DSM-G600, DNS-3xx and NSA-220 Hack Forum

Hi,

I am trying to mount a drive via the USB port.  The drive is recognized but in the log are some error message (Bad LUN, Bad target number).  Also, when I attempt to mount the drive it fails with the message mount: mounting /dev/sdc on /mnt/ext failed

Here are the entries in the log

SCSI device sdc: 1465149168 512-byte hdwr sectors (750156 MB)
sdc: assuming drive cache: write through
sdc:<7>usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage:  28 00 00 00 00 00 00 00 08 00
usb-storage: Bulk Command S 0x43425355 T 0x6 L 4096 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 4096 bytes, 1 entries
usb-storage: Status code 0; transferred 4096/4096
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes
usb-storage: Status code 0; transferred 13/13
usb-storage: -- transfer complete
usb-storage: Bulk status result = 0
usb-storage: Bulk Status S 0x53425355 T 0x6 R 0 Stat 0x0
usb-storage: scsi cmd done, result=0x0
usb-storage: *** thread sleeping.
sdc1
Attached scsi disk sdc at scsi6, channel 0, id 0, lun 0
Attached scsi generic sg2 at scsi6, channel 0, id 0, lun 0,  type 0
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad LUN (0:1)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (1:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (2:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (3:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (4:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (5:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (6:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Bad target number (7:0)
usb-storage: scsi cmd done, result=0x40000
usb-storage: *** thread sleeping.
usb-storage: device scan complete
usb-storage: queuecommand called
usb-storage: *** thread awakened.
usb-storage: Command READ_10 (10 bytes)
usb-storage:  28 00 00 00 00 00 00 00 01 00
usb-storage: Bulk Command S 0x43425355 T 0xf L 512 F 128 Trg 0 LUN 0 CL 10
usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes
usb-storage: Status code 0; transferred 31/31
usb-storage: -- transfer complete
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_bulk_transfer_sglist: xfer 512 bytes, 1 entries
usb-storage: Status code 0; transferred 512/512
usb-storage: -- transfer complete
usb-storage: Bulk data transfer result 0x0
usb-storage: Attempting to get CSW...
...

Any thoughts?

Last edited by jboy (2007-09-22 18:42:18)