Unfortunately no one can be told what fun_plug is - you have to see it for yourself.
You are not logged in.
Hi - got my DNS-323 a week ago and have been happy to date. Have been trying to be a little bit more adventurous since i found this forum (i have very little unix experience).
Started off with the fun_plug - no probs
Then tried Telnet - here is where i am having problems
Have searched and read as many forum entries as i could but no matter what still can't get telnet to work. Have followed the instructions (many times) in telnet how to.
Have ensured that the krh files are loaded to Volume_1 - ensured that they have permissions (used command line / ws_ftp etc). Fun_plug is the one in krh .gz file.
All boots ok and dmesg.out is created etc - however when i try to use putty i get the following message:
network error: connection failed (similar message if i use command line) - note i have selected port 23
I have tried telnet from another pc and also tried port forwarding on my router all to no avail.
I even downloaded fw 1.3 from us site and applied today but no luck.
Any help greatly appreciated....
Offline
Start by disabling the port forwarding on your router, that's not the problem and you don't want it enabled because it's a security risk. Port forwarding is only used if you're establishing a connection from outside of your network.
If you're running a personal firewall on the PC try disabling it.
Last edited by fordem (2007-05-23 21:19:00)
Offline
I have the same issue: The dmesg file is created. But when I try to connect, putty justs shut down withouth any reason.
The instructions refers to /mnt/HD_a2, is this correct also when you run raid1 (two disk appears as one)?
I just don't get what I'm doing wrong. I'm used to connect to other sites, don't see how connecting to a server on same network should cause problems.
I'm connecting to the box's IP: I get Connection refused.
Last edited by bareare (2007-05-25 23:10:51)
Offline
This is the log:
Linux version 2.6.12.6-arm1 (jack@SWTEST2) (gcc version 3.3.3) #32 Tue Jan 23 17:11:52 CST 2007 CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ) CPU0: D VIVT write-back cache CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets Machine: MV-88fxx81 Using UBoot passing parameters structure Sys Clk = 166000000, Tclk = 166000000 - Warning - This LSP release was tested only with U-Boot release 1.7.3 Memory policy: ECC disabled, Data cache writeback On node 0 totalpages: 16384 DMA zone: 16384 pages, LIFO batch:7 Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 Built 1 zonelists Kernel command line: root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none PID hash table entries: 512 (order: 9, 8192 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 64MB 0MB 0MB 0MB = 64MB total Memory: 55936KB available (2466K code, 454K data, 112K init) Calibrating delay loop... 331.77 BogoMIPS (lpj=1658880) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 5826K NET: Registered protocol family 16 Marvell Development Board (LSP Version 1.7.6_NAS)-- RD-88F5181-88SX7042-2xSATA Detected Tclk 166000000 and SysClk 166000000 Marvell USB EHCI Host controller #0: c03ab980 pexBarOverlapDetect: winNum 2 overlap current 0 mvPexInit:Warning :Bar 2 size is illigal it will be disabled please check Pex and CPU windows configuration PCI: bus0: Fast back to back transfers disabled PCI: bus1: Fast back to back transfers enabled SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub cesadev_init(c0012498) Fast Floating Point Emulator V0.9 (c) Peter Teichmann. VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled ttyS0 at MMIO 0x0 (irq = 3) is a 16550A io scheduler noop registered io scheduler deadline registered RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize loop: loaded (max 8 devices) Marvell Gigabit Ethernet Driver 'egiga': o Ethernet descriptors in DRAM o DRAM SW cache-coherency o Checksum offload enabled o Loading network interface 'egiga0' scsi0 : Marvell SCSI to SATA adapter scsi1 : Marvell SCSI to SATA adapter scsi2 : Marvell SCSI to SATA adapter scsi3 : Marvell SCSI to SATA adapter Vendor: Seagate Model: ST3750640AS Rev: 3.AA Type: Direct-Access ANSI SCSI revision: 03 Vendor: Seagate Model: ST3750640AS Rev: 3.AA Type: Direct-Access ANSI SCSI revision: 03 Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0 Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0 physmap flash device: 800000 at ff800000 phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank Amd/Fujitsu Extended Query Table at 0x0040 number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. cmdlinepart partition parsing not available RedBoot partition parsing not available Using physmap partition definition Creating 5 MTD partitions on "phys_mapped_flash": 0x00000000-0x00010000 : "MTD1" 0x00010000-0x00020000 : "MTD2" 0x00020000-0x001a0000 : "Linux Kernel" 0x001a0000-0x007d0000 : "File System" 0x007d0000-0x00800000 : "u-boot" ehci_platform ehci_platform.20865: EHCI Host Controller ehci_platform ehci_platform.20865: new USB bus registered, assigned bus number 1 ehci_platform ehci_platform.20865: irq 17, io mem 0x00000000 ehci_platform ehci_platform.20865: park 0 ehci_platform ehci_platform.20865: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) usbcore: registered new driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver mice: PS/2 mouse device common for all mice md: linear personality registered as nr 1 md: raid0 personality registered as nr 2 md: raid1 personality registered as nr 3 md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 4Kbytes TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) NET: Registered protocol family 1 NET: Registered protocol family 17 md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. RAMDISK: Compressed image found at block 0 EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended VFS: Mounted root (ext2 filesystem). Freeing init memory: 112K SCSI device sda: 1465149168 512-byte hdwr sectors (750156 MB) SCSI device sda: drive cache: write back SCSI device sda: 1465149168 512-byte hdwr sectors (750156 MB) SCSI device sda: drive cache: write back sda: sda1 sda2 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 SCSI device sdb: 1465149168 512-byte hdwr sectors (750156 MB) SCSI device sdb: drive cache: write back SCSI device sdb: 1465149168 512-byte hdwr sectors (750156 MB) SCSI device sdb: drive cache: write back sdb: sdb1 sdb2 Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0 egiga0: mac address changed egiga0: link down egiga0: link up<5>, full duplex<5>, speed 100 Mbps<5> Adding 530104k swap on /dev/sda1. Priority:-1 extents:1 Adding 530104k swap on /dev/sdb1. Priority:-2 extents:1 md: bind<sda2> md: bind<sdb2> raid1: raid set md0 active with 2 out of 2 mirrors EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended md: md0 stopped. md: unbind<sdb2> md: export_rdev(sdb2) md: unbind<sda2> md: export_rdev(sda2) md: md1 stopped. md: bind<sda2> md: bind<sdb2> raid1: raid set md0 active with 2 out of 2 mirrors EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended Link Layer Topology Discovery Protocol, version 1.05.1223.2005 dev is <NULL>
Offline
When I found another plugin here with telnet instead of the first one I found, I got it to work.
Offline
Thanks bareare!!!!
I don't know how long i have wasted trying to get my telnet working....
You were right - i tried another lot of files - the RAR ones instead krh's and viola telnet working no probs...
Help appreciated greatly.
P.S don't know why the other files work for everybody else???
Offline