DSM-G600, DNS-3xx and NSA-220 Hack Forum

I guess it is better to refer to the MLD page for MLD related questions.

ultrabrutal wrote:

I get a warnings when uploading sh:

ftp> put d:\dns-323\mldonkey-2.8.7-dns-323\mlnet.sh
200 PORT command successful.
150 Opening ASCII mode data connection for mlnet.sh.
226-WARNING! 25 bare linefeeds received in ASCII mode
   File may not have transferred correctly.
226 Transfer complete.
ftp: 775 bytes sent in 0,00Seconds 775000,00Kbytes/sec.

And then an error when running script:

/mnt/HD_a2/fun_plug.d/start # chmod a+x mlnet.sh
/mnt/HD_a2/fun_plug.d/start # sh mlnet.sh
mlnet.sh: line 16: syntax error: "else" unexpected

Any ideas? Thanks

/mnt/HD_a2/fun_plug.d/start # ./mlnet.sh

just create a mldonkey directory under /mnt/HD_a2 as I think I did the if else check wrongly in the released mlnet.sh. Got to search on how to write a shell script.

wtf, after installing your software I cannot access the DNS-323 via SMB anymore. FTP still works.. And yes I did not change any settings and yes it's still enabled.

Any idea what can be causing this problem?  Can it be that after mlnet.sh is started nothing else is started?  Should I do the

/mnt/HD_a2/fun_plug.d/bin/mlnet.sh >/dev/null 2>/dev/null </dev/null &

Trick or something? Tnx

shadowandy wrote:

on default settings of MLD, I encountered the problem once. I tuned down to lower global connection and stuffs and I don't face the problem. Anyway, if you do read the wiki, you might find similar problem and its solution down there at http://dns323.kood.org/information:know … ter_reboot , hence the problem might or might not be due to the MLD.

I have had my DNS for a long time and never had any problems until I installed MLD. (upgraded to 1.03 firmware a week ago)

Wiki, I tried smb restart but it still does not work. I'm pretty sure the problem is MLD. I can easily test this if you want me to (by removing it again, reboot and see if SMB works again)

shadowandy wrote:

I am wondering, do ALL users who are using the MLD binary I compiled having samba problem after running MLD?

Any idea how many uses this?  It's such an important feature for a NAS I think. Everyone should use it

shadowandy wrote:

I guess I will stop releasing future compilations to public.

That truely would be sad if you decided to do that. Maybe someone else can chip in and get it running 100% stable?



Here is my fun_plug.log:

Tue Jun 12 11:51:58 GMT 2007
* /mnt/HD_a2/fun_plug.d/start/dropbear.sh not executable...
* /mnt/HD_a2/fun_plug.d/start/inetd.sh not executable...
* /mnt/HD_a2/fun_plug.d/start/lighttpd.sh not executable...
* Running /mnt/HD_a2/fun_plug.d/start/mlnet.sh...
chmod: /mnt/HD_a2/mldonkey/*: No such file or directory
* /mnt/HD_a2/fun_plug.d/start/rsyncd.sh not executable...
* Running /mnt/HD_a2/fun_plug.d/start/startmyfan.sh...
* Running /mnt/HD_a2/fun_plug.d/start/telnetd.sh...
Starting telnetd...
* /mnt/HD_a2/fun_plug.d/start/unfsd.sh not executable...
* Done

I see no indications that anything is going on with SMB. However there is a problem with mlnet.sh. Don't know if it matters or not.


Thanks again for the help and your work on this

Hey folks,

another quick question, I added the mlent to my fun_plug:

#
# Start the MLDonkey  Server
#
/mnt/HD_a2/mlnet.sh 1>>${LOGFILE} 2>&1



But when I reboot the nas MlDonkey is not running. The log shows this:

/bin/sh: Can't open nohup

But when I telnet into the DS-323 and run the same command by hand (/mnt/HD_a2/mlnet.sh) it works every time.  Do I just need to add a small delay? As its sooo close from working perfrectly for me

thanks and sorry for all the questions!

gbrugg wrote:

I also get the same problem as jbirney and have to start MLD by hand....

Well I got lucky, I added a 15 second sleep delay and tada its now starting when the NAS is rebooted automagicaly:

#
# Start the MLDonkey  Server
#
echo "Sleeping for 15 seconds..." >>${LOGFILE}
sleep 15
echo "Starting MLDonkey  Server..." >>${LOGFILE}
/mnt/HD_a2/mlnet.sh 1>>${LOGFILE} 2>&1


I have seen this happen before where you needed to wait for something else to fully start so yes its a hack and I got lucky but I will take it

Thanks again ShadowAndy!!!!!!!!!!!

Last edited by jbirney (2007-06-12 19:35:25)

jbirney wrote:

gbrugg wrote:

I also get the same problem as jbirney and have to start MLD by hand....

Well I got lucky, I added a 15 second sleep delay and tada its now starting when the NAS is rebooted automagicaly:

#
# Start the MLDonkey  Server
#
echo "Sleeping for 15 seconds..." >>${LOGFILE}
sleep 15
echo "Starting MLDonkey  Server..." >>${LOGFILE}
/mnt/HD_a2/mlnet.sh 1>>${LOGFILE} 2>&1


I have seen this happen before where you needed to wait for something else to fully start so yes its a hack and I got lucky but I will take it

Thanks again ShadowAndy!!!!!!!!!!!

Welcome. The sleep is pretty neat. I couldn't figure out why I cant get mlnet to autostart initially with 2.8.5. But it appears to autostart with 2.8.7 for me without the sleep line. Pretty weird. Probably will change the shell script to fonz's format.

Hi,
I have a problem. The mldonkey core not 100% working on my dns-323, if I start the core from lnx_bin just like shadowandy.
The core is working, i can connect the webpage and i can use sancho.
The problem is - with this core the torrent downloads stops at 98%, and the core cant finish the download.
If i'm starting the core inside etch - another install inside etch - the mldonkey working 100% - and it can finish my torrent donwloads.
Any idea ?

Thank's :

Craft

craft wrote:

Hi,
I have a problem. The mldonkey core not 100% working on my dns-323, if I start the core from lnx_bin just like shadowandy.
The core is working, i can connect the webpage and i can use sancho.
The problem is - with this core the torrent downloads stops at 98%, and the core cant finish the download.
If i'm starting the core inside etch - another install inside etch - the mldonkey working 100% - and it can finish my torrent donwloads.
Any idea ?

Thank's :

Craft

Does it happen for all torrents? Or there are insufficient seeders or peers to have a complete file?

Last edited by shadowandy (2007-06-14 18:09:28)

richneo wrote:

craft wrote:

Hi,
I have a problem. The mldonkey core not 100% working on my dns-323, if I start the core from lnx_bin just like shadowandy.
The core is working, i can connect the webpage and i can use sancho.
The problem is - with this core the torrent downloads stops at 98%, and the core cant finish the download.
If i'm starting the core inside etch - another install inside etch - the mldonkey working 100% - and it can finish my torrent donwloads.
Any idea ?

Thank's :

Craft

youre working at dlink? ^^

i have no problem running it thou my downloada can finish

Yes - for D-Link EE.

craft wrote:

richneo wrote:

craft wrote:

Hi,
I have a problem. The mldonkey core not 100% working on my dns-323, if I start the core from lnx_bin just like shadowandy.
The core is working, i can connect the webpage and i can use sancho.
The problem is - with this core the torrent downloads stops at 98%, and the core cant finish the download.
If i'm starting the core inside etch - another install inside etch - the mldonkey working 100% - and it can finish my torrent donwloads.
Any idea ?

Thank's :

Craft

youre working at dlink? ^^

i have no problem running it thou my downloada can finish

Yes - for D-Link EE.

u might want to pm me ur dlink email so we can communicate =p