DSM-G600, DNS-3xx and NSA-220 Hack Forum

Credo · 2009-06-10 20:30:17

Hello,

I'm wondering if there's any documentation, or steps to follow in order to put the DNS-323 back to it's original (retail) state. Removing Fun plug and all that so It's JUST the dlink software? Right now the administration site is on port 81, I'd like to move everything back to the way it was prior to the Fun Plug install. As of now, I'm running Firmware 1.08 (which btw is running quite nicely).

...Soon after, I would like to re install fun plug, but want to Clean up the device back to factory settings first.

Any help would be greatly appreciated!
Thanks very much in advance!

~C.

Credo · 2009-06-10 23:44:21

...bump....

anyone know what to do here? I basically have no access to the command. the root account doesn't work anymore..

mig · 2009-06-11 02:24:47

Have you tried pressing the reset button on the back of the DNS-323? (Hold for 3 -5 seconds)

Last edited by mig (2009-06-11 02:25:12)

Credo · 2009-06-11 02:40:42

That doesn't wipe everything. and put it back to its original state prior to the FUN plug installation.

luusac · 2009-06-11 04:54:53

to do the uninstall part of your reset you will need to delete fun_plug in the root of your drive as well as the /ffp directory. If you don't have console access you may find this difficult as some files are owned by root, so you won't have permissions to delete them. You can just install telnet and remove the /ffp directory from there. See the wiki how to on telnet for instructions on how to install a 'standalone' telnet.

mig · 2009-06-11 08:37:00

Credo wrote:
That doesn't wipe everything. and put it back to its original state prior to the FUN plug installation.

Well, that's a big word 'everything'.

If you want to wipe 'everything' press the reset button and re-partition your drives.

What exactly are you still trying to remove after the reset button press?

Last edited by mig (2009-06-11 08:38:47)

Credo · 2009-06-11 15:11:38

I'm trying to get rid of everything related to the Fun Plug application. I want the unit itself to be in the same condition it was in when it was pulled out of the box.

The luusac I think gave all the instruction I needed.

Thanks very much though.

luusac · 2009-06-11 18:28:20

to get the unit to the out of box state you not only need to clear whatever you have put on the hdds (i.e. /ffp /ipkg (optware if you have it) etc also need to clear configuration details and serial numbers in nvram - I think the reset via the webgui or the pinhole while booting should do that, this is because the unit stores config data and drive serial info in nvram. ffp etc store their config on the hdds

mig · 2009-06-11 22:14:53

luusac wrote:
ffp etc store their config on the hdds

Additionally there are some ffp scripts which modify the NVRAM, such as store-passwd.sh.

Credo, did you run this script from your ffp installation?
I bring this up, because I see you have another thread about a root login issue.

Last edited by mig (2009-06-11 22:18:10)

DSM-G600, DNS-3xx and NSA-220 Hack Forum

Announcement

#1 2009-06-10 20:30:17

Reverting back to original state...

#2 2009-06-10 23:44:21

Re: Reverting back to original state...

#3 2009-06-11 02:24:47

Re: Reverting back to original state...

#4 2009-06-11 02:40:42

Re: Reverting back to original state...

#5 2009-06-11 04:54:53

Re: Reverting back to original state...

#6 2009-06-11 08:37:00

Re: Reverting back to original state...

Credo wrote:

#7 2009-06-11 15:11:38

Re: Reverting back to original state...

#8 2009-06-11 18:28:20

Re: Reverting back to original state...

#9 2009-06-11 22:14:53

Re: Reverting back to original state...

luusac wrote:

Board footer