 5 11:47:43 dns-siika kernel: [42949375.970000] SCSI subsystem initialized Mar 5 11:47:43 dns-siika kernel: [42949376.050000] usbcore: registered new interface driver usbfs Mar 5 11:47:43 dns-siika kernel: [42949376.060000] usbcore: registered new interface driver hub Mar 5 11:47:43 dns-siika kernel: [42949376.070000] usbcore: registered new device driver usb Mar 5 11:47:43 dns-siika kernel: [42949376.100000] Initializing USB Mass Storage driver... Mar 5 11:47:43 dns-siika kernel: [42949376.100000] usbcore: registered new interface driver usb-storage Mar 5 11:47:43 dns-siika kernel: [42949376.110000] USB Mass Storage support registered. Mar 5 11:47:43 dns-siika kernel: [42949376.210000] orion-ehci orion-ehci.0: Marvell Orion EHCI Mar 5 11:47:43 dns-siika kernel: [42949376.220000] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 Mar 5 11:47:43 dns-siika kernel: [42949376.250000] orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000 Mar 5 11:47:43 dns-siika kernel: [42949376.270000] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 Mar 5 11:47:43 dns-siika kernel: [42949376.270000] usb usb1: configuration #1 chosen from 1 choice Mar 5 11:47:43 dns-siika kernel: [42949376.280000] hub 1-0:1.0: USB hub found Mar 5 11:47:43 dns-siika kernel: [42949376.280000] hub 1-0:1.0: 1 port detected Mar 5 11:47:43 dns-siika kernel: [42949376.400000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 Mar 5 11:47:43 dns-siika kernel: [42949376.400000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Mar 5 11:47:43 dns-siika kernel: [42949376.410000] usb usb1: Product: Marvell Orion EHCI Mar 5 11:47:43 dns-siika kernel: [42949376.420000] usb usb1: Manufacturer: Linux 2.6.26-2-orion5x ehci_hcd Mar 5 11:47:43 dns-siika kernel: [42949376.420000] usb usb1: SerialNumber: orion-ehci.0 Mar 5 11:47:43 dns-siika kernel: [42949376.430000] orion-ehci orion-ehci.1: Marvell Orion EHCI Mar 5 11:47:43 dns-siika kernel: [42949376.430000] orion-ehci orion-ehci.1: new USB bus registered, assigned bus number 2 Mar 5 11:47:43 dns-siika kernel: [42949376.470000] orion-ehci orion-ehci.1: irq 12, io mem 0xf10a0000 Mar 5 11:47:43 dns-siika kernel: [42949376.490000] orion-ehci orion-ehci.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 Mar 5 11:47:43 dns-siika kernel: [42949376.490000] usb usb2: configuration #1 chosen from 1 choice Mar 5 11:47:43 dns-siika kernel: [42949376.500000] hub 2-0:1.0: USB hub found Mar 5 11:47:43 dns-siika kernel: [42949376.500000] hub 2-0:1.0: 1 port detected Mar 5 11:47:43 dns-siika kernel: [42949376.620000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 Mar 5 11:47:43 dns-siika kernel: [42949376.620000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Mar 5 11:47:43 dns-siika kernel: [42949376.630000] usb usb2: Product: Marvell Orion EHCI Mar 5 11:47:43 dns-siika kernel: [42949376.640000] usb usb2: Manufacturer: Linux 2.6.26-2-orion5x ehci_hcd Mar 5 11:47:43 dns-siika kernel: [42949376.640000] usb usb2: SerialNumber: orion-ehci.1 Mar 5 11:47:43 dns-siika kernel: [42949376.680000] usb 1-1: new high speed USB device using orion-ehci and address 2 Mar 5 11:47:43 dns-siika kernel: [42949376.830000] usb 1-1: configuration #1 chosen from 1 choice Mar 5 11:47:43 dns-siika kernel: [42949376.840000] scsi0 : SCSI emulation for USB Mass Storage devices Mar 5 11:47:43 dns-siika kernel: [42949376.840000] usb-storage: device found at 2 Mar 5 11:47:43 dns-siika kernel: [42949376.840000] usb-storage: waiting for device to settle before scanning Mar 5 11:47:43 dns-siika kernel: [42949376.860000] usb 1-1: New USB device found, idVendor=152d, idProduct=2336 Mar 5 11:47:43 dns-siika kernel: [42949376.860000] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5 Mar 5 11:47:43 dns-siika kernel: [42949376.870000] usb 1-1: Product: JM20336 SATA, USB Combo Mar 5 11:47:43 dns-siika kernel: [42949376.870000] usb 1-1: Manufacturer: JMicron Mar 5 11:47:43 dns-siika kernel: [42949376.880000] usb 1-1: SerialNumber: 888888D88CA8 Mar 5 11:47:43 dns-siika kernel: [42949381.840000] usb-storage: device scan complete Mar 5 11:47:43 dns-siika kernel: [42949381.840000] scsi 0:0:0:0: Direct-Access WDC WD50 WD-WCAS8053 12.0 PQ: 0 ANSI: 2 CCS Mar 5 11:47:43 dns-siika kernel: [42949381.920000] Driver 'sd' needs updating - please use bus_type methods Mar 5 11:47:43 dns-siika kernel: [42949381.940000] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) Mar 5 11:47:43 dns-siika kernel: [42949381.950000] sd 0:0:0:0: [sda] Write Protect is off Mar 5 11:47:43 dns-siika kernel: [42949381.950000] sd 0:0:0:0: [sda] Mode Sense: 00 38 00 00 Mar 5 11:47:43 dns-siika kernel: [42949381.950000] sd 0:0:0:0: [sda] Assuming drive cache: write through Mar 5 11:47:43 dns-siika kernel: [42949381.960000] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB) Mar 5 11:47:43 dns-siika kernel: [42949381.970000] sd 0:0:0:0: [sda] Write Protect is off Mar 5 11:47:43 dns-siika kernel: [42949381.970000] sd 0:0:0:0: [sda] Mode Sense: 00 38 00 00 Mar 5 11:47:43 dns-siika kernel: [42949381.970000] sd 0:0:0:0: [sda] Assuming drive cache: write through Mar 5 11:47:43 dns-siika kernel: [42949381.980000] sda: sda1 sda2 sda3 sda4 < sda5 > Mar 5 11:47:43 dns-siika kernel: [42949382.020000] sd 0:0:0:0: [sda] Attached SCSI disk Mar 5 11:47:43 dns-siika kernel: [42949389.210000] md: raid1 personality registered for level 1 Mar 5 11:47:43 dns-siika kernel: [42949389.320000] md: md0 stopped. Mar 5 11:47:43 dns-siika kernel: [42949389.950000] EXT3-fs: INFO: recovery required on readonly filesystem. Mar 5 11:47:43 dns-siika kernel: [42949389.950000] EXT3-fs: write access will be enabled during recovery. Mar 5 11:47:43 dns-siika kernel: [42949390.080000] kjournald starting. Commit interval 5 seconds Mar 5 11:47:43 dns-siika kernel: [42949390.080000] EXT3-fs: recovery complete. Mar 5 11:47:43 dns-siika kernel: [42949390.090000] EXT3-fs: mounted filesystem with ordered data mode. Mar 5 11:47:43 dns-siika kernel: [42949393.050000] udevd version 125 started Mar 5 11:47:43 dns-siika kernel: [42949397.820000] MV-643xx 10/100/1000 Ethernet Driver Mar 5 11:47:43 dns-siika kernel: [42949397.830000] eth0: port 0 with MAC address 00:21:91:57:50:28 Mar 5 11:47:43 dns-siika kernel: [42949397.830000] eth0: Scatter Gather Enabled Mar 5 11:47:43 dns-siika kernel: [42949397.840000] eth0: TX TCP/IP Checksumming Supported Mar 5 11:47:43 dns-siika kernel: [42949397.840000] eth0: RX TCP/UDP Checksum Offload ON Mar 5 11:47:43 dns-siika kernel: [42949397.850000] eth0: RX NAPI Enabled Mar 5 11:47:43 dns-siika kernel: [42949398.220000] input: gpio-keys as /class/input/input0 Mar 5 11:47:43 dns-siika kernel: [42949398.610000] libata version 3.00 loaded. Mar 5 11:47:43 dns-siika kernel: [42949398.630000] sata_mv sata_mv.0: version 1.24 Mar 5 11:47:43 dns-siika kernel: [42949398.640000] sata_mv sata_mv.0: slots 32 ports 2 Mar 5 11:47:43 dns-siika kernel: [42949398.690000] scsi1 : sata_mv Mar 5 11:47:43 dns-siika kernel: [42949398.690000] scsi2 : sata_mv Mar 5 11:47:43 dns-siika kernel: [42949398.690000] ata1: SATA max UDMA/133 irq 29 Mar 5 11:47:43 dns-siika kernel: [42949398.700000] ata2: SATA max UDMA/133 irq 29 Mar 5 11:47:43 dns-siika kernel: [42949399.210000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Mar 5 11:47:43 dns-siika kernel: [42949399.260000] ata1.00: HPA detected: current 3907029168, native 18446744073321613488 Mar 5 11:47:43 dns-siika kernel: [42949399.260000] ata1.00: ATA-8: WDC WD20EADS-00S2B0, 01.00A01, max UDMA/133 Mar 5 11:47:43 dns-siika kernel: [42949399.270000] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) Mar 5 11:47:43 dns-siika kernel: [42949399.320000] ata1.00: configured for UDMA/133 Mar 5 11:47:43 dns-siika kernel: [42949399.830000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Mar 5 11:47:43 dns-siika kernel: [42949400.250000] ata2.00: HPA detected: current 3907029168, native 18446744073321613488 Mar 5 11:47:43 dns-siika kernel: [42949400.250000] ata2.00: ATA-8: WDC WD20EADS-00R6B0, 01.00A01, max UDMA/133 Mar 5 11:47:43 dns-siika kernel: [42949400.260000] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) Mar 5 11:47:43 dns-siika kernel: [42949400.330000] ata2.00: configured for UDMA/133 Mar 5 11:47:43 dns-siika kernel: [42949400.330000] scsi 1:0:0:0: Direct-Access ATA WDC WD20EADS-00S 01.0 PQ: 0 ANSI: 5 Mar 5 11:47:43 dns-siika kernel: [42949400.340000] sd 1:0:0:0: [sdb] 3907029168 512-byte hardware sectors (2000399 MB) Mar 5 11:47:43 dns-siika kernel: [42949400.350000] sd 1:0:0:0: [sdb] Write Protect is off Mar 5 11:47:43 dns-siika kernel: [42949400.350000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 Mar 5 11:47:43 dns-siika kernel: [42949400.350000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 5 11:47:43 dns-siika kernel: [42949400.360000] sd 1:0:0:0: [sdb] 3907029168 512-byte hardware sectors (2000399 MB) Mar 5 11:47:43 dns-siika kernel: [42949400.370000] sd 1:0:0:0: [sdb] Write Protect is off Mar 5 11:47:43 dns-siika kernel: [42949400.380000] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 Mar 5 11:47:43 dns-siika kernel: [42949400.380000] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 5 11:47:43 dns-siika kernel: [42949400.390000] sdb: sdb1 sdb2 sdb4 Mar 5 11:47:43 dns-siika kernel: [42949400.400000] sd 1:0:0:0: [sdb] Attached SCSI disk Mar 5 11:47:43 dns-siika kernel: [42949400.420000] scsi 2:0:0:0: Direct-Access ATA WDC WD20EADS-00R 01.0 PQ: 0 ANSI: 5 Mar 5 11:47:43 dns-siika kernel: [42949400.430000] sd 2:0:0:0: [sdc] 3907029168 512-byte hardware sectors (2000399 MB) Mar 5 11:47:43 dns-siika kernel: [42949400.430000] sd 2:0:0:0: [sdc] Write Protect is off Mar 5 11:47:43 dns-siika kernel: [42949400.440000] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 Mar 5 11:47:43 dns-siika kernel: [42949400.440000] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 5 11:47:43 dns-siika kernel: [42949400.450000] sd 2:0:0:0: [sdc] 3907029168 512-byte hardware sectors (2000399 MB) Mar 5 11:47:43 dns-siika kernel: [42949400.460000] sd 2:0:0:0: [sdc] Write Protect is off Mar 5 11:47:43 dns-siika kernel: [42949400.470000] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 Mar 5 11:47:43 dns-siika kernel: [42949400.470000] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 5 11:47:43 dns-siika kernel: [42949400.480000] sdc: sdc1 sdc2 sdc4 Mar 5 11:47:43 dns-siika kernel: [42949400.490000] sd 2:0:0:0: [sdc] Attached SCSI disk Mar 5 11:47:43 dns-siika kernel: [42949404.040000] Adding 176672k swap on /dev/sda5. Priority:-1 extents:1 across:176672k Mar 5 11:47:43 dns-siika kernel: [42949406.430000] EXT3 FS on sda3, internal journal Mar 5 11:47:43 dns-siika kernel: [42949408.760000] loop: module loaded Mar 5 11:47:43 dns-siika kernel: [42949409.360000] md: md0 stopped. Mar 5 11:47:43 dns-siika rsyslogd: [origin software="rsyslogd" swVersion="3.18.6" x-pid="1418" x-info="http://www.rsyslog.com"] restart Mar 5 11:47:44 dns-siika kernel: [42949419.970000] NET: Registered protocol family 10 Mar 5 11:47:44 dns-siika kernel: [42949419.980000] lo: Disabled Privacy Extensions Mar 5 11:47:46 dns-siika dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 Mar 5 11:47:46 dns-siika dhclient: DHCPOFFER from 192.168.0.1 Mar 5 11:47:46 dns-siika dhclient: DHCPREQUEST on eth0 to 255.255.255.255 port 67 Mar 5 11:47:46 dns-siika dhclient: DHCPACK from 192.168.0.1 Mar 5 11:47:46 dns-siika dhclient: bound to 192.168.0.186 -- renewal in 36568 seconds. Mar 5 11:47:49 dns-siika mdadm[1755]: DeviceDisappeared event detected on md device /dev/md0 Mar 5 11:47:49 dns-siika /usr/sbin/cron[1782]: (CRON) INFO (pidfile fd = 3) Mar 5 11:47:49 dns-siika /usr/sbin/cron[1783]: (CRON) STARTUP (fork ok) Mar 5 11:47:49 dns-siika /usr/sbin/cron[1783]: (CRON) INFO (Running @reboot jobs) Mar 5 12:12:43 dns-siika kernel: [42950919.310000] EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended Mar 5 12:17:01 dns-siika /USR/SBIN/CRON[1864]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly) Mar 5 12:41:15 dns-siika shutdown[1953]: shutting down for system reboot Mar 5 12:41:16 dns-siika init: Switching to runlevel: 6 Mar 5 12:41:17 dns-siika rpc.statd[1339]: Caught signal 15, un-registering and exiting.
syslog with kernel syslog-2.6.32-bpo.2-orion5x: (this is a backport for Lenny, but the kernel from Debian Squeeze worked similarly when I tested it)
Code:
Mar 5 11:41:47 dns-siika kernel: imklog 3.18.6, log source = /proc/kmsg started. Mar 5 11:41:47 dns-siika rsyslogd: [origin software="rsyslogd" swVersion="3.18.6" x-pid="1125" x-info="http://www.rsyslog.com"] restart Mar 5 11:41:47 dns-siika kernel: [ 0.000000] Initializing cgroup subsys cpuset Mar 5 11:41:47 dns-siika kernel: [ 0.000000] Initializing cgroup subsys cpu Mar 5 11:41:47 dns-siika kernel: [ 0.000000] Linux version 2.6.32-bpo.2-orion5x (Debian 2.6.32-8~bpo50+1) (norbert@tretkowski.de) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #1 Tue Feb 16 16:40:31 UTC 2010 Mar 5 11:41:47 dns-siika kernel: [ 0.000000] CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177 Mar 5 11:41:47 dns-siika kernel: [ 0.000000] CPU: VIVT data cache, VIVT instruction cache Mar 5 11:41:47 dns-siika kernel: [ 0.000000] Machine: D-Link DNS-323 Mar 5 11:41:47 dns-siika kernel: [ 0.000000] Memory policy: ECC disabled, Data cache writeback Mar 5 11:41:47 dns-siika kernel: [ 0.000000] On node 0 totalpages: 16384 Mar 5 11:41:47 dns-siika kernel: [ 0.000000] free_area_init_node: node 0, pgdat c0386a8c, node_mem_map c03ef000 Mar 5 11:41:47 dns-siika kernel: [ 0.000000] Normal zone: 128 pages used for memmap Mar 5 11:41:47 dns-siika kernel: [ 0.000000] Normal zone: 0 pages reserved Mar 5 11:41:47 dns-siika kernel: [ 0.000000] Normal zone: 16256 pages, LIFO batch:3 Mar 5 11:41:47 dns-siika kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Mar 5 11:41:47 dns-siika kernel: [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda3 rootdelay=10 ip=192.168.0.179::192.168.0.1:255.255.255.0:dns-siika:eth0:none Mar 5 11:41:47 dns-siika kernel: [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) Mar 5 11:41:47 dns-siika kernel: [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Mar 5 11:41:47 dns-siika kernel: [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Mar 5 11:41:47 dns-siika kernel: [ 0.000000] Memory: 64MB = 64MB total Mar 5 11:41:47 dns-siika kernel: [ 0.000000] Memory: 58396KB available (3196K code, 564K data, 120K init, 0K highmem) Mar 5 11:41:47 dns-siika kernel: [ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Mar 5 11:41:47 dns-siika kernel: [ 0.000000] Hierarchical RCU implementation. Mar 5 11:41:47 dns-siika kernel: [ 0.000000] NR_IRQS:64 Mar 5 11:41:47 dns-siika kernel: [ 0.000000] Console: colour dummy device 80x30 Mar 5 11:41:47 dns-siika kernel: [ 25.770047] Calibrating delay loop... 332.59 BogoMIPS (lpj=1662976) Mar 5 11:41:47 dns-siika kernel: [ 25.989975] Security Framework initialized Mar 5 11:41:47 dns-siika kernel: [ 25.990018] SELinux: Disabled at boot. Mar 5 11:41:47 dns-siika kernel: [ 25.990081] Mount-cache hash table entries: 512 Mar 5 11:41:47 dns-siika kernel: [ 25.990752] Initializing cgroup subsys ns Mar 5 11:41:47 dns-siika kernel: [ 25.990786] Initializing cgroup subsys cpuacct Mar 5 11:41:47 dns-siika kernel: [ 25.990811] Initializing cgroup subsys devices Mar 5 11:41:47 dns-siika kernel: [ 25.990835] Initializing cgroup subsys freezer Mar 5 11:41:47 dns-siika kernel: [ 25.990858] Initializing cgroup subsys net_cls Mar 5 11:41:47 dns-siika kernel: [ 25.990967] CPU: Testing write buffer coherency: ok Mar 5 11:41:47 dns-siika kernel: [ 25.992563] devtmpfs: initialized Mar 5 11:41:47 dns-siika kernel: [ 25.995657] regulator: core version 0.5 Mar 5 11:41:47 dns-siika kernel: [ 25.996100] NET: Registered protocol family 16 Mar 5 11:41:47 dns-siika kernel: [ 25.997228] Orion ID: MV88F5182-A2. TCLK=166666667. Mar 5 11:41:47 dns-siika kernel: [ 25.998043] DNS323: Found ethernet MAC address: 00:21:91:57:50:28. Mar 5 11:41:47 dns-siika kernel: [ 26.002931] bio: create slab <bio-0> at 0 Mar 5 11:41:47 dns-siika kernel: [ 26.003702] vgaarb: loaded Mar 5 11:41:47 dns-siika kernel: [ 26.005059] Switching to clocksource orion_clocksource Mar 5 11:41:47 dns-siika kernel: [ 26.015989] NET: Registered protocol family 2 Mar 5 11:41:47 dns-siika kernel: [ 26.016540] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) Mar 5 11:41:47 dns-siika kernel: [ 26.018364] TCP established hash table entries: 2048 (order: 2, 16384 bytes) Mar 5 11:41:47 dns-siika kernel: [ 26.018483] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) Mar 5 11:41:47 dns-siika kernel: [ 26.018550] TCP: Hash tables configured (established 2048 bind 2048) Mar 5 11:41:47 dns-siika kernel: [ 26.018576] TCP reno registered Mar 5 11:41:47 dns-siika kernel: [ 26.019013] NET: Registered protocol family 1 Mar 5 11:41:47 dns-siika kernel: [ 26.019488] Unpacking initramfs... Mar 5 11:41:47 dns-siika kernel: [ 26.668598] Freeing initrd memory: 2484K Mar 5 11:41:47 dns-siika kernel: [ 26.668774] NetWinder Floating Point Emulator V0.97 (double precision) Mar 5 11:41:47 dns-siika kernel: [ 26.669492] audit: initializing netlink socket (disabled) Mar 5 11:41:47 dns-siika kernel: [ 26.669577] type=2000 audit(0.890:1): initialized Mar 5 11:41:47 dns-siika kernel: [ 26.688038] VFS: Disk quotas dquot_6.5.2 Mar 5 11:41:47 dns-siika kernel: [ 26.688700] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Mar 5 11:41:47 dns-siika kernel: [ 26.689007] msgmni has been set to 119 Mar 5 11:41:47 dns-siika kernel: [ 26.690686] alg: No test for stdrng (krng) Mar 5 11:41:47 dns-siika kernel: [ 26.690993] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) Mar 5 11:41:47 dns-siika kernel: [ 26.691030] io scheduler noop registered Mar 5 11:41:47 dns-siika kernel: [ 26.691053] io scheduler anticipatory registered Mar 5 11:41:47 dns-siika kernel: [ 26.691077] io scheduler deadline registered Mar 5 11:41:47 dns-siika kernel: [ 26.691610] io scheduler cfq registered (default) Mar 5 11:41:47 dns-siika kernel: [ 26.708706] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled Mar 5 11:41:47 dns-siika kernel: [ 26.709857] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A Mar 5 11:41:47 dns-siika kernel: [ 27.021832] console [ttyS0] enabled Mar 5 11:41:47 dns-siika kernel: [ 27.026347] physmap platform flash device: 00800000 at f4000000 Mar 5 11:41:47 dns-siika kernel: [ 27.032536] physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank Mar 5 11:41:47 dns-siika kernel: [ 27.039093] Amd/Fujitsu Extended Query Table at 0x0040 Mar 5 11:41:47 dns-siika kernel: [ 27.044335] number of CFI chips: 1 Mar 5 11:41:47 dns-siika kernel: [ 27.047774] cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. Mar 5 11:41:47 dns-siika kernel: [ 27.095875] RedBoot partition parsing not available Mar 5 11:41:47 dns-siika kernel: [ 27.100752] Using physmap partition information Mar 5 11:41:47 dns-siika kernel: [ 27.105341] Creating 5 MTD partitions on "physmap-flash.0": Mar 5 11:41:47 dns-siika kernel: [ 27.110916] 0x000000000000-0x000000010000 : "MTD1" Mar 5 11:41:47 dns-siika kernel: [ 27.117154] 0x000000010000-0x000000020000 : "MTD2" Mar 5 11:41:47 dns-siika kernel: [ 27.123134] 0x000000020000-0x0000001a0000 : "Linux Kernel" Mar 5 11:41:47 dns-siika kernel: [ 27.129966] 0x0000001a0000-0x0000007d0000 : "File System" Mar 5 11:41:47 dns-siika kernel: [ 27.136732] 0x0000007d0000-0x000000800000 : "u-boot" Mar 5 11:41:47 dns-siika kernel: [ 27.143799] mice: PS/2 mouse device common for all mice Mar 5 11:41:47 dns-siika kernel: [ 27.150203] i2c /dev entries driver Mar 5 11:41:47 dns-siika kernel: [ 27.154640] rtc-m41t80 0-0068: chip found, driver version 0.05 Mar 5 11:41:47 dns-siika kernel: [ 27.160992] rtc-m41t80 0-0068: rtc core: registered m41t80 as rtc0 Mar 5 11:41:47 dns-siika kernel: [ 27.168730] Registered led device: power:blue Mar 5 11:41:47 dns-siika kernel: [ 27.173243] Registered led device: right:amber Mar 5 11:41:47 dns-siika kernel: [ 27.177918] Registered led device: left:amber Mar 5 11:41:47 dns-siika kernel: [ 27.185238] TCP cubic registered Mar 5 11:41:47 dns-siika kernel: [ 27.188471] NET: Registered protocol family 17 Mar 5 11:41:47 dns-siika kernel: [ 27.192945] VFP support v0.3: not present Mar 5 11:41:47 dns-siika kernel: [ 27.197866] registered taskstats version 1 Mar 5 11:41:47 dns-siika kernel: [ 27.203089] rtc-m41t80 0-0068: setting system clock to 2010-03-05 11:41:01 UTC (1267789261) Mar 5 11:41:47 dns-siika kernel: [ 27.211600] Freeing init memory: 120K Mar 5 11:41:47 dns-siika kernel: [ 27.845179] SCSI subsystem initialized Mar 5 11:41:47 dns-siika kernel: [ 28.028300] usbcore: registered new interface driver usbfs Mar 5 11:41:47 dns-siika kernel: [ 28.033985] usbcore: registered new interface driver hub Mar 5 11:41:47 dns-siika kernel: [ 28.039688] usbcore: registered new device driver usb Mar 5 11:41:47 dns-siika kernel: [ 28.109566] Initializing USB Mass Storage driver... Mar 5 11:41:47 dns-siika kernel: [ 28.114624] usbcore: registered new interface driver usb-storage Mar 5 11:41:47 dns-siika kernel: [ 28.120714] USB Mass Storage support registered. Mar 5 11:41:47 dns-siika kernel: [ 28.247091] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Mar 5 11:41:47 dns-siika kernel: [ 28.253731] orion-ehci orion-ehci.0: Marvell Orion EHCI Mar 5 11:41:47 dns-siika kernel: [ 28.259167] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 Mar 5 11:41:47 dns-siika kernel: [ 28.295215] orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000 Mar 5 11:41:47 dns-siika kernel: [ 28.315172] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 Mar 5 11:41:47 dns-siika kernel: [ 28.321229] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 Mar 5 11:41:47 dns-siika kernel: [ 28.328057] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Mar 5 11:41:47 dns-siika kernel: [ 28.335297] usb usb1: Product: Marvell Orion EHCI Mar 5 11:41:47 dns-siika kernel: [ 28.340000] usb usb1: Manufacturer: Linux 2.6.32-bpo.2-orion5x ehci_hcd Mar 5 11:41:47 dns-siika kernel: [ 28.346632] usb usb1: SerialNumber: orion-ehci.0 Mar 5 11:41:47 dns-siika kernel: [ 28.351973] usb usb1: configuration #1 chosen from 1 choice Mar 5 11:41:47 dns-siika kernel: [ 28.357907] hub 1-0:1.0: USB hub found Mar 5 11:41:47 dns-siika kernel: [ 28.361727] hub 1-0:1.0: 1 port detected Mar 5 11:41:47 dns-siika kernel: [ 28.685296] usb 1-1: new high speed USB device using orion-ehci and address 2 Mar 5 11:41:47 dns-siika kernel: [ 28.857772] usb 1-1: New USB device found, idVendor=152d, idProduct=2336 Mar 5 11:41:47 dns-siika kernel: [ 28.864477] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5 Mar 5 11:41:47 dns-siika kernel: [ 28.871679] usb 1-1: Product: JM20336 SATA, USB Combo Mar 5 11:41:47 dns-siika kernel: [ 28.876775] usb 1-1: Manufacturer: JMicron Mar 5 11:41:47 dns-siika kernel: [ 28.880871] usb 1-1: SerialNumber: 888888D88CA8 Mar 5 11:41:47 dns-siika kernel: [ 28.983745] usb 1-1: configuration #1 chosen from 1 choice Mar 5 11:41:47 dns-siika kernel: [ 29.065276] scsi0 : SCSI emulation for USB Mass Storage devices Mar 5 11:41:47 dns-siika kernel: [ 29.136042] usb-storage: device found at 2 Mar 5 11:41:47 dns-siika kernel: [ 29.136067] usb-storage: waiting for device to settle before scanning Mar 5 11:41:47 dns-siika kernel: [ 34.135662] usb-storage: device scan complete Mar 5 11:41:47 dns-siika kernel: [ 34.137036] scsi 0:0:0:0: Direct-Access WDC WD50 WD-WCAS8053 12.0 PQ: 0 ANSI: 2 CCS Mar 5 11:41:47 dns-siika kernel: [ 34.287218] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) Mar 5 11:41:47 dns-siika kernel: [ 34.299590] sd 0:0:0:0: [sda] Write Protect is off Mar 5 11:41:47 dns-siika kernel: [ 34.304387] sd 0:0:0:0: [sda] Mode Sense: 00 38 00 00 Mar 5 11:41:47 dns-siika kernel: [ 34.304411] sd 0:0:0:0: [sda] Assuming drive cache: write through Mar 5 11:41:47 dns-siika kernel: [ 34.312801] sd 0:0:0:0: [sda] Assuming drive cache: write through Mar 5 11:41:47 dns-siika kernel: [ 34.318996] sda: sda1 sda2 sda3 sda4 < sda5 > Mar 5 11:41:47 dns-siika kernel: [ 34.339085] sd 0:0:0:0: [sda] Assuming drive cache: write through Mar 5 11:41:47 dns-siika kernel: [ 34.345277] sd 0:0:0:0: [sda] Attached SCSI disk Mar 5 11:41:47 dns-siika kernel: [ 40.862649] md: raid1 personality registered for level 1 Mar 5 11:41:47 dns-siika kernel: [ 40.963087] md: md0 stopped. Mar 5 11:41:47 dns-siika kernel: [ 41.839496] kjournald starting. Commit interval 5 seconds Mar 5 11:41:47 dns-siika kernel: [ 41.845035] EXT3-fs: mounted filesystem with ordered data mode. Mar 5 11:41:47 dns-siika kernel: [ 45.106831] udevd version 125 started Mar 5 11:41:47 dns-siika kernel: [ 53.484444] lm75 0-0048: hwmon0: sensor 'lm75' Mar 5 11:41:47 dns-siika kernel: [ 53.706873] MV-643xx 10/100/1000 ethernet driver version 1.4 Mar 5 11:41:47 dns-siika kernel: [ 53.736715] mv643xx_eth smi: probed Mar 5 11:41:47 dns-siika kernel: [ 53.771898] net eth0: port 0 with MAC address 00:21:91:57:50:28 Mar 5 11:41:47 dns-siika kernel: [ 53.849584] input: gpio-keys as /devices/platform/gpio-keys/input/input0 Mar 5 11:41:47 dns-siika kernel: [ 54.809865] libata version 3.00 loaded. Mar 5 11:41:47 dns-siika kernel: [ 54.919351] sata_mv sata_mv.0: version 1.28 Mar 5 11:41:47 dns-siika kernel: [ 54.924561] sata_mv sata_mv.0: slots 32 ports 2 Mar 5 11:41:47 dns-siika kernel: [ 54.955326] scsi1 : sata_mv Mar 5 11:41:47 dns-siika kernel: [ 54.961258] scsi2 : sata_mv Mar 5 11:41:47 dns-siika kernel: [ 54.967224] ata1: SATA max UDMA/133 irq 29 Mar 5 11:41:47 dns-siika kernel: [ 54.971326] ata2: SATA max UDMA/133 irq 29 Mar 5 11:41:47 dns-siika kernel: [ 55.495206] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Mar 5 11:41:47 dns-siika kernel: [ 55.535227] ata1.00: ATA-8: WDC WD20EADS-00S2B0, 01.00A01, max UDMA/133 Mar 5 11:41:47 dns-siika kernel: [ 55.541836] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) Mar 5 11:41:47 dns-siika kernel: [ 55.585349] ata1.00: configured for UDMA/133 Mar 5 11:41:47 dns-siika kernel: [ 55.590308] scsi 1:0:0:0: Direct-Access ATA WDC WD20EADS-00S 01.0 PQ: 0 ANSI: 5 Mar 5 11:41:47 dns-siika kernel: [ 55.606786] sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) Mar 5 11:41:47 dns-siika kernel: [ 55.615391] sd 1:0:0:0: [sdb] Write Protect is off Mar 5 11:41:47 dns-siika kernel: [ 55.620192] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 Mar 5 11:41:47 dns-siika kernel: [ 55.620587] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 5 11:41:47 dns-siika kernel: [ 55.631630] sdb: sdb1 sdb2 sdb4 Mar 5 11:41:47 dns-siika kernel: [ 55.655829] sd 1:0:0:0: [sdb] Attached SCSI disk Mar 5 11:41:47 dns-siika kernel: [ 56.115199] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Mar 5 11:41:47 dns-siika kernel: [ 56.155241] ata2.00: ATA-8: WDC WD20EADS-00R6B0, 01.00A01, max UDMA/133 Mar 5 11:41:47 dns-siika kernel: [ 56.161850] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) Mar 5 11:41:47 dns-siika kernel: [ 56.205364] ata2.00: configured for UDMA/133 Mar 5 11:41:47 dns-siika kernel: [ 56.210338] scsi 2:0:0:0: Direct-Access ATA WDC WD20EADS-00R 01.0 PQ: 0 ANSI: 5 Mar 5 11:41:47 dns-siika kernel: [ 56.223203] sd 2:0:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) Mar 5 11:41:47 dns-siika kernel: [ 56.235178] sd 2:0:0:0: [sdc] Write Protect is off Mar 5 11:41:47 dns-siika kernel: [ 56.239982] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 Mar 5 11:41:47 dns-siika kernel: [ 56.240385] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 5 11:41:47 dns-siika kernel: [ 56.251276] sdc: sdc1 sdc2 sdc4 Mar 5 11:41:47 dns-siika kernel: [ 56.280160] sd 2:0:0:0: [sdc] Attached SCSI disk Mar 5 11:41:47 dns-siika kernel: [ 61.328921] Adding 176672k swap on /dev/sda5. Priority:-1 extents:1 across:176672k Mar 5 11:41:47 dns-siika kernel: [ 63.749199] EXT3 FS on sda3, internal journal Mar 5 11:41:47 dns-siika kernel: [ 66.183208] loop: module loaded Mar 5 11:41:47 dns-siika kernel: [ 66.861653] md: md0 stopped. Mar 5 11:41:48 dns-siika dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3 Mar 5 11:41:48 dns-siika kernel: [ 73.933803] eth0: link up, 1000 Mb/s, full duplex, flow control disabled Mar 5 11:41:48 dns-siika kernel: [ 74.555412] NET: Registered protocol family 10 Mar 5 11:41:48 dns-siika kernel: [ 74.564482] lo: Disabled Privacy Extensions Mar 5 11:41:51 dns-siika dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7 Mar 5 11:41:52 dns-siika mdadm[1433]: DeviceDisappeared event detected on md device /dev/md0 Mar 5 11:41:53 dns-siika /usr/sbin/cron[1460]: (CRON) INFO (pidfile fd = 3) Mar 5 11:41:53 dns-siika /usr/sbin/cron[1461]: (CRON) STARTUP (fork ok) Mar 5 11:41:53 dns-siika /usr/sbin/cron[1461]: (CRON) INFO (Running @reboot jobs) Mar 5 11:41:58 dns-siika dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 14 Mar 5 11:41:59 dns-siika kernel: [ 85.295157] eth0: no IPv6 routers present Mar 5 11:42:12 dns-siika dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 19 Mar 5 11:42:31 dns-siika dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 18 Mar 5 11:42:49 dns-siika dhclient: No DHCPOFFERS received. Mar 5 11:42:49 dns-siika dhclient: No working leases in persistent database - sleeping. Mar 5 11:42:58 dns-siika kernel: [ 144.268985] eth0: link down Mar 5 11:43:02 dns-siika kernel: [ 148.204429] eth0: link up, 1000 Mb/s, full duplex, flow control disabled
Instructions for installing and booting Debian natively on DNS-323 NAS:
These instructions assume that you have a working linux installation on your NAS, in my case it was just fonz' funplug 0.5.
1. Download debian-installer (netboot.img)
2. Download ffp-reloaded
3. Download dns323-firmware-tools
3. Install ffp-reloaded.
4. Install dns-323-firmware-tools
5. Strip the initial ramdisk and kernel from netboot.img. You can use splitdns323fw from dns323-firmware-tools to separate uBoot kernel and ramdisk images from the firmware image. Then you need to remove the 64bit uBoot header from both files. (dd if=x of=y bs=64 skip=1)
6. Boot the Debian installer with ffp-reloaded using the kernel and initial ramdisk from netboot.img
7. Install Debian. I did this in expert mode so I could control the installation process more accurately. I don't know if this is really necessary since I have never tested the standard installation. Does the standard installation give you the choice of whether or not to install the bootloader to firmware? Anyway, Lenny installs with kernel 2.6.26 and Squeeze with 2.6.32. I did not test unstable yet.
8. Boot Debian with ffp-reloaded using the kernel and initial ramdisk from the newly installed Debian installation. You can use vmlinuz and initrd.gz from Debian's /boot without any modifications. I installed to USB hard disk that was assigned to /dev/sdc during installation, but still I had to boot to /dev/sda to make things work. (./reload.sh -k vmlinuz -i initrd.gz root=/dev/sda)
Additional notes: Debian-installer let's you decide how to partition your drives, so your data in the internal disks of the NAS should not be in danger if you use external disk like I did.
Last edited by juhog (2010-03-05 21:20:08)
Offline
#2 2010-03-05 21:21:06
- juhog
- Member
- Registered: 2010-03-05
- Posts: 9
Re: Native Debian without flashing the firmware - instructions and issues
So, I spent some time tinkering with my DNS-323 and ended up making some kind of bootloader for it. My idea was to use the initial ramdisks that Debian's standard tools create, and make them work as they should have worked for starters for this device. I added the possibilities to telnet into the device during the booting process (netcat and busybox' telnetd), do filesystem operations (e2fsprogs) and as most important of them all, the possibility to load another kernel and ramdisk from disk and boot it (kexec).
In my opinion something like this should be installed by default by the Debian Installer.
The script for creating the bootloader is attached below, studying it is necessary for being able to use it and the bootloader, I have made no other documentation for them (yet). All the functions can be enabled and disabled through kernel commandline parameters (/proc/cmdline). You will need to apply minor patch to kexec-tools source code before the compiled result will work as intented on the device. The diff for that is also supplied below.
Script for editing initrd.img made by Debian's update-initramfs:
Code:
#!/bin/sh
#DNS323 Custom Kernel Bootloader setup script.
#Copyright (C) 2010 Juho Grundström - juho@krunde.net
#
#This program is free software; you can redistribute it and/or modify it
#under the terms of the GNU General Public License as published by the
#Free Software Foundation; either version 2 of the License, or (at your
#option) any later version.
#
#This program is distributed in the hope that it will be useful,
#but WITHOUT ANY WARRANTY; without even the implied warranty of
#MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
#See the GNU General Public License for more details.
#
#You should have received a copy of the GNU General Public License
#along with this program; if not, write to the Free Software
#Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
. /usr/share/initramfs-tools/hook-functions
dnsloaderversion="2.6.26-juhog-14.03.2010"
tempdir=/tmp
DESTDIR=${tempdir}/dnsloader/initramfs/usr
if [ -d "${tempdir}/dnsloader/initramfs" ]; then
echo "Temporary directory ${tempdir}/dnsloader/initramfs exists."
echo "You need to remove it before running the script, or change the script to use another directory."
exit 0
fi
[ -d "${tempdir}" ] || mkdir ${tempdir}
[ -d "${tempdir}/dnsloader" ] || mkdir ${tempdir}/dnsloader
[ -d "${tempdir}/dnsloader/tmp" ] || mkdir ${tempdir}/dnsloader/tmp
cp -p /etc/passwd ${tempdir}/dnsloader/tmp/
cp -p /etc/group ${tempdir}/dnsloader/tmp/
cp -p /etc/shadow ${tempdir}/dnsloader/tmp/
if [ -e "${tempdir}/dnsloader/passwd" ]; then
cp -p ${tempdir}/dnsloader/passwd ${tempdir}/dnsloader/tmp/
fi
if [ -e "${tempdir}/dnsloader/group" ]; then
cp -p ${tempdir}/dnsloader/group ${tempdir}/dnsloader/tmp/
fi
if [ -e "${tempdir}/dnsloader/shadow" ]; then
cp -p ${tempdir}/dnsloader/shadow ${tempdir}/dnsloader/tmp/
fi
grep bash ${tempdir}/dnsloader/tmp/passwd
if [ $? -eq 0 ]; then
echo "Reference to bash detected in ${tempdir}/dnsloader/tmp/passwd."
echo "Please fix the passwd to use ash/sh shell and place the corrected version to ${tempdir}/dnsloader/."
exit 0
fi
[ -d "${tempdir}/dnsloader/initramfs" ] || mkdir ${tempdir}/dnsloader/initramfs
cd ${tempdir}/dnsloader/initramfs
[ -d usr ] || mkdir usr
[ -d usr/sbin ] || mkdir usr/sbin
[ -d usr/bin ] || mkdir usr/bin
[ -d usr/lib ] || mkdir usr/lib
# Make sure you have cpio installed.
zcat /boot/initrd.img-${dnsloaderversion} | (while true; do cpio -i -d -H newc --no-absolute-filenames || exit; done)
cp -p ../tmp/passwd etc/
cp -p ../tmp/group etc/
cp -p ../tmp/shadow etc/
# Make sure you have at least kexec installed.
# Make sure your busybox has telnetd applet built in it.
ln -s /bin/busybox sbin/telnetd
cd ${tempdir}/dnsloader/initramfs/usr
copy_exec /sbin/blkid
copy_exec /sbin/e2fsck
copy_exec /sbin/tune2fs
copy_exec /sbin/resize2fs
copy_exec /sbin/mke2fs
copy_exec /sbin/dumpe2fs
copy_exec /sbin/debugfs
copy_exec /sbin/fsck
copy_exec /sbin/fsck.ext2
copy_exec /sbin/fsck.ext3
copy_exec /sbin/fsck.ext4
copy_exec /sbin/mkfs
copy_exec /sbin/mkfs.ext2
copy_exec /sbin/mkfs.ext3
copy_exec /sbin/mkfs.ext4
copy_exec /sbin/kexec
copy_exec /bin/nc.traditional /bin/nc
cp -rpL * ../
cd ..
_out_filename=init
if [ ! -e ${_out_finename}_original ] ; then
cp $_out_filename ${_out_filename}_original
fi
cp /dev/null $_out_filename
while read line ; do
set -- $line
if [ "$1 $2" = "maybe_break mount" ] ; then
echo '
export KERNELNAME=vmlinuz
export INITRDNAME=initrd.img
export BOOTPART=
export BOOTPARTDELAY=
export BOOTPARTFLAGS="-o ro"
export BOOTPARTFSTYPE=ext2
export DEBUGIP=
export DEBUGPORT=
export bootpartmnt=/boot
export DISABLETELNET=
for x in $(cat /proc/cmdline); do
case $x in
kernelname=*)
KERNELNAME="${x#kernelname=}"
;;
initrdname=*)
INITRDNAME="${x#initrdname=}"
;;
bootpart=*)
BOOTPART="${x#bootpart=}"
case $BOOTPART in
LABEL=*)
BOOTPART="/dev/disk/by-label/${BOOTPART#LABEL=}"
;;
UUID=*)
BOOTPART="/dev/disk/by-uuid/${BOOTPART#UUID=}"
;;
esac
;;
bootpartflags=*)
BOOTPARTFLAGS="-o ${x#bootpartflags=}"
;;
bootpartfstype=*)
BOOTPARTFSTYPE="${x#bootpartfstype=}"
;;
bootpartdelay=*)
BOOTPARTDELAY="${x#bootpartdelay=}"
case ${BOOTPARTDELAY} in
*[![:digit:].]*)
BOOTPARTDELAY=
;;
esac
;;
debugip=*)
DEBUGIP="${x#debugip=}"
;;
debugport=*)
DEBUGPORT="${x#debugport=}"
;;
disabletelnet)
DISABLETELNET=y
;;
esac
done
if [ ! -z "${BOOTPARTDELAY}" ]; then
sleep ${BOOTPARTDELAY} 2>&1 >/dev/null | nc ${DEBUGIP} ${DEBUGPORT} -w 1
fi
if [ ! -z "${BOOTPART}" ]; then
echo "Mounting ${BOOTPART}" | nc ${DEBUGIP} ${DEBUGPORT} -w 1
[ -d "${bootpartmnt}" ] || mkdir -m 0700 ${bootpartmnt} 2>&1 >/dev/null | nc ${DEBUGIP} ${DEBUGPORT} -w 1
mount -t ${BOOTPARTFSTYPE} ${BOOTPARTFLAGS} ${BOOTPART} ${bootpartmnt} 2>&1 >/dev/null | nc ${DEBUGIP} ${DEBUGPORT} -w 1
fi
busybox --install -s 2>&1 >/dev/null | nc ${DEBUGIP} ${DEBUGPORT} -w 1
wait
if [ -z "${DISABLETELNET}" ]; then
echo "Booting paused, connecting to telnetd possible in 3 seconds -- nc -l -p 23 -w 5 -e /sbin/telnetd" | nc ${DEBUGIP} ${DEBUGPORT} -w 1
mkdir /dev/pts 2>&1 >/dev/null | nc ${DEBUGIP} ${DEBUGPORT} -w 1
mount -t devpts devpts /dev/pts 2>&1 >/dev/null | nc ${DEBUGIP} ${DEBUGPORT} -w 1
wait
/bin/nc -l -p 23 -w 5 -e /sbin/telnetd 2>&1 >/dev/null | nc ${DEBUGIP} ${DEBUGPORT} -w 1
umount /dev/pts 2>&1 >/dev/null | nc ${DEBUGIP} ${DEBUGPORT} -w 1
echo "Booting continues" | nc ${DEBUGIP} ${DEBUGPORT} -w 1
fi
if [ -e "${bootpartmnt}/${KERNELNAME}" ]; then
echo "Loading linux kernel from disk..." | nc ${DEBUGIP} ${DEBUGPORT} -w 1
if [ -x /sbin/kexec ]; then
kexec -l --append="`cat /proc/cmdline`" --initrd=${bootpartmnt}/${INITRDNAME} ${bootpartmnt}/${KERNELNAME} 2>&1 >/dev/null | nc ${DEBUGIP} ${DEBUGPORT} -w 1
sync 2>&1 >/dev/null | nc ${DEBUGIP} ${DEBUGPORT} -w 1
umount -a 2>&1 >/dev/null | nc ${DEBUGIP} ${DEBUGPORT} -w 1
exec kexec -e 2>&1 >/dev/null | nc ${DEBUGIP} ${DEBUGPORT} -w 1
fi
echo "Loading kernel failed. Using the current kernel instead" | nc ${DEBUGIP} ${DEBUGPORT} -w 1
fi
if [ ! -z "${BOOTPART}" ]; then
echo "Unmounting ${BOOTPART}" | nc ${DEBUGIP} ${DEBUGPORT} -w 1
umount ${bootpartmnt} 2>&1 >/dev/null | nc ${DEBUGIP} ${DEBUGPORT} -w 1
fi
unset KERNELNAME
unset INITRDNAME
unset BOOTPART
unset BOOTPARTDELAY
unset BOOTPARTFLAGS
unset BOOTPARTFSTYPE
unset bootpartmnt
unset DEBUGIP
unset DEBUGPORT
unset DISABLETELNET
' >> $_out_filename
echo $line >> $_out_filename
else
echo $line >> $_out_filename
fi
done < ${_out_filename}_original
rm init_original
find . -print0 | cpio -ov -0 --format=newc | gzip -9 > /boot/initrd.img-bootloader
cd /boot/
ln -s vmlinuz-${dnsloaderversion} vmlinuz-bootloaderKernel (Debian 2.6.26) .config for use with above initial ramdisk is uploaded as attachment to this post. Of course you can use other kernels as well, but the one build with that config is confirmed to work on my system (hardware revision B1), so it could work for others too.
Code:
--- kexec-tools-2.0.1.orig/kexec/arch/arm/kexec-arm.c
+++ kexec-tools-2.0.1/kexec/arch/arm/kexec-arm.c
@@ -110,6 +110,7 @@
const struct arch_map_entry arches[] = {
{ "arm", KEXEC_ARCH_ARM },
+ { "armv5tel", KEXEC_ARCH_ARM },
{ 0 },
};Files related to this project can be found from http://krunde.net/~juho/
For more Debian info, go to http://www.cyrius.com/debian/
Last edited by juhog (2010-03-29 00:09:44)
Offline
#3 2010-03-06 12:19:10
- mushanga
- Member
- Registered: 2009-06-26
- Posts: 46
Re: Native Debian without flashing the firmware - instructions and issues
Hi Juhog,
first, congrats because you've achieved what I'm loosely trying to do for months (ok, I'm trying not so hard but still). Thanks for the confirmation, I was about to try just that (launch the Debian installer through ffp-reload).
I've tried the same approach with a gentoo kernel with a similar result: my 2.6.32.7 kernel only links to 1000M (directly connected to my macbook, configured to auto-negotiate).
If connected to my 100M switch (both autoneg) it never links up.
If linked to 1000M (still macbook) and forced to 100M (#mii-tool -F 100baseTx-FD eth0) I loose the link.
If linked to 1000M (still macbook) and renegotiated to 100M (#mii-tool -A 100baseTx-FD,100baseTx-HD eth0) it links to 1000M!!!
I think about a kind of bug in the MV-643xx driver. Sadly I don't know who to tell...
Look: in your 2.6.26 kernel the driver announces itself as "[42949397.820000] MV-643xx 10/100/1000 Ethernet Driver"
In your 2.6.32 it is "[ 53.706873] MV-643xx 10/100/1000 ethernet driver version 1.4", same as mine BTW.
So the 2 are different versions.
Another difference is the gcc versions (4.1.3 against 4.3.2 and even 4.3.4 for me).
I do not see any other reason...
If you suspect a difference in the kernel config just look at them!
Usually they are provided with the kernel .deb and copied in /boot; just diff them
BTW, what is your HW revision? Mine is C1 with u-boot 1.7.6_NAS (Marvell Development Board (LSP Version 1.7.6_NAS)-- RD-88F5182-NAS-2)
Here is my dmesg when trying to renegotiate the link (#mii-tool -A 100baseTx-FD,100baseTx-HD eth0):
Code:
[ 0.000000] Linux version 2.6.32.7 (root@mercenaire) (gcc version 4.3.4 (Gentoo 4.3.4 p1.0, pie-10.1.5) ) #1 Wed Feb 3 17:16:36 CET 2010 [ 0.000000] CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: D-Link DNS-323 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat c02fbeb0, node_mem_map c030f000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16256 pages, LIFO batch:3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: logfile=/mnt/HD_a2/tools.log netconsole=@192.168.33.3/,6666@192.168.33.1/ ip=192.168.33.3::192.168.33.254:255.255.255.0:Tiromancino:eth0:none [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 64MB = 64MB total [ 0.000000] Memory: 59212KB available (2692K code, 197K data, 112K init, 0K highmem) [ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:64 [ 25.769863] Calibrating delay loop... 332.59 BogoMIPS (lpj=1662976) [ 25.989975] Mount-cache hash table entries: 512 [ 25.990496] CPU: Testing write buffer coherency: ok [ 25.993198] NET: Registered protocol family 16 [ 25.993856] Orion ID: MV88F5182-A2. TCLK=166666667. [ 25.994527] DNS323: Found ethernet MAC address: 00:22:b0:dd:54:68. [ 25.999500] bio: create slab <bio-0> at 0 [ 26.000518] SCSI subsystem initialized [ 26.000814] libata version 3.00 loaded. [ 26.001245] usbcore: registered new interface driver usbfs [ 26.001424] usbcore: registered new interface driver hub [ 26.001687] usbcore: registered new device driver usb [ 26.002484] Switching to clocksource orion_clocksource [ 26.003584] NET: Registered protocol family 2 [ 26.003754] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 26.004089] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 26.004207] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 26.004273] TCP: Hash tables configured (established 2048 bind 2048) [ 26.004297] TCP reno registered [ 26.004466] NET: Registered protocol family 1 [ 26.004843] Unpacking initramfs... [ 26.482840] Freeing initrd memory: 2568K [ 26.482984] NetWinder Floating Point Emulator V0.97 (extended precision) [ 26.497735] msgmni has been set to 120 [ 26.498832] alg: No test for stdrng (krng) [ 26.499439] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 26.499474] io scheduler noop registered [ 26.499950] io scheduler cfq registered (default) [ 26.504600] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 26.505280] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A [ 29.512769] console [ttyS0] enabled [ 29.556097] MV-643xx 10/100/1000 ethernet driver version 1.4 [ 29.624132] mv643xx_eth smi: probed [ 29.669167] net eth0: port 0 with MAC address 00:22:b0:dd:54:68 [ 29.740200] netconsole: local port 6665 [ 29.786137] netconsole: local IP 192.168.33.3 [ 29.838312] netconsole: interface eth0 [ 29.883205] netconsole: remote port 6666 [ 29.930182] netconsole: remote IP 192.168.33.1 [ 29.983408] netconsole: remote ethernet address ff:ff:ff:ff:ff:ff [ 30.056432] netconsole: device eth0 not up yet, forcing it [ 31.761413] eth0: link up, 1000 Mb/s, full duplex, flow control enabled [ 35.536396] console [netcon0] enabled [ 35.580274] netconsole: network logging started [ 35.634538] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 35.712838] orion-ehci orion-ehci.0: Marvell Orion EHCI [ 35.775575] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 35.892610] orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000 [ 35.982576] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 36.054115] usb usb1: configuration #1 chosen from 1 choice [ 36.121240] hub 1-0:1.0: USB hub found [ 36.166245] hub 1-0:1.0: 1 port detected [ 36.213840] Initializing USB Mass Storage driver... [ 36.272513] usbcore: registered new interface driver usb-storage [ 36.344524] USB Mass Storage support registered. [ 36.400128] i2c /dev entries driver [ 36.442741] rtc-m41t80 0-0068: chip found, driver version 0.05 [ 36.512981] rtc-m41t80 0-0068: rtc core: registered m41t80 as rtc0 [ 36.589120] lm75 0-0048: hwmon1: sensor 'lm75' [ 36.643565] Registered led device: power:blue [ 36.695967] Registered led device: right:amber [ 36.749393] Registered led device: left:amber [ 36.803790] usbcore: registered new interface driver usbhid [ 36.870639] usbhid: v2.6:USB HID core driver [ 36.921863] nf_conntrack version 0.5.0 (966 buckets, 3864 max) [ 36.992973] ip_tables: (C) 2000-2006 Netfilter Core Team [ 37.056803] TCP cubic registered [ 37.097212] NET: Registered protocol family 10 [ 37.151976] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 37.217040] NET: Registered protocol family 17 [ 37.271950] rtc-m41t80 0-0068: setting system clock to 2010-03-02 18:50:13 UTC (1267555813) [ 37.372302] Freeing init memory: 112K [ 47.212556] eth0: no IPv6 routers present [ 47.750443] sata_mv sata_mv.0: version 1.28 [ 47.751469] sata_mv sata_mv.0: slots 32 ports 2 [ 47.754918] scsi0 : sata_mv [ 47.760707] scsi1 : sata_mv [ 47.764416] ata1: SATA max UDMA/133 irq 29 [ 47.764447] ata2: SATA max UDMA/133 irq 29 [ 48.272605] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 48.292765] ata1.00: ATA-8: WDC WD10EADS-65L5B1, 01.01A01, max UDMA/133 [ 48.292801] ata1.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 48.332866] ata1.00: configured for UDMA/133 [ 48.333528] scsi 0:0:0:0: Direct-Access ATA WDC WD10EADS-65L 01.0 PQ: 0 ANSI: 5 [ 48.343217] sd 0:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) [ 48.343903] sd 0:0:0:0: [sda] Write Protect is off [ 48.343938] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 48.344294] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 48.345300] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 48.346941] sda: sda1 sda2 sda4 [ 48.380970] sd 0:0:0:0: [sda] Attached SCSI disk [ 48.852601] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 48.872886] ata2.00: ATA-7: SAMSUNG HD103UJ, 1AA01113, max UDMA7 [ 48.872921] ata2.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 48.892995] ata2.00: configured for UDMA/133 [ 48.893627] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD103UJ 1AA0 PQ: 0 ANSI: 5 [ 48.900350] sd 1:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) [ 48.901025] sd 1:0:0:0: [sdb] Write Protect is off [ 48.901061] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 48.901413] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 48.902969] sdb: [ 48.908133] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 48.909676] sdb1 sdb2 sdb4 [ 48.927598] sd 1:0:0:0: [sdb] Attached SCSI disk [ 50.363306] kjournald starting. Commit interval 5 seconds [ 50.367565] EXT3 FS on sda2, internal journal [ 50.367603] EXT3-fs: mounted filesystem with writeback data mode. [ 56.476813] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 58.129512] eth0: link up, 1000 Mb/s, full duplex, flow control enabled [ 58.208959] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 68.412550] eth0: no IPv6 routers present [ 329.620517] eth0: link down [ 349.197778] eth0: link up, 1000 Mb/s, full duplex, flow control disabled
I will continue to investigate and keep you informed.
Last edited by mushanga (2010-03-06 12:43:02)
Offline
#4 2010-03-07 02:19:35
- juhog
- Member
- Registered: 2010-03-05
- Posts: 9
Re: Native Debian without flashing the firmware - instructions and issues
mushanga wrote:
...
BTW, what is your HW revision? Mine is C1 with u-boot 1.7.6_NAS (Marvell Development Board (LSP Version 1.7.6_NAS)-- RD-88F5182-NAS-2)
...
B1, I think. Anyway, I'm far away from home so sadly I can't research this issue further just yet. 
Good job finding about the possible issue with the different ethernet driver versions!
Offline
#5 2010-03-07 17:43:45
- bernd123
- Member
- Registered: 2010-03-07
- Posts: 12
Re: Native Debian without flashing the firmware - instructions and issues
Hi mushanga,
mushanga wrote:
BTW, what is your HW revision? Mine is C1 with u-boot 1.7.6_NAS (Marvell Development Board (LSP Version 1.7.6_NAS)-- RD-88F5182-NAS-2)
how did you accomplish that?
I have also a C1 (MARVELL BOARD: RD-88F5182-NAS-2 LE, U-Boot 1.1.1 (Feb 26 2009 - 11:33:03) Marvell version: 1.7.3.003), but I'm failing to get any kernel booted (except D-links).
I tried the kernel/initrd from the Debian-Installer (also nightly builds) but the device always just switches off, even before mounting the initrd. This was be done by loading kernel/initrd over u-boots console into memory and booting off memory without flashing. This procedure works with D-Links kernel/initrd.
Why do our U-Boot versions differ? Are you sure about your version?
Any hint would be greatly appreciated1
Regards
Offline
#6 2010-03-07 21:09:15
- mushanga
- Member
- Registered: 2009-06-26
- Posts: 46
Re: Native Debian without flashing the firmware - instructions and issues
I cannot access the console since I have no JTAG or Serial adaptor, it's only a deduction from the DLINK 1.08b01 firmware dmesg output:
Code:
Linux version 2.6.12.6-arm1 (tim@SWTEST2) (gcc version 3.3.3) #31 Mon Mar 23 19:39:43 CST 2009 CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ) CPU0: D VIVT write-back cache CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets Machine: MV-88fxx81 Using UBoot passing parameters structure Sys Clk = 166000000, Tclk = 166000000 Memory policy: ECC disabled, Data cache writeback On node 0 totalpages: 16384 DMA zone: 16384 pages, LIFO batch:7 Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 Built 1 zonelists Kernel command line: root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none PID hash table entries: 512 (order: 9, 8192 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 64MB 0MB 0MB 0MB = 64MB total Memory: 55324KB available (2520K code, 455K data, 112K init) Calibrating delay loop... 331.77 BogoMIPS (lpj=1658880) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 6310K NET: Registered protocol family 16 Marvell Development Board (LSP Version 1.7.6_NAS)-- RD-88F5182-NAS-2 Detected Tclk 166000000 and SysClk 166000000 Marvell USB EHCI Host controller #0: c03b9bc0 Marvell USB EHCI Host controller #1: c03b9a40 pexBarOverlapDetect: winNum 2 overlap current 0 mvPexInit:Warning :Bar 2 size is illigal it will be disabled please check Pex and CPU windows configuration PCI: bus0: Fast back to back transfers enabled PCI: bus1: Fast back to back transfers enabled SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub cesadev_init(c0012498) Fast Floating Point Emulator V0.9 (c) Peter Teichmann. inotify device minor=63 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) squashfs: version 3.3 (2007/10/31) Phillip Lougher Initializing Cryptographic API Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled ttyS0 at MMIO 0x0 (irq = 3) is a 16550A io scheduler noop registered io scheduler deadline registered RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize loop: loaded (max 8 devices) Marvell Gigabit Ethernet Driver 'egiga': o Ethernet descriptors in DRAM o DRAM SW cache-coherency o Checksum offload enabled o Loading network interface 'egiga0' Intergrated Sata device found scsi0 : Marvell SCSI to SATA adapter scsi1 : Marvell SCSI to SATA adapter Vendor: WDC Model: WD10EADS-65L5B1 Rev: 01.0 Type: Direct-Access ANSI SCSI revision: 03 Vendor: SAMSUNG Model: HD103UJ Rev: 1AA0 Type: Direct-Access ANSI SCSI revision: 03 Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0 Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0 physmap flash device: 800000 at ff800000 phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. cmdlinepart partition parsing not available RedBoot partition parsing not available Using physmap partition definition Creating 5 MTD partitions on "phys_mapped_flash": 0x00000000-0x00010000 : "MTD1" 0x00010000-0x00020000 : "MTD2" 0x00020000-0x001a0000 : "Linux Kernel" 0x001a0000-0x007d0000 : "File System" 0x007d0000-0x00800000 : "u-boot" ehci_platform ehci_platform.20865: EHCI Host Controller ehci_platform ehci_platform.20865: new USB bus registered, assigned bus number 1 ehci_platform ehci_platform.20865: irq 17, io mem 0x00000000 ehci_platform ehci_platform.20865: park 0 ehci_platform ehci_platform.20865: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ehci_platform ehci_platform.86401: EHCI Host Controller ehci_platform ehci_platform.86401: new USB bus registered, assigned bus number 2 ehci_platform ehci_platform.86401: irq 12, io mem 0x00000000 ehci_platform ehci_platform.86401: park 0 ehci_platform ehci_platform.86401: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) mice: PS/2 mouse device common for all mice md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 4Kbytes TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) NET: Registered protocol family 1 NET: Registered protocol family 17 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. RAMDISK: Compressed image found at block 0 EXT2-fs warning: maximal mount count reached, running e2fsck is recommended VFS: Mounted root (ext2 filesystem). Freeing init memory: 112K SCSI device sda: 1953525168 512-byte hdwr sectors (1000205 MB) SCSI device sda: drive cache: write back SCSI device sda: 1953525168 512-byte hdwr sectors (1000205 MB) SCSI device sda: drive cache: write back sda: sda1 sda2 sda4 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 SCSI device sdb: 1953525168 512-byte hdwr sectors (1000205 MB) SCSI device sdb: drive cache: write back SCSI device sdb: 1953525168 512-byte hdwr sectors (1000205 MB) SCSI device sdb: drive cache: write back sdb: sdb1 sdb2 sdb4 Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0 usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver egiga0: mac address changed egiga0: link down egiga0: link up<5>, full duplex<5>, speed 100 Mbps<5> Adding 530104k swap on /dev/sda1. Priority:-1 extents:1 Adding 530104k swap on /dev/sdb1. Priority:-2 extents:1 kjournald starting. Commit interval 5 seconds EXT3 FS on sda4, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sdb4, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda2, internal journal EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sdb2, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda2, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sdb2, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda4, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sdb4, internal journal EXT3-fs: mounted filesystem with ordered data mode. Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered.
For info, I bought it in firmware version 1.07 and upgraded it to 1.08b01. That's all.
I'm absolutely sure of all that.
Last edited by mushanga (2010-03-07 21:10:28)
Offline
#7 2010-03-07 21:42:34
- bernd123
- Member
- Registered: 2010-03-07
- Posts: 12
Re: Native Debian without flashing the firmware - instructions and issues
mushanga wrote:
For info, I bought it in firmware version 1.07 and upgraded it to 1.08b01. That's all.
I'm absolutely sure of all that.
I'm running 1.06, so I'll upgrade to 1.08b01, maybe that gives a new U-Boot.
Offline
#8 2010-03-07 23:52:05
- mushanga
- Member
- Registered: 2009-06-26
- Posts: 46
Re: Native Debian without flashing the firmware - instructions and issues
Do not forget u-boot upgrade could also be in 1.07... And 1.08 final is out BTW, maybe better than the beta.
Anyway think twice before upgrading just for this reason.
Also, try the reloading approach instead of u-boot booting off memory. It could work better.
Offline
#9 2010-03-08 00:35:12
- bernd123
- Member
- Registered: 2010-03-07
- Posts: 12
Re: Native Debian without flashing the firmware - instructions and issues
mushanga wrote:
Do not forget u-boot upgrade could also be in 1.07... And 1.08 final is out BTW, maybe better than the beta.
Btw: is it even possible to upgrade U-Boot with firmware-updates?
mushanga wrote:
Anyway think twice before upgrading just for this reason.
Also, try the reloading approach instead of u-boot booting off memory. It could work better.
Already tried that, seems to make no difference.
Offline
#10 2010-03-08 01:00:46
- bernd123
- Member
- Registered: 2010-03-07
- Posts: 12
Re: Native Debian without flashing the firmware - instructions and issues
mushanga wrote:
Do not forget u-boot upgrade could also be in 1.07... And 1.08 final is out BTW, maybe better than the beta.
Anyway think twice before upgrading just for this reason.
Also, try the reloading approach instead of u-boot booting off memory. It could work better.
I flashed now 1.07 and 1.08 but U-Boot is still 1.1.1
Offline
#11 2010-03-08 12:30:39
- mushanga
- Member
- Registered: 2009-06-26
- Posts: 46
Re: Native Debian without flashing the firmware - instructions and issues
bernd123,
I know this little talk is moving away from the initial issue but I've been poking around and I've discovered that my u-boot is even older than yours!!
Code:
Tiromancino:~# cat /dev/mtd4 > u-boot.raw Tiromancino:~# strings u-boot.raw (...) U-Boot 1.1.1 (Oct 12 2007 - 17:19:14) Marvell version: 1.7.3.001 (...)
Till now I took for granted the version reported by dmesg (remember I don't have serial console access); wrong thoughts 
Maybe your HW is more recent than mine. It would explain a lot of things f4exb is experiencing with his also (see http://dns323.kood.org/forum/viewtopic.php?id=5460).
And before your start thinking of it, it could be VERY risky to downgrade your u-boot. If it becomes screwed up I think you have to have a JTAG access to restore it if u-boot doesn't even start.
Offline
#12 2010-03-08 21:52:37
- bernd123
- Member
- Registered: 2010-03-07
- Posts: 12
Re: Native Debian without flashing the firmware - instructions and issues
mushanga wrote:
bernd123,
I know this little talk is moving away from the initial issue but I've been poking around and I've discovered that my u-boot is even older than yours!!
Our U-Boot version seems to be the very same.
mushanga wrote:
bernd123,
Maybe your HW is more recent than mine. It would explain a lot of things f4exb is experiencing with his also (see http://dns323.kood.org/forum/viewtopic.php?id=5460).
And before your start thinking of it, it could be VERY risky to downgrade your u-boot. If it becomes screwed up I think you have to have a JTAG access to restore it if u-boot doesn't even start.
Meanwhile, I managed to get the Debian-Installer booting. The problem is in LED/GPIO-stuff. So building a kernel without CONFIG_LEDS_GPIO seems to work. Who needs LEDs anyway:)
Offline
#13 2010-03-09 13:32:16
- mushanga
- Member
- Registered: 2009-06-26
- Posts: 46
Re: Native Debian without flashing the firmware - instructions and issues
bernd123 wrote:
Our U-Boot version seems to be the very same.
Are you shure?
yours: U-Boot 1.1.1 (Feb 26 2009 - 11:33:03) Marvell version: 1.7.3.003
mine: U-Boot 1.1.1 (Oct 12 2007 - 17:19:14) Marvell version: 1.7.3.001
Anyway I don't think it is the source of the problem...
bernd123 wrote:
Meanwhile, I managed to get the Debian-Installer booting. The problem is in LED/GPIO-stuff. So building a kernel without CONFIG_LEDS_GPIO seems to work. Who needs LEDs anyway:)
Good news! That would mean C1 rev. have a different GPIO conf. for leds, that's all.
I'm glad you can boot a 2.6.32 kernel (it is a 2.6.32, right?).
Do you experience any issues with LAN BTW? My DNS cannot link at 100M with a 2.6.32 kernel.
Offline
#14 2010-03-09 16:03:52
- bernd123
- Member
- Registered: 2010-03-07
- Posts: 12
Re: Native Debian without flashing the firmware - instructions and issues
mushanga wrote:
bernd123 wrote:
Our U-Boot version seems to be the very same.
Are you shure?
yours: U-Boot 1.1.1 (Feb 26 2009 - 11:33:03) Marvell version: 1.7.3.003
mine: U-Boot 1.1.1 (Oct 12 2007 - 17:19:14) Marvell version: 1.7.3.001
Anyway I don't think it is the source of the problem...
Well, you seem to be right:)
mushanga wrote:
bernd123 wrote:
Meanwhile, I managed to get the Debian-Installer booting. The problem is in LED/GPIO-stuff. So building a kernel without CONFIG_LEDS_GPIO seems to work. Who needs LEDs anyway:)
Good news! That would mean C1 rev. have a different GPIO conf. for leds, that's all.
I'm glad you can boot a 2.6.32 kernel (it is a 2.6.32, right?).
Do you experience any issues with LAN BTW? My DNS cannot link at 100M with a 2.6.32 kernel.
I'm running 2.6.26-2-orion5x (Debian) and LAN does not work at all. mii-tool reports always a link but dhclient tells me the network is down.
I'm trying 2.6.33 right now.
Offline
#15 2010-03-09 17:34:31
- bernd123
- Member
- Registered: 2010-03-07
- Posts: 12
Re: Native Debian without flashing the firmware - instructions and issues
bernd123 wrote:
I'm trying 2.6.33 right now.
LAN is working on 2.6.33 (vanilla).
Offline
#16 2010-03-10 00:50:10
- juhog
- Member
- Registered: 2010-03-05
- Posts: 9
Re: Native Debian without flashing the firmware - instructions and issues
I tried 2.6.33 (experimental) from Debian now and it is just like the 2.6.32 kernel I tried earlier, LAN does not work.
Code:
Mar 9 22:15:59 dns-siika kernel: imklog 3.18.6, log source = /proc/kmsg started. Mar 9 22:15:59 dns-siika rsyslogd: [origin software="rsyslogd" swVersion="3.18.6" x-pid="1125" x-info="http://www.rsyslog.com"] restart Mar 9 22:15:59 dns-siika kernel: [ 0.000000] Initializing cgroup subsys cpuset Mar 9 22:15:59 dns-siika kernel: [ 0.000000] Initializing cgroup subsys cpu Mar 9 22:15:59 dns-siika kernel: [ 0.000000] Linux version 2.6.33-2-orion5x (Debian 2.6.33-1~experimental.2) (maks@debian.org) (gcc version 4.3.4 (Debian 4.3.4-6) ) #1 Wed Mar 3 06:50:40 UTC 2010 Mar 9 22:15:59 dns-siika kernel: [ 0.000000] CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177 Mar 9 22:15:59 dns-siika kernel: [ 0.000000] CPU: VIVT data cache, VIVT instruction cache Mar 9 22:15:59 dns-siika kernel: [ 0.000000] Machine: D-Link DNS-323 Mar 9 22:15:59 dns-siika kernel: [ 0.000000] Memory policy: ECC disabled, Data cache writeback Mar 9 22:15:59 dns-siika kernel: [ 0.000000] On node 0 totalpages: 16384 Mar 9 22:15:59 dns-siika kernel: [ 0.000000] free_area_init_node: node 0, pgdat c037f93c, node_mem_map c03e7000 Mar 9 22:15:59 dns-siika kernel: [ 0.000000] Normal zone: 128 pages used for memmap Mar 9 22:15:59 dns-siika kernel: [ 0.000000] Normal zone: 0 pages reserved Mar 9 22:15:59 dns-siika kernel: [ 0.000000] Normal zone: 16256 pages, LIFO batch:3 Mar 9 22:15:59 dns-siika kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Mar 9 22:15:59 dns-siika kernel: [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda3 rootdelay=10 ip=192.168.0.100::192.168.0.1:255.255.255.0:dns-siika:eth0:none Mar 9 22:15:59 dns-siika kernel: [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) Mar 9 22:15:59 dns-siika kernel: [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Mar 9 22:15:59 dns-siika kernel: [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Mar 9 22:15:59 dns-siika kernel: [ 0.000000] Memory: 64MB = 64MB total Mar 9 22:15:59 dns-siika kernel: [ 0.000000] Memory: 58420KB available (3192K code, 564K data, 120K init, 0K highmem) Mar 9 22:15:59 dns-siika kernel: [ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Mar 9 22:15:59 dns-siika kernel: [ 0.000000] Hierarchical RCU implementation. Mar 9 22:15:59 dns-siika kernel: [ 0.000000] NR_IRQS:64 Mar 9 22:15:59 dns-siika kernel: [ 0.000000] Console: colour dummy device 80x30 Mar 9 22:15:59 dns-siika kernel: [ 25.770053] Calibrating delay loop... 332.59 BogoMIPS (lpj=1662976) Mar 9 22:15:59 dns-siika kernel: [ 25.989973] Security Framework initialized Mar 9 22:15:59 dns-siika kernel: [ 25.990016] SELinux: Disabled at boot. Mar 9 22:15:59 dns-siika kernel: [ 25.990083] Mount-cache hash table entries: 512 Mar 9 22:15:59 dns-siika kernel: [ 25.990671] Initializing cgroup subsys ns Mar 9 22:15:59 dns-siika kernel: [ 25.990704] Initializing cgroup subsys cpuacct Mar 9 22:15:59 dns-siika kernel: [ 25.990730] Initializing cgroup subsys devices Mar 9 22:15:59 dns-siika kernel: [ 25.990755] Initializing cgroup subsys freezer Mar 9 22:15:59 dns-siika kernel: [ 25.990779] Initializing cgroup subsys net_cls Mar 9 22:15:59 dns-siika kernel: [ 25.990882] CPU: Testing write buffer coherency: ok Mar 9 22:15:59 dns-siika kernel: [ 25.992494] devtmpfs: initialized Mar 9 22:15:59 dns-siika kernel: [ 25.994600] regulator: core version 0.5 Mar 9 22:15:59 dns-siika kernel: [ 25.994917] NET: Registered protocol family 16 Mar 9 22:15:59 dns-siika kernel: [ 25.995898] Orion ID: MV88F5182-A2. TCLK=166666667. Mar 9 22:15:59 dns-siika kernel: [ 25.996625] DNS323: Found ethernet MAC address: 00:21:91:57:50:28. Mar 9 22:15:59 dns-siika kernel: [ 26.001191] bio: create slab <bio-0> at 0 Mar 9 22:15:59 dns-siika kernel: [ 26.001933] vgaarb: loaded Mar 9 22:15:59 dns-siika kernel: [ 26.003153] Switching to clocksource orion_clocksource Mar 9 22:15:59 dns-siika kernel: [ 26.015156] NET: Registered protocol family 2 Mar 9 22:15:59 dns-siika kernel: [ 26.015507] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) Mar 9 22:15:59 dns-siika kernel: [ 26.016673] TCP established hash table entries: 2048 (order: 2, 16384 bytes) Mar 9 22:15:59 dns-siika kernel: [ 26.016788] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) Mar 9 22:15:59 dns-siika kernel: [ 26.016854] TCP: Hash tables configured (established 2048 bind 2048) Mar 9 22:15:59 dns-siika kernel: [ 26.016877] TCP reno registered Mar 9 22:15:59 dns-siika kernel: [ 26.016907] UDP hash table entries: 256 (order: 0, 4096 bytes) Mar 9 22:15:59 dns-siika kernel: [ 26.016963] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) Mar 9 22:15:59 dns-siika kernel: [ 26.017325] NET: Registered protocol family 1 Mar 9 22:15:59 dns-siika kernel: [ 26.017400] PCI: CLS 0 bytes, default 32 Mar 9 22:15:59 dns-siika kernel: [ 26.017784] Unpacking initramfs... Mar 9 22:15:59 dns-siika kernel: [ 26.443095] Freeing initrd memory: 2492K Mar 9 22:15:59 dns-siika kernel: [ 26.443351] NetWinder Floating Point Emulator V0.97 (double precision) Mar 9 22:15:59 dns-siika kernel: [ 26.443964] audit: initializing netlink socket (disabled) Mar 9 22:15:59 dns-siika kernel: [ 26.444056] type=2000 audit(0.670:1): initialized Mar 9 22:15:59 dns-siika kernel: [ 26.460415] VFS: Disk quotas dquot_6.5.2 Mar 9 22:15:59 dns-siika kernel: [ 26.460987] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Mar 9 22:15:59 dns-siika kernel: [ 26.461268] msgmni has been set to 119 Mar 9 22:15:59 dns-siika kernel: [ 26.462804] alg: No test for stdrng (krng) Mar 9 22:15:59 dns-siika kernel: [ 26.463117] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) Mar 9 22:15:59 dns-siika kernel: [ 26.463151] io scheduler noop registered Mar 9 22:15:59 dns-siika kernel: [ 26.463170] io scheduler deadline registered Mar 9 22:15:59 dns-siika kernel: [ 26.464189] io scheduler cfq registered (default) Mar 9 22:15:59 dns-siika kernel: [ 26.479375] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled Mar 9 22:15:59 dns-siika kernel: [ 26.480415] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A Mar 9 22:15:59 dns-siika kernel: [ 26.799335] console [ttyS0] enabled Mar 9 22:15:59 dns-siika kernel: [ 26.803907] physmap platform flash device: 00800000 at f4000000 Mar 9 22:15:59 dns-siika kernel: [ 26.810104] physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank Mar 9 22:15:59 dns-siika kernel: [ 26.816669] Amd/Fujitsu Extended Query Table at 0x0040 Mar 9 22:15:59 dns-siika kernel: [ 26.821907] number of CFI chips: 1 Mar 9 22:15:59 dns-siika kernel: [ 26.874001] RedBoot partition parsing not available Mar 9 22:15:59 dns-siika kernel: [ 26.878884] Using physmap partition information Mar 9 22:15:59 dns-siika kernel: [ 26.883475] Creating 5 MTD partitions on "physmap-flash.0": Mar 9 22:15:59 dns-siika kernel: [ 26.889048] 0x000000000000-0x000000010000 : "MTD1" Mar 9 22:15:59 dns-siika kernel: [ 26.895232] 0x000000010000-0x000000020000 : "MTD2" Mar 9 22:15:59 dns-siika kernel: [ 26.901155] 0x000000020000-0x0000001a0000 : "Linux Kernel" Mar 9 22:15:59 dns-siika kernel: [ 26.907828] 0x0000001a0000-0x0000007d0000 : "File System" Mar 9 22:15:59 dns-siika kernel: [ 26.914510] 0x0000007d0000-0x000000800000 : "u-boot" Mar 9 22:15:59 dns-siika kernel: [ 26.921437] mice: PS/2 mouse device common for all mice Mar 9 22:15:59 dns-siika kernel: [ 26.927660] i2c /dev entries driver Mar 9 22:15:59 dns-siika kernel: [ 26.931994] rtc-m41t80 0-0068: chip found, driver version 0.05 Mar 9 22:15:59 dns-siika kernel: [ 26.938349] rtc-m41t80 0-0068: rtc core: registered m41t80 as rtc0 Mar 9 22:15:59 dns-siika kernel: [ 26.946000] Registered led device: power:blue Mar 9 22:15:59 dns-siika kernel: [ 26.950492] Registered led device: right:amber Mar 9 22:15:59 dns-siika kernel: [ 26.955164] Registered led device: left:amber Mar 9 22:15:59 dns-siika kernel: [ 26.961756] TCP cubic registered Mar 9 22:15:59 dns-siika kernel: [ 26.965053] NET: Registered protocol family 17 Mar 9 22:15:59 dns-siika kernel: [ 26.969528] VFP support v0.3: not present Mar 9 22:15:59 dns-siika kernel: [ 26.974330] registered taskstats version 1 Mar 9 22:15:59 dns-siika kernel: [ 26.979535] rtc-m41t80 0-0068: setting system clock to 2010-03-09 22:15:13 UTC (1268172913) Mar 9 22:15:59 dns-siika kernel: [ 26.988038] Freeing init memory: 120K Mar 9 22:15:59 dns-siika kernel: [ 27.635973] SCSI subsystem initialized Mar 9 22:15:59 dns-siika kernel: [ 27.820710] usbcore: registered new interface driver usbfs Mar 9 22:15:59 dns-siika kernel: [ 27.826447] usbcore: registered new interface driver hub Mar 9 22:15:59 dns-siika kernel: [ 27.832056] usbcore: registered new device driver usb Mar 9 22:15:59 dns-siika kernel: [ 27.902261] Initializing USB Mass Storage driver... Mar 9 22:15:59 dns-siika kernel: [ 27.907392] usbcore: registered new interface driver usb-storage Mar 9 22:15:59 dns-siika kernel: [ 27.913446] USB Mass Storage support registered. Mar 9 22:15:59 dns-siika kernel: [ 28.041644] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Mar 9 22:15:59 dns-siika kernel: [ 28.048348] orion-ehci orion-ehci.0: Marvell Orion EHCI Mar 9 22:15:59 dns-siika kernel: [ 28.053757] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 Mar 9 22:15:59 dns-siika kernel: [ 28.083313] orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000 Mar 9 22:15:59 dns-siika kernel: [ 28.103275] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 Mar 9 22:15:59 dns-siika kernel: [ 28.109335] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 Mar 9 22:15:59 dns-siika kernel: [ 28.116172] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Mar 9 22:15:59 dns-siika kernel: [ 28.123420] usb usb1: Product: Marvell Orion EHCI Mar 9 22:15:59 dns-siika kernel: [ 28.128119] usb usb1: Manufacturer: Linux 2.6.33-2-orion5x ehci_hcd Mar 9 22:15:59 dns-siika kernel: [ 28.134407] usb usb1: SerialNumber: orion-ehci.0 Mar 9 22:15:59 dns-siika kernel: [ 28.139938] hub 1-0:1.0: USB hub found Mar 9 22:15:59 dns-siika kernel: [ 28.143781] hub 1-0:1.0: 1 port detected Mar 9 22:15:59 dns-siika kernel: [ 28.468356] usb 1-1: new high speed USB device using orion-ehci and address 2 Mar 9 22:15:59 dns-siika kernel: [ 28.635875] usb 1-1: New USB device found, idVendor=152d, idProduct=2336 Mar 9 22:15:59 dns-siika kernel: [ 28.642584] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5 Mar 9 22:15:59 dns-siika kernel: [ 28.649835] usb 1-1: Product: JM20336 SATA, USB Combo Mar 9 22:15:59 dns-siika kernel: [ 28.654940] usb 1-1: Manufacturer: JMicron Mar 9 22:15:59 dns-siika kernel: [ 28.659038] usb 1-1: SerialNumber: 888888D88CA8 Mar 9 22:15:59 dns-siika kernel: [ 28.796838] scsi0 : usb-storage 1-1:1.0 Mar 9 22:15:59 dns-siika kernel: [ 33.815143] scsi 0:0:0:0: Direct-Access WDC WD50 WD-WCAS8053 12.0 PQ: 0 ANSI: 2 CCS Mar 9 22:15:59 dns-siika kernel: [ 33.966080] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) Mar 9 22:15:59 dns-siika kernel: [ 33.977926] sd 0:0:0:0: [sda] Write Protect is off Mar 9 22:15:59 dns-siika kernel: [ 33.982727] sd 0:0:0:0: [sda] Mode Sense: 00 38 00 00 Mar 9 22:15:59 dns-siika kernel: [ 33.982752] sd 0:0:0:0: [sda] Assuming drive cache: write through Mar 9 22:15:59 dns-siika kernel: [ 33.991161] sd 0:0:0:0: [sda] Assuming drive cache: write through Mar 9 22:15:59 dns-siika kernel: [ 33.997356] sda: sda1 sda2 sda3 sda4 < sda5 > Mar 9 22:15:59 dns-siika kernel: [ 34.052561] sd 0:0:0:0: [sda] Assuming drive cache: write through Mar 9 22:15:59 dns-siika kernel: [ 34.058758] sd 0:0:0:0: [sda] Attached SCSI disk Mar 9 22:15:59 dns-siika kernel: [ 40.704123] md: raid1 personality registered for level 1 Mar 9 22:15:59 dns-siika kernel: [ 40.805896] md: md0 stopped. Mar 9 22:15:59 dns-siika kernel: [ 41.713414] kjournald starting. Commit interval 5 seconds Mar 9 22:15:59 dns-siika kernel: [ 41.719030] EXT3-fs (sda3): mounted filesystem with ordered data mode Mar 9 22:15:59 dns-siika kernel: [ 45.078047] udevd version 125 started Mar 9 22:15:59 dns-siika kernel: [ 53.487916] input: gpio-keys as /devices/platform/gpio-keys/input/input0 Mar 9 22:15:59 dns-siika kernel: [ 53.879562] libata version 3.00 loaded. Mar 9 22:15:59 dns-siika kernel: [ 53.900564] lm75 0-0048: hwmon0: sensor 'lm75' Mar 9 22:15:59 dns-siika kernel: [ 54.028750] MV-643xx 10/100/1000 ethernet driver version 1.4 Mar 9 22:15:59 dns-siika kernel: [ 54.099365] mv643xx_eth smi: probed Mar 9 22:15:59 dns-siika kernel: [ 54.124927] net eth0: port 0 with MAC address 00:21:91:57:50:28 Mar 9 22:15:59 dns-siika kernel: [ 54.193684] sata_mv sata_mv.0: version 1.28 Mar 9 22:15:59 dns-siika kernel: [ 54.198876] sata_mv sata_mv.0: slots 32 ports 2 Mar 9 22:15:59 dns-siika kernel: [ 54.274952] scsi1 : sata_mv Mar 9 22:15:59 dns-siika kernel: [ 54.283415] scsi2 : sata_mv Mar 9 22:15:59 dns-siika kernel: [ 54.293390] ata1: SATA max UDMA/133 irq 29 Mar 9 22:15:59 dns-siika kernel: [ 54.297495] ata2: SATA max UDMA/133 irq 29 Mar 9 22:15:59 dns-siika kernel: [ 54.813315] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Mar 9 22:15:59 dns-siika kernel: [ 54.853381] ata1.00: ATA-8: WDC WD20EADS-00S2B0, 01.00A01, max UDMA/133 Mar 9 22:15:59 dns-siika kernel: [ 54.859995] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) Mar 9 22:15:59 dns-siika kernel: [ 54.923499] ata1.00: configured for UDMA/133 Mar 9 22:15:59 dns-siika kernel: [ 54.928470] scsi 1:0:0:0: Direct-Access ATA WDC WD20EADS-00S 01.0 PQ: 0 ANSI: 5 Mar 9 22:15:59 dns-siika kernel: [ 54.960843] sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) Mar 9 22:15:59 dns-siika kernel: [ 54.984168] sd 1:0:0:0: [sdb] Write Protect is off Mar 9 22:15:59 dns-siika kernel: [ 54.988973] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 Mar 9 22:15:59 dns-siika kernel: [ 55.003292] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 9 22:15:59 dns-siika kernel: [ 55.024718] sdb: sdb1 sdb2 sdb4 Mar 9 22:15:59 dns-siika kernel: [ 55.054821] sd 1:0:0:0: [sdb] Attached SCSI disk Mar 9 22:15:59 dns-siika kernel: [ 55.463303] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Mar 9 22:15:59 dns-siika kernel: [ 55.503365] ata2.00: ATA-8: WDC WD20EADS-00R6B0, 01.00A01, max UDMA/133 Mar 9 22:15:59 dns-siika kernel: [ 55.509981] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) Mar 9 22:15:59 dns-siika kernel: [ 55.553462] ata2.00: configured for UDMA/133 Mar 9 22:15:59 dns-siika kernel: [ 55.558475] scsi 2:0:0:0: Direct-Access ATA WDC WD20EADS-00R 01.0 PQ: 0 ANSI: 5 Mar 9 22:15:59 dns-siika kernel: [ 55.570954] sd 2:0:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) Mar 9 22:15:59 dns-siika kernel: [ 55.582629] sd 2:0:0:0: [sdc] Write Protect is off Mar 9 22:15:59 dns-siika kernel: [ 55.587511] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 Mar 9 22:15:59 dns-siika kernel: [ 55.587913] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 9 22:15:59 dns-siika kernel: [ 55.599138] sdc: sdc1 sdc2 sdc4 Mar 9 22:15:59 dns-siika kernel: [ 56.026432] sd 2:0:0:0: [sdc] Attached SCSI disk Mar 9 22:15:59 dns-siika kernel: [ 60.161288] Adding 176672k swap on /dev/sda5. Priority:-1 extents:1 across:176672k Mar 9 22:15:59 dns-siika kernel: [ 62.597964] EXT3-fs (sda3): using internal journal Mar 9 22:15:59 dns-siika kernel: [ 65.030635] loop: module loaded Mar 9 22:15:59 dns-siika kernel: [ 65.745203] md: md0 stopped. Mar 9 22:15:59 dns-siika kernel: [ 65.856186] md: bind<sdc2> Mar 9 22:15:59 dns-siika kernel: [ 65.859491] md: bind<sdb2> Mar 9 22:15:59 dns-siika kernel: [ 66.564928] raid1: raid set md0 active with 2 out of 2 mirrors Mar 9 22:15:59 dns-siika kernel: [ 66.570974] md0: detected capacity change from 0 to 1998241202176 Mar 9 22:15:59 dns-siika kernel: [ 66.581150] md0: unknown partition table Mar 9 22:16:00 dns-siika kernel: [ 73.849865] eth0: link up, 1000 Mb/s, full duplex, flow control disabled Mar 9 22:16:01 dns-siika kernel: [ 74.798995] NET: Registered protocol family 10 Mar 9 22:16:01 dns-siika kernel: [ 74.819468] lo: Disabled Privacy Extensions Mar 9 22:16:05 dns-siika dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9 Mar 9 22:16:06 dns-siika /usr/sbin/cron[1460]: (CRON) INFO (pidfile fd = 3) Mar 9 22:16:06 dns-siika /usr/sbin/cron[1461]: (CRON) STARTUP (fork ok) Mar 9 22:16:06 dns-siika /usr/sbin/cron[1461]: (CRON) INFO (Running @reboot jobs) Mar 9 22:16:12 dns-siika kernel: [ 85.743247] eth0: no IPv6 routers present Mar 9 22:16:14 dns-siika dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 9 Mar 9 22:16:23 dns-siika dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11 Mar 9 22:16:34 dns-siika dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 10 Mar 9 22:16:44 dns-siika dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15 Mar 9 22:16:59 dns-siika dhclient: No DHCPOFFERS received. Mar 9 22:16:59 dns-siika dhclient: No working leases in persistent database - sleeping. Mar 9 22:17:01 dns-siika /USR/SBIN/CRON[1507]: (root) CMD ( cd / && run-parts --report /etc/cron.hourly)
bernd123 wrote:
bernd123 wrote:
I'm trying 2.6.33 right now.
LAN is working on 2.6.33 (vanilla).
Any chance to see your kernel .config and syslog?
Offline
#17 2010-03-10 03:07:18
- bernd123
- Member
- Registered: 2010-03-07
- Posts: 12
Re: Native Debian without flashing the firmware - instructions and issues
juhog wrote:
Any chance to see your kernel .config and syslog?
Here it is. I changed the mac-address in the dmesg.
Code:
[ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.33-orion5x (root@somehost) (gcc version 4.3.2 (Debian 4.3.2-1.1) ) #2 Tue Mar 9 14:30:30 UTC 2010 [ 0.000000] CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177 [ 0.000000] CPU: VIVT data cache, VIVT instruction cache [ 0.000000] Machine: D-Link DNS-323 [ 0.000000] Clearing invalid memory bank 0KB@0xffffffff [ 0.000000] Clearing invalid memory bank 0KB@0xffffffff [ 0.000000] Clearing invalid memory bank 0KB@0xffffffff [ 0.000000] Ignoring unrecognised tag 0x00000000 [ 0.000000] Ignoring unrecognised tag 0x00000000 [ 0.000000] Ignoring unrecognised tag 0x00000000 [ 0.000000] Ignoring unrecognised tag 0x41000403 [ 0.000000] Memory policy: ECC disabled, Data cache writeback [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat c030513c, node_mem_map c0337000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16256 pages, LIFO batch:3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 64MB = 64MB total [ 0.000000] Memory: 58376KB available (2800K code, 326K data, 124K init, 0K highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] RCU-based detection of stalled CPUs is enabled. [ 0.000000] NR_IRQS:64 [ 0.000000] Console: colour dummy device 80x30 [ 0.000341] Calibrating delay loop... 332.59 BogoMIPS (lpj=1662976) [ 0.220343] Security Framework initialized [ 0.220510] Mount-cache hash table entries: 512 [ 0.221189] Initializing cgroup subsys ns [ 0.221219] Initializing cgroup subsys cpuacct [ 0.221241] Initializing cgroup subsys devices [ 0.221355] CPU: Testing write buffer coherency: ok [ 0.225613] NET: Registered protocol family 16 [ 0.229605] Orion ID: MV88F5182-A2. TCLK=166666667. [ 0.231789] DNS323: Found ethernet MAC address: 00:26:5a:80:ff:ff. [ 0.249502] bio: create slab <bio-0> at 0 [ 0.251854] vgaarb: loaded [ 0.254649] Switching to clocksource orion_clocksource [ 0.259231] NET: Registered protocol family 2 [ 0.259637] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.261193] TCP established hash table entries: 2048 (order: 2, 16384 bytes) [ 0.261309] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) [ 0.261375] TCP: Hash tables configured (established 2048 bind 2048) [ 0.261400] TCP reno registered [ 0.261434] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.261489] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.261951] NET: Registered protocol family 1 [ 0.262031] PCI: CLS 0 bytes, default 32 [ 0.262475] Trying to unpack rootfs image as initramfs... [ 1.122759] Freeing initrd memory: 3236K [ 1.123533] NetWinder Floating Point Emulator V0.97 (double precision) [ 1.125491] audit: initializing netlink socket (disabled) [ 1.125585] type=2000 audit(1.120:1): initialized [ 1.126710] VFS: Disk quotas dquot_6.5.2 [ 1.126937] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 1.127208] msgmni has been set to 120 [ 1.128282] alg: No test for stdrng (krng) [ 1.128855] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 1.128891] io scheduler noop registered [ 1.128910] io scheduler deadline registered [ 1.129025] io scheduler cfq registered (default) [ 1.161489] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.163628] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A [ 1.485729] console [ttyS0] enabled [ 1.509141] brd: module loaded [ 1.513251] physmap platform flash device: 00800000 at f4000000 [ 1.519712] physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank [ 1.526334] Amd/Fujitsu Extended Query Table at 0x0040 [ 1.531568] number of CFI chips: 1 [ 1.575620] RedBoot partition parsing not available [ 1.580496] Using physmap partition information [ 1.585099] Creating 5 MTD partitions on "physmap-flash.0": [ 1.590674] 0x000000000000-0x000000010000 : "MTD1" [ 1.596782] ftl_cs: FTL header not found. [ 1.602121] 0x000000010000-0x000000020000 : "MTD2" [ 1.608118] ftl_cs: FTL header not found. [ 1.613029] 0x000000020000-0x0000001a0000 : "Linux Kernel" [ 1.620114] ftl_cs: FTL header not found. [ 1.625112] 0x0000001a0000-0x0000007d0000 : "File System" [ 1.631970] ftl_cs: FTL header not found. [ 1.637022] 0x0000007d0000-0x000000800000 : "u-boot" [ 1.643133] ftl_cs: FTL header not found. [ 1.650227] mice: PS/2 mouse device common for all mice [ 1.658488] i2c /dev entries driver [ 1.664633] rtc-m41t80 0-0068: chip found, driver version 0.05 [ 1.671261] rtc-m41t80 0-0068: rtc core: registered m41t80 as rtc0 [ 1.681411] TCP cubic registered [ 1.684646] NET: Registered protocol family 17 [ 1.689229] VFP support v0.3: not present [ 1.694819] registered taskstats version 1 [ 1.700055] rtc-m41t80 0-0068: setting system clock to 2010-03-09 18:56:02 UTC (1268160962) [ 1.708622] Freeing init memory: 124K [ 2.356980] SCSI subsystem initialized [ 2.559016] usbcore: registered new interface driver usbfs [ 2.565410] usbcore: registered new interface driver hub [ 2.571256] usbcore: registered new device driver usb [ 2.646514] Initializing USB Mass Storage driver... [ 2.651892] usbcore: registered new interface driver usb-storage [ 2.658018] USB Mass Storage support registered. [ 2.784127] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.790810] orion-ehci orion-ehci.0: Marvell Orion EHCI [ 2.796195] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 [ 2.824779] orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000 [ 2.844747] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 [ 2.850778] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.857611] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.864863] usb usb1: Product: Marvell Orion EHCI [ 2.869560] usb usb1: Manufacturer: Linux 2.6.33-orion5x ehci_hcd [ 2.875679] usb usb1: SerialNumber: orion-ehci.0 [ 2.881671] hub 1-0:1.0: USB hub found [ 2.885526] hub 1-0:1.0: 1 port detected [ 3.204926] usb 1-1: new high speed USB device using orion-ehci and address 2 [ 3.376377] usb 1-1: New USB device found, idVendor=0781, idProduct=5151 [ 3.383082] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 3.390314] usb 1-1: Product: Cruzer Micro [ 3.394404] usb 1-1: Manufacturer: SanDisk [ 3.398547] usb 1-1: SerialNumber: 2908121B0D9ffff [ 3.510738] scsi0 : usb-storage 1-1:1.0 [ 5.755985] device-mapper: uevent: version 1.0.3 [ 5.767539] device-mapper: ioctl: 4.16.0-ioctl (2009-11-05) initialised: dm-devel@redhat.com [ 8.526129] scsi 0:0:0:0: Direct-Access SanDisk Cruzer Micro 8.02 PQ: 0 ANSI: 0 CCS [ 8.670694] sd 0:0:0:0: [sda] 7856127 512-byte logical blocks: (4.02 GB/3.74 GiB) [ 8.679392] sd 0:0:0:0: [sda] Write Protect is off [ 8.684191] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 08 [ 8.684216] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 8.694384] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 8.700556] sda: sda1 sda2 sda3 [ 8.715913] sd 0:0:0:0: [sda] Assuming drive cache: write through [ 8.722016] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 11.662442] udevd version 125 started [ 17.811225] MV-643xx 10/100/1000 ethernet driver version 1.4 [ 17.817111] mv643xx_eth smi: probed [ 17.925824] net eth0: port 0 with MAC address 00:26:5a:80:ff:ff [ 17.932642] input: gpio-keys as /class/input/input0 [ 18.754992] libata version 3.00 loaded. [ 18.814009] sata_mv sata_mv.0: version 1.28 [ 18.819278] sata_mv sata_mv.0: slots 32 ports 2 [ 18.904832] scsi1 : sata_mv [ 18.909309] scsi2 : sata_mv [ 18.912425] ata1: SATA max UDMA/133 irq 29 [ 18.916605] ata2: SATA max UDMA/133 irq 29 [ 19.434777] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 19.455139] ata1.00: ATA-7: SAMSUNG HD154UI, 1AG01118, max UDMA7 [ 19.461142] ata1.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32) [ 19.485252] ata1.00: configured for UDMA/133 [ 19.490236] scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD154UI 1AG0 PQ: 0 ANSI: 5 [ 19.504430] sd 1:0:0:0: [sdb] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB) [ 19.513174] sd 1:0:0:0: [sdb] Write Protect is off [ 19.518062] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 [ 19.518490] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 19.529510] sdb: sdb1 [ 19.555502] sd 1:0:0:0: [sdb] Attached SCSI disk [ 19.844791] ata2: SATA link down (SStatus 0 SControl 300) [ 22.437258] Adding 176704k swap on /dev/sda3. Priority:-1 extents:1 across:176704k [ 24.318233] loop: module loaded [ 32.184440] eth0: link up, 100 Mb/s, full duplex, flow control disabled [ 33.149932] NET: Registered protocol family 10 [ 33.157795] lo: Disabled Privacy Extensions [ 33.946065] eth0: link down [ 35.678797] eth0: link up, 100 Mb/s, full duplex, flow control disabled [ 36.852354] warning: `ntpd' uses 32-bit capabilities (legacy support in use) [ 44.154645] eth0: no IPv6 routers present
Offline
#18 2010-03-10 03:15:07
- bernd123
- Member
- Registered: 2010-03-07
- Posts: 12
Re: Native Debian without flashing the firmware - instructions and issues
Just because I noticed: Your mac-address is different from mine. Look it up here: <http://standards.ieee.org/regauth/oui/index.shtml>, but both registered by D-Link.
Offline
#19 2010-03-10 21:50:36
- juhog
- Member
- Registered: 2010-03-05
- Posts: 9
Re: Native Debian without flashing the firmware - instructions and issues
It seems that ffp-reloaded is unable to load the newer kernels properly. That means that the only way to load newer kernels is to first boot into quite recent kernel (in my case 2.6.26 from Debian) with ffp-reloaded and then use kexec to load the kernel one wants to use. If fonz does not improve his ffp-reloaded to support recent kernels, I guess the cleanest way to boot into new kernels would be building initial ramdisk that instantly reboots into newest kernel in /boot.
syslog with 2.6.33-2-orion5x (Debian 2.6.33-1~experimental.2) booted using kexec-tools-2.0.1
Code:
ar 10 21:25:06 dns-siika kernel: imklog 3.18.6, log source = /proc/kmsg started. Mar 10 21:25:06 dns-siika rsyslogd: [origin software="rsyslogd" swVersion="3.18.6" x-pid="1137" x-info="http://www.rsyslog.com"] restart Mar 10 21:25:06 dns-siika kernel: [ 0.000000] Initializing cgroup subsys cpuset Mar 10 21:25:06 dns-siika kernel: [ 0.000000] Initializing cgroup subsys cpu Mar 10 21:25:06 dns-siika kernel: [ 0.000000] Linux version 2.6.33-2-orion5x (Debian 2.6.33-1~experimental.2) (maks@debian.org) (gcc version 4.3.4 (Debian 4.3.4-6) ) #1 Wed Mar 3 06:50:40 UTC 2010 Mar 10 21:25:06 dns-siika kernel: [ 0.000000] CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177 Mar 10 21:25:06 dns-siika kernel: [ 0.000000] CPU: VIVT data cache, VIVT instruction cache Mar 10 21:25:06 dns-siika kernel: [ 0.000000] Machine: D-Link DNS-323 Mar 10 21:25:06 dns-siika kernel: [ 0.000000] Memory policy: ECC disabled, Data cache writeback Mar 10 21:25:06 dns-siika kernel: [ 0.000000] On node 0 totalpages: 16384 Mar 10 21:25:06 dns-siika kernel: [ 0.000000] free_area_init_node: node 0, pgdat c037f93c, node_mem_map c03e7000 Mar 10 21:25:06 dns-siika kernel: [ 0.000000] Normal zone: 128 pages used for memmap Mar 10 21:25:06 dns-siika kernel: [ 0.000000] Normal zone: 0 pages reserved Mar 10 21:25:06 dns-siika kernel: [ 0.000000] Normal zone: 16256 pages, LIFO batch:3 Mar 10 21:25:06 dns-siika kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Mar 10 21:25:06 dns-siika kernel: [ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda3 rootdelay=10 ip=192.168.0.100::192.168.0.1:255.255.255.0:dns-siika:eth0:none Mar 10 21:25:06 dns-siika kernel: [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) Mar 10 21:25:06 dns-siika kernel: [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Mar 10 21:25:06 dns-siika kernel: [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Mar 10 21:25:06 dns-siika kernel: [ 0.000000] Memory: 64MB = 64MB total Mar 10 21:25:06 dns-siika kernel: [ 0.000000] Memory: 58420KB available (3192K code, 564K data, 120K init, 0K highmem) Mar 10 21:25:06 dns-siika kernel: [ 0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Mar 10 21:25:06 dns-siika kernel: [ 0.000000] Hierarchical RCU implementation. Mar 10 21:25:06 dns-siika kernel: [ 0.000000] NR_IRQS:64 Mar 10 21:25:06 dns-siika kernel: [ 0.000000] Console: colour dummy device 80x30 Mar 10 21:25:06 dns-siika kernel: [ 0.000249] Calibrating delay loop... 332.59 BogoMIPS (lpj=1662976) Mar 10 21:25:06 dns-siika kernel: [ 0.220169] Security Framework initialized Mar 10 21:25:06 dns-siika kernel: [ 0.220212] SELinux: Disabled at boot. Mar 10 21:25:06 dns-siika kernel: [ 0.220279] Mount-cache hash table entries: 512 Mar 10 21:25:06 dns-siika kernel: [ 0.220867] Initializing cgroup subsys ns Mar 10 21:25:06 dns-siika kernel: [ 0.220900] Initializing cgroup subsys cpuacct Mar 10 21:25:06 dns-siika kernel: [ 0.220926] Initializing cgroup subsys devices Mar 10 21:25:06 dns-siika kernel: [ 0.220951] Initializing cgroup subsys freezer Mar 10 21:25:06 dns-siika kernel: [ 0.220975] Initializing cgroup subsys net_cls Mar 10 21:25:06 dns-siika kernel: [ 0.221077] CPU: Testing write buffer coherency: ok Mar 10 21:25:06 dns-siika kernel: [ 0.222689] devtmpfs: initialized Mar 10 21:25:06 dns-siika kernel: [ 0.224795] regulator: core version 0.5 Mar 10 21:25:06 dns-siika kernel: [ 0.225113] NET: Registered protocol family 16 Mar 10 21:25:06 dns-siika kernel: [ 0.226094] Orion ID: MV88F5182-A2. TCLK=166666667. Mar 10 21:25:06 dns-siika kernel: [ 0.226821] DNS323: Found ethernet MAC address: 00:21:91:57:50:28. Mar 10 21:25:06 dns-siika kernel: [ 0.231386] bio: create slab <bio-0> at 0 Mar 10 21:25:06 dns-siika kernel: [ 0.232129] vgaarb: loaded Mar 10 21:25:06 dns-siika kernel: [ 0.233350] Switching to clocksource orion_clocksource Mar 10 21:25:06 dns-siika kernel: [ 0.245352] NET: Registered protocol family 2 Mar 10 21:25:06 dns-siika kernel: [ 0.245704] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) Mar 10 21:25:06 dns-siika kernel: [ 0.246869] TCP established hash table entries: 2048 (order: 2, 16384 bytes) Mar 10 21:25:06 dns-siika kernel: [ 0.246985] TCP bind hash table entries: 2048 (order: 1, 8192 bytes) Mar 10 21:25:06 dns-siika kernel: [ 0.247050] TCP: Hash tables configured (established 2048 bind 2048) Mar 10 21:25:06 dns-siika kernel: [ 0.247074] TCP reno registered Mar 10 21:25:06 dns-siika kernel: [ 0.247104] UDP hash table entries: 256 (order: 0, 4096 bytes) Mar 10 21:25:06 dns-siika kernel: [ 0.247160] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) Mar 10 21:25:06 dns-siika kernel: [ 0.247522] NET: Registered protocol family 1 Mar 10 21:25:06 dns-siika kernel: [ 0.247597] PCI: CLS 0 bytes, default 32 Mar 10 21:25:06 dns-siika kernel: [ 0.247981] Unpacking initramfs... Mar 10 21:25:06 dns-siika kernel: [ 0.673230] Freeing initrd memory: 2492K Mar 10 21:25:06 dns-siika kernel: [ 0.673484] NetWinder Floating Point Emulator V0.97 (double precision) Mar 10 21:25:06 dns-siika kernel: [ 0.674103] audit: initializing netlink socket (disabled) Mar 10 21:25:06 dns-siika kernel: [ 0.674196] type=2000 audit(0.670:1): initialized Mar 10 21:25:06 dns-siika kernel: [ 0.690551] VFS: Disk quotas dquot_6.5.2 Mar 10 21:25:06 dns-siika kernel: [ 0.691124] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Mar 10 21:25:06 dns-siika kernel: [ 0.691405] msgmni has been set to 119 Mar 10 21:25:06 dns-siika kernel: [ 0.692940] alg: No test for stdrng (krng) Mar 10 21:25:06 dns-siika kernel: [ 0.693252] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) Mar 10 21:25:06 dns-siika kernel: [ 0.693286] io scheduler noop registered Mar 10 21:25:06 dns-siika kernel: [ 0.693305] io scheduler deadline registered Mar 10 21:25:06 dns-siika kernel: [ 0.694329] io scheduler cfq registered (default) Mar 10 21:25:06 dns-siika kernel: [ 0.709519] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled Mar 10 21:25:06 dns-siika kernel: [ 0.710558] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A Mar 10 21:25:06 dns-siika kernel: [ 1.029477] console [ttyS0] enabled Mar 10 21:25:06 dns-siika kernel: [ 1.034045] physmap platform flash device: 00800000 at f4000000 Mar 10 21:25:06 dns-siika kernel: [ 1.040245] physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank Mar 10 21:25:06 dns-siika kernel: [ 1.046810] Amd/Fujitsu Extended Query Table at 0x0040 Mar 10 21:25:06 dns-siika kernel: [ 1.052048] number of CFI chips: 1 Mar 10 21:25:06 dns-siika kernel: [ 1.104195] RedBoot partition parsing not available Mar 10 21:25:06 dns-siika kernel: [ 1.109078] Using physmap partition information Mar 10 21:25:06 dns-siika kernel: [ 1.113680] Creating 5 MTD partitions on "physmap-flash.0": Mar 10 21:25:06 dns-siika kernel: [ 1.119258] 0x000000000000-0x000000010000 : "MTD1" Mar 10 21:25:06 dns-siika kernel: [ 1.125444] 0x000000010000-0x000000020000 : "MTD2" Mar 10 21:25:06 dns-siika kernel: [ 1.131374] 0x000000020000-0x0000001a0000 : "Linux Kernel" Mar 10 21:25:06 dns-siika kernel: [ 1.138048] 0x0000001a0000-0x0000007d0000 : "File System" Mar 10 21:25:06 dns-siika kernel: [ 1.144738] 0x0000007d0000-0x000000800000 : "u-boot" Mar 10 21:25:06 dns-siika kernel: [ 1.151662] mice: PS/2 mouse device common for all mice Mar 10 21:25:06 dns-siika kernel: [ 1.157879] i2c /dev entries driver Mar 10 21:25:06 dns-siika kernel: [ 1.162213] rtc-m41t80 0-0068: chip found, driver version 0.05 Mar 10 21:25:06 dns-siika kernel: [ 1.168582] rtc-m41t80 0-0068: rtc core: registered m41t80 as rtc0 Mar 10 21:25:06 dns-siika kernel: [ 1.176240] Registered led device: power:blue Mar 10 21:25:06 dns-siika kernel: [ 1.180737] Registered led device: right:amber Mar 10 21:25:06 dns-siika kernel: [ 1.185408] Registered led device: left:amber Mar 10 21:25:06 dns-siika kernel: [ 1.192001] TCP cubic registered Mar 10 21:25:06 dns-siika kernel: [ 1.195298] NET: Registered protocol family 17 Mar 10 21:25:06 dns-siika kernel: [ 1.199772] VFP support v0.3: not present Mar 10 21:25:06 dns-siika kernel: [ 1.204584] registered taskstats version 1 Mar 10 21:25:06 dns-siika kernel: [ 1.209788] rtc-m41t80 0-0068: setting system clock to 2010-03-10 21:24:20 UTC (1268256260) Mar 10 21:25:06 dns-siika kernel: [ 1.218292] Freeing init memory: 120K Mar 10 21:25:06 dns-siika kernel: [ 1.866515] SCSI subsystem initialized Mar 10 21:25:06 dns-siika kernel: [ 2.051050] usbcore: registered new interface driver usbfs Mar 10 21:25:06 dns-siika kernel: [ 2.056783] usbcore: registered new interface driver hub Mar 10 21:25:06 dns-siika kernel: [ 2.062382] usbcore: registered new device driver usb Mar 10 21:25:06 dns-siika kernel: [ 2.132531] Initializing USB Mass Storage driver... Mar 10 21:25:06 dns-siika kernel: [ 2.137679] usbcore: registered new interface driver usb-storage Mar 10 21:25:06 dns-siika kernel: [ 2.143724] USB Mass Storage support registered. Mar 10 21:25:06 dns-siika kernel: [ 2.272177] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Mar 10 21:25:06 dns-siika kernel: [ 2.278870] orion-ehci orion-ehci.0: Marvell Orion EHCI Mar 10 21:25:06 dns-siika kernel: [ 2.284274] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 Mar 10 21:25:06 dns-siika kernel: [ 2.313492] orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000 Mar 10 21:25:06 dns-siika kernel: [ 2.333472] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00 Mar 10 21:25:06 dns-siika kernel: [ 2.339553] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 Mar 10 21:25:06 dns-siika kernel: [ 2.346381] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 Mar 10 21:25:06 dns-siika kernel: [ 2.353629] usb usb1: Product: Marvell Orion EHCI Mar 10 21:25:06 dns-siika kernel: [ 2.358330] usb usb1: Manufacturer: Linux 2.6.33-2-orion5x ehci_hcd Mar 10 21:25:06 dns-siika kernel: [ 2.364617] usb usb1: SerialNumber: orion-ehci.0 Mar 10 21:25:06 dns-siika kernel: [ 2.370141] hub 1-0:1.0: USB hub found Mar 10 21:25:06 dns-siika kernel: [ 2.373994] hub 1-0:1.0: 1 port detected Mar 10 21:25:06 dns-siika kernel: [ 2.693613] usb 1-1: new high speed USB device using orion-ehci and address 2 Mar 10 21:25:06 dns-siika kernel: [ 2.866041] usb 1-1: New USB device found, idVendor=152d, idProduct=2336 Mar 10 21:25:06 dns-siika kernel: [ 2.872743] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=5 Mar 10 21:25:06 dns-siika kernel: [ 2.880004] usb 1-1: Product: JM20336 SATA, USB Combo Mar 10 21:25:06 dns-siika kernel: [ 2.885114] usb 1-1: Manufacturer: JMicron Mar 10 21:25:06 dns-siika kernel: [ 2.889213] usb 1-1: SerialNumber: 888888D88CA8 Mar 10 21:25:06 dns-siika kernel: [ 3.013809] scsi0 : usb-storage 1-1:1.0 Mar 10 21:25:06 dns-siika kernel: [ 8.035327] scsi 0:0:0:0: Direct-Access WDC WD50 WD-WCAS8053 12.0 PQ: 0 ANSI: 2 CCS Mar 10 21:25:06 dns-siika kernel: [ 8.184882] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) Mar 10 21:25:06 dns-siika kernel: [ 8.197905] sd 0:0:0:0: [sda] Write Protect is off Mar 10 21:25:06 dns-siika kernel: [ 8.202708] sd 0:0:0:0: [sda] Mode Sense: 00 38 00 00 Mar 10 21:25:06 dns-siika kernel: [ 8.202731] sd 0:0:0:0: [sda] Assuming drive cache: write through Mar 10 21:25:06 dns-siika kernel: [ 8.211093] sd 0:0:0:0: [sda] Assuming drive cache: write through Mar 10 21:25:06 dns-siika kernel: [ 8.217294] sda: sda1 sda2 sda3 sda4 < sda5 > Mar 10 21:25:06 dns-siika kernel: [ 8.270130] sd 0:0:0:0: [sda] Assuming drive cache: write through Mar 10 21:25:06 dns-siika kernel: [ 8.276332] sd 0:0:0:0: [sda] Attached SCSI disk Mar 10 21:25:06 dns-siika kernel: [ 14.955141] md: raid1 personality registered for level 1 Mar 10 21:25:06 dns-siika kernel: [ 15.056801] md: md0 stopped. Mar 10 21:25:06 dns-siika kernel: [ 15.944532] EXT3-fs (sda3): recovery required on readonly filesystem Mar 10 21:25:06 dns-siika kernel: [ 15.951002] EXT3-fs (sda3): write access will be enabled during recovery Mar 10 21:25:06 dns-siika kernel: [ 16.201957] kjournald starting. Commit interval 5 seconds Mar 10 21:25:06 dns-siika kernel: [ 16.207506] EXT3-fs (sda3): recovery complete Mar 10 21:25:06 dns-siika kernel: [ 16.215639] EXT3-fs (sda3): mounted filesystem with ordered data mode Mar 10 21:25:06 dns-siika kernel: [ 19.644547] udevd version 125 started Mar 10 21:25:06 dns-siika kernel: [ 28.021694] input: gpio-keys as /devices/platform/gpio-keys/input/input0 Mar 10 21:25:06 dns-siika kernel: [ 28.161125] MV-643xx 10/100/1000 ethernet driver version 1.4 Mar 10 21:25:06 dns-siika kernel: [ 28.191682] mv643xx_eth smi: probed Mar 10 21:25:06 dns-siika kernel: [ 28.446499] net eth0: port 0 with MAC address 00:21:91:57:50:28 Mar 10 21:25:06 dns-siika kernel: [ 28.508103] libata version 3.00 loaded. Mar 10 21:25:06 dns-siika kernel: [ 28.530925] lm75 0-0048: hwmon0: sensor 'lm75' Mar 10 21:25:06 dns-siika kernel: [ 28.770931] sata_mv sata_mv.0: version 1.28 Mar 10 21:25:06 dns-siika kernel: [ 28.811871] sata_mv sata_mv.0: slots 32 ports 2 Mar 10 21:25:06 dns-siika kernel: [ 28.823869] scsi1 : sata_mv Mar 10 21:25:06 dns-siika kernel: [ 28.836887] scsi2 : sata_mv Mar 10 21:25:06 dns-siika kernel: [ 28.845163] ata1: SATA max UDMA/133 irq 29 Mar 10 21:25:06 dns-siika kernel: [ 28.849269] ata2: SATA max UDMA/133 irq 29 Mar 10 21:25:06 dns-siika kernel: [ 29.373506] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Mar 10 21:25:06 dns-siika kernel: [ 29.413555] ata1.00: ATA-8: WDC WD20EADS-00S2B0, 01.00A01, max UDMA/133 Mar 10 21:25:06 dns-siika kernel: [ 29.420175] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) Mar 10 21:25:06 dns-siika kernel: [ 29.493724] ata1.00: configured for UDMA/133 Mar 10 21:25:06 dns-siika kernel: [ 29.498744] scsi 1:0:0:0: Direct-Access ATA WDC WD20EADS-00S 01.0 PQ: 0 ANSI: 5 Mar 10 21:25:06 dns-siika kernel: [ 29.531177] sd 1:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) Mar 10 21:25:06 dns-siika kernel: [ 29.554381] sd 1:0:0:0: [sdb] Write Protect is off Mar 10 21:25:06 dns-siika kernel: [ 29.559183] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00 Mar 10 21:25:06 dns-siika kernel: [ 29.563683] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 10 21:25:06 dns-siika kernel: [ 29.592191] sdb: sdb1 sdb2 sdb4 Mar 10 21:25:06 dns-siika kernel: [ 29.633905] sd 1:0:0:0: [sdb] Attached SCSI disk Mar 10 21:25:06 dns-siika kernel: [ 30.033498] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) Mar 10 21:25:06 dns-siika kernel: [ 30.073554] ata2.00: ATA-8: WDC WD20EADS-00R6B0, 01.00A01, max UDMA/133 Mar 10 21:25:06 dns-siika kernel: [ 30.080167] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) Mar 10 21:25:06 dns-siika kernel: [ 30.130177] ata2.00: configured for UDMA/133 Mar 10 21:25:06 dns-siika kernel: [ 30.135255] scsi 2:0:0:0: Direct-Access ATA WDC WD20EADS-00R 01.0 PQ: 0 ANSI: 5 Mar 10 21:25:06 dns-siika kernel: [ 30.162920] sd 2:0:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) Mar 10 21:25:06 dns-siika kernel: [ 30.174737] sd 2:0:0:0: [sdc] Write Protect is off Mar 10 21:25:06 dns-siika kernel: [ 30.179544] sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00 Mar 10 21:25:06 dns-siika kernel: [ 30.179927] sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 10 21:25:06 dns-siika kernel: [ 30.191004] sdc: sdc1 sdc2 sdc4 Mar 10 21:25:06 dns-siika kernel: [ 30.616988] sd 2:0:0:0: [sdc] Attached SCSI disk Mar 10 21:25:06 dns-siika kernel: [ 34.479104] Adding 176672k swap on /dev/sda5. Priority:-1 extents:1 across:176672k Mar 10 21:25:06 dns-siika kernel: [ 37.298146] EXT3-fs (sda3): using internal journal Mar 10 21:25:06 dns-siika kernel: [ 39.379332] loop: module loaded Mar 10 21:25:06 dns-siika kernel: [ 40.057627] md: md0 stopped. Mar 10 21:25:06 dns-siika kernel: [ 40.172738] md: bind<sdc2> Mar 10 21:25:06 dns-siika kernel: [ 40.176135] md: bind<sdb2> Mar 10 21:25:06 dns-siika kernel: [ 40.873986] raid1: raid set md0 active with 2 out of 2 mirrors Mar 10 21:25:06 dns-siika kernel: [ 40.880015] md0: detected capacity change from 0 to 1998241202176 Mar 10 21:25:06 dns-siika kernel: [ 40.890246] md0: unknown partition table Mar 10 21:25:06 dns-siika kernel: [ 47.233959] eth0: link up, 1000 Mb/s, full duplex, flow control disabled Mar 10 21:25:07 dns-siika dhclient: DHCPREQUEST on eth0 to 255.255.255.255 port 67 Mar 10 21:25:07 dns-siika dhclient: DHCPACK from 192.168.0.1 Mar 10 21:25:07 dns-siika dhclient: bound to 192.168.0.100 -- renewal in 879234540 seconds. Mar 10 21:25:08 dns-siika kernel: [ 49.680184] NET: Registered protocol family 10 Mar 10 21:25:08 dns-siika kernel: [ 49.700994] lo: Disabled Privacy Extensions Mar 10 21:25:14 dns-siika /usr/sbin/cron[1629]: (CRON) INFO (pidfile fd = 3) Mar 10 21:25:14 dns-siika /usr/sbin/cron[1630]: (CRON) STARTUP (fork ok) Mar 10 21:25:14 dns-siika /usr/sbin/cron[1630]: (CRON) INFO (Running @reboot jobs)
I guess all kernels will load correctly with kexec.
Offline
#20 2010-03-14 17:57:27
- juhog
- Member
- Registered: 2010-03-05
- Posts: 9
Re: Native Debian without flashing the firmware - instructions and issues
I will post some additional info related this topic to the second post in this thread, and update it when necessary.
Offline
#21 2010-03-14 19:03:22
- juhog
- Member
- Registered: 2010-03-05
- Posts: 9
Re: Native Debian without flashing the firmware - instructions and issues
Added the source code for bootloader creation script to 2nd post in this thread.
Offline
#22 2010-03-19 17:20:14
- mushanga
- Member
- Registered: 2009-06-26
- Posts: 46
Re: Native Debian without flashing the firmware - instructions and issues
Hi Juhog,
not that I want to rush you or ask too much but would you mind sharing also your binaries/kernel/image.
I don't have another linux box and I cannot generate the zImage/initrd you talk about.
Thanks in advance
Offline
#23 2010-03-23 22:34:31
- juhog
- Member
- Registered: 2010-03-05
- Posts: 9
Re: Native Debian without flashing the firmware - instructions and issues
mushanga wrote:
Hi Juhog,
not that I want to rush you or ask too much but would you mind sharing also your binaries/kernel/image.
I don't have another linux box and I cannot generate the zImage/initrd you talk about.
Thanks in advance
Oh, sorry, I had to postpone this project as I had some university work to do. I uploaded the binaries to http://krunde.net/~juho/ .
EDIT: I added some documentation to my upload directory aswell. Hopefully all the files are usable and beneficial to the community!
Last edited by juhog (2010-03-23 23:09:29)
Offline
#24 2010-03-24 00:47:11
- mushanga
- Member
- Registered: 2009-06-26
- Posts: 46
Re: Native Debian without flashing the firmware - instructions and issues
Thank you very much for all that!
Offline
Pages: 1
- Index
- » DNS-323/321 Discussion
- » Native Debian without flashing the firmware - instructions and issues