DSM-G600, DNS-3xx and NSA-220 Hack Forum

Unfortunately no one can be told what fun_plug is - you have to see it for yourself.

You are not logged in.

Announcement

Pages: 1

 

#1 2007-07-16 00:01:05

Tester
Member
Registered: 2007-02-23
Posts: 23

How to recover or update firmware, manually w/o webinterface ???

Hi,

I need to rewrite the firmware, because the DNS has errors while booting and don't start correctly.

No ftp, no webinterface, only serial access.

I have to activate egiga0 manually also, but ftp access is not set correctly.



Code:

 ** LOADER **
 ** MARVELL BOARD: RD-88F5181-POS-NAS LE 

U-Boot 1.1.1 (Nov 13 2006 - 14:01:34) Marvell version: 1.4.2

DRAM CS[0] base 0x00000000   size  64MB 
DRAM Total size  64MB 
[8192kB@ff800000] Flash:  8 MB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
*** Warning - bad CRC, using default environment


Soc: MV88F5181 Rev 3
CPU: ARM926 (Rev 0) running @ 500Mhz 
SysClock = 166Mhz , TClock = 166Mhz 


 Init usb device.
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Hit any key to stop autoboot:  3  2  1  0 
## Booting image at ff820000 ...
   Image Name:   Linux-2.6.12.6-arm1
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1426456 Bytes =  1.4 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at ff9a0000 ...
   Image Name:   Ramdisk
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    5966305 Bytes =  5.7 MB
   Load Address: 00800000
   Entry Point:  00800000
   Verifying Checksum ... OK

Starting kernel ...

Uncompressing Linux............................................................................................... done, booting the kernel.

Linux version 2.6.12.6-arm1 (jack@SWTEST2) (gcc version 3.3.3) #32 Tue Jan 23 17:11:52 CST 2007

CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)

CPU0: D VIVT write-back cache

CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets

CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets

Machine: MV-88fxx81

Using UBoot passing parameters structure

Sys Clk = 166000000, Tclk = 166000000



- Warning - This LSP release was tested only with U-Boot release 1.7.3 


Memory policy: ECC disabled, Data cache writeback

Built 1 zonelists

Kernel command line: root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none

PID hash table entries: 512 (order: 9, 8192 bytes)

Console: colour dummy device 80x30

Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)

Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)

Memory: 64MB 0MB 0MB 0MB = 64MB total

Memory: 55936KB available (2466K code, 454K data, 112K init)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

checking if image is initramfs...it isn't (no cpio magic); looks like an initrd

Freeing initrd memory: 5826K

NET: Registered protocol family 16


  Marvell Development Board (LSP Version 1.7.6_NAS)-- RD-88F5181-88SX7042-2xSATA 


 Detected Tclk 166000000 and SysClk 166000000 

Marvell USB EHCI Host controller #0: c03ab980

pexBarOverlapDetect: winNum 2 overlap current 0

mvPexInit:Warning :Bar 2 size is illigal

it will be disabled

please check Pex and CPU windows configuration

PCI: bus0: Fast back to back transfers disabled

PCI: bus1: Fast back to back transfers enabled

SCSI subsystem initialized

usbcore: registered new driver usbfs

usbcore: registered new driver hub

cesadev_init(c0012498)

Fast Floating Point Emulator V0.9 (c) Peter Teichmann.

VFS: Disk quotas dquot_6.5.1

Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

Initializing Cryptographic API

Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled

ttyS0 at MMIO 0x0 (irq = 3) is a 16550A

io scheduler noop registered

io scheduler deadline registered

RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize

loop: loaded (max 8 devices)

Marvell Gigabit Ethernet Driver 'egiga':

  o Ethernet descriptors in DRAM

  o DRAM SW cache-coherency

  o Checksum offload enabled

  o Loading network interface 'egiga0' 

scsi0 : Marvell SCSI to SATA adapter

scsi1 : Marvell SCSI to SATA adapter

scsi2 : Marvell SCSI to SATA adapter

scsi3 : Marvell SCSI to SATA adapter

physmap flash device: 800000 at ff800000

phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank

 Amd/Fujitsu Extended Query Table at 0x0040

number of CFI chips: 1

cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.

cmdlinepart partition parsing not available

RedBoot partition parsing not available

Using physmap partition definition

Creating 5 MTD partitions on "phys_mapped_flash":

0x00000000-0x00010000 : "MTD1"

0x00010000-0x00020000 : "MTD2"

0x00020000-0x001a0000 : "Linux Kernel"

0x001a0000-0x007d0000 : "File System"

0x007d0000-0x00800000 : "u-boot"

ehci_platform ehci_platform.20865: EHCI Host Controller

ehci_platform ehci_platform.20865: new USB bus registered, assigned bus number 1

ehci_platform ehci_platform.20865: irq 17, io mem 0x00000000

ehci_platform ehci_platform.20865: park 0

ehci_platform ehci_platform.20865: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 1 port detected

usbcore: registered new driver usblp

drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver

mice: PS/2 mouse device common for all mice

md: linear personality registered as nr 1

md: raid0 personality registered as nr 2

md: raid1 personality registered as nr 3

md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27

device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com

NET: Registered protocol family 2

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP established hash table entries: 4096 (order: 3, 32768 bytes)

TCP bind hash table entries: 4096 (order: 2, 16384 bytes)

TCP: Hash tables configured (established 4096 bind 4096)

NET: Registered protocol family 1

NET: Registered protocol family 17

md: Autodetecting RAID arrays.

md: autorun ...

md: ... autorun DONE.

RAMDISK: Compressed image found at block 0

EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended

VFS: Mounted root (ext2 filesystem).

Freeing init memory: 112K


init started:  BusyBox v1.00-pre1 (2006.07.17-10:17+0000) multi-call binary

init started:  BusyBox v1.00-pre1 (2006.07.17-10:17+0000) multi-call binary

Starting pid 218, console /dev/ttyS0: '/etc/rc.sh'
Check MTD block device V2.01.05162006
MTDC: Mount MTD1 done.
cp: internal error: unrecognized file type
cp: internal error: unrecognized file type
cp: internal error: unrecognized file type
cp: internal error: unrecognizBad inode number on dev mtdblock0: 65535 is out of range

ed file type
cp: internal error: unrecognized file type
cp: internal error: unrecognized file type
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
MTDC: Mount MTD2 done.
Error: Can't open file /sys/mtd1/sib.conf in mtd1.
MTDC: Backup files from MTD1 to MTD2.
cp: internal error: unrecognized file type
cp: internal error: unrecognized file type
cp: internal error: unrecognized file type
cp: internal error: unrecognized file type
cp: internal error: unrecognized file type
cp: internal error: unrecognized file type
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
cp: /sys/mtd1/ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ: Input/output error
** Mounting /etc/fstab
umount: proc: not mounted
umount: proc: not mounted
umount: /image.cfs: not mounted
umount: /image.cfs: not mounted
** check raid Config version
Don't Update raidtab2web
** copy mtd1 files
cp: /sys/mtd1/sib.conf: No such file or directory
cp: /sys/mtd1/sib2.conf: No such file or directory
cp: /sys/mtd1/sib_ap.conf: No such file or directory
cp: /sys/mtd1/smbpasswd: No such file or directory
cp: /sys/mtd1/smb.default: No such file or directory
cp: /sys/mtd1/firmwareupdate: No such file or directory
cp: internal error: unrecognized file type
cp: internal error: unrecognized file type
cp: internal error: unrecognized file type
cp: /sys/mtd1/udhcpd.conf: No such file or directory
cp: internal error: unrecognized file type
cp: internal error: unrecognized file type
mv: /sys/mtd1/firmwareupdate: No such file or directory
mv: /sys/mtd1/restore: No such file or directory
mv: /sys/mtd1/format_ok: No such file or directory
mv: /sys/mtd1/pls_sync: No such file or directory
mv: /sys/mtd1/pls_chmod_a2: No such file or directory
mv: /sys/mtd1/pls_chmod_b2: No such file or directory
cp: internal error: unrecognized file type
** link lib **
** link web **
** link /usr/bin **
** link /usr/sbin **
** link /usr/local/LPRng **
<rtc>: getRTC time= 7/7/15 22:56:12
<fan script start>
** set loopback interface
MAC = 00:19:5B:77:9F:21
egiga0: mac address changed

** Activate Gigabit Interface
** execute rc.init.sh
Serial Number = 
Serial Number = 
Segmentation fault
1.Set Date & time ...(command: sntp -r ntp1.dlink.com &)
get IP = [NONE SET]
sntp: unable to locate IP address/number
sntp: Success
<rtc>: getRTC time= 7/7/15 22:56:17
check button V2.19.03292007
1.03(1.03.0330.2007)
03/30/2007
SIOCADDRT: No such device
mfg_search
create /tmp/fatmount script file
mount FAT storage devices
Jul 15 22:56:17 crond[515]: crond 2.3.2 dillon, started, log level 8


mount: /dev/sda is not a valid block device
mount: /dev/sdb is not a valid block device
mount: /dev/sdc is not a valid block device
kill: Usage: kill [-s sigspec | -signum | -sigspec] [pid | job]... or
kill -l [exitstatus]
** Get MAC Addr

UPnP AV / MediaServer v1.02.0317.2006.

sendto-a mount: /dev/sda1 is not a valid block device
UPNPAV_MGR: Generate key failed.
UPNPMGR: Get ShareFolder=/mnt.
upnpav_path=/mnt
Have not diskA
Have not diskB
mount: /dev/sdb1 is not a valid block device
Quota Stop
Link Layer Topology Discovery Protocol, version 1.05.1223.2005

dev is  <NULL>

548: Segmentation fault
mount: /dev/sdc1 is not a valid block device
<fancontrol>Current speed(6467) Set speed(2700), Not the same
op_server 0 0 0 &

Starting pid 596, console /dev/ttyS0: '/bin/sh'


BusyBox v1.00-pre1 (2006.07.17-10:17+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.

Offline

 

#2 2007-07-17 01:00:52

KRH
Member
From: Denmark
Registered: 2006-10-27
Posts: 219
Website

Re: How to recover or update firmware, manually w/o webinterface ???

i have compiled the webserver to be run form /mnt/HD_a2/web if you can download and extract that one
http://upit.jtw.dk/dl/uwn/

First user to fun_plug the dns-323.

Offline

 

#3 2007-07-19 00:43:34

Tester
Member
Registered: 2007-02-23
Posts: 23

Re: How to recover or update firmware, manually w/o webinterface ???

Thanks for your try.

Seems that the image in the Flash is damaged, D-Link tried to help with resets but didn't change any.

I got an RMA and have to send it back to get a new one.

Offline

 

 

Pages: 1

Board footer

Powered by PunBB
© Copyright 2002–2010 PunBB