DSM-G600, DNS-3xx and NSA-220 Hack Forum
Unfortunately no one can be told what fun_plug is - you have to see it for yourself.
You are not logged in.
Announcement
IRC Channel #funplug on irc.freenode.org
#1 2012-07-09 22:38:46
- davegsm82
- New member
- Registered: 2012-07-09
- Posts: 4
DNS323 Not booting, error message.
I've recently bought a DNS323, it won't boot and plugging into the Serial port gave the following;
OK
** LOADER **
** MARVELL BOARD: RD-88F5182-NAS-2 LE
U-Boot 1.1.1 (Feb 26 2009 - 11:33:03) Marvell version: 1.7.3.003
DRAM CS[0] base 0x00000000 size 64MB
DRAM Total size 64MB
Detect phy 1111
[8192kB@ff800000] Flash: 8 MB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
*** Warning - bad CRC, using default environment
Soc: MV88F5182 Rev 2
CPU: ARM926 (Rev 0) running @ 500Mhz
SysClock = 166Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Hit any key to stop autoboot: 0
## Booting image at ff820000 ...
Image Name: Linux-2.6.12.6-arm1
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1490204 Bytes = 1.4 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at ff9a0000 ...
Image Name: Ramdisk
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5507627 Bytes = 5.3 MB
Load Address: 00800000
Entry Point: 00800000
Verifying Checksum ... Bad Data CRC
After the Bad CRC message, it reboots and starts over again.
I tried flashing the original firmware back into it using the guide online (Kermit upload via terraterm) but its the same.
I recon its probably a bad Flash IC, as you get an error when flashing the firmware saying it 'can't delete block' maybe 10-15 times but the flash operation completes without crashing out.
If it is a Bad IC, I can change it, I have Surface mount rework equipment, does anyone have any scrap boards laying about that I could rob bits from?
Cheers, Dave.
Offline
#2 2012-07-11 01:05:33
- davegsm82
- New member
- Registered: 2012-07-09
- Posts: 4
Re: DNS323 Not booting, error message.
Anyone? Any advice?
Offline
#3 2012-07-11 18:11:07
- bjby
- Member
- Registered: 2009-02-22
- Posts: 265
Re: DNS323 Not booting, error message.
I got something similiar. For me it wasnt possible to upload the orignal firmware it was too large.
Does it work using the debian installer (which is far smaller)?
more info here http://dns323.kood.org/forum/viewtopic.php?id=4656
Last edited by bjby (2012-07-11 18:13:37)
Offline
#4 2012-07-16 01:29:27
- davegsm82
- New member
- Registered: 2012-07-09
- Posts: 4
Re: DNS323 Not booting, error message.
Hi bjby,
I've not tried it with the debian installer, to be honest i'm a bit of a noob where anything linux is concerned so I don't know where to start at the minute.
Tonight just for fun I tried uploading the oldest image I could find which is 1.03, from the D-link website, dong so showed that its definitely a flash related issue.
Marvell>> loadb k
## Ready for binary (kermit) download to 0x00100000 at 115200 bps...
## Total Size = 0x0015c3b7 = 1426359 Bytes
## Start Addr = 0x00100000
Un-Protect Flash Bank # 1
Erase Kernel from 0xff820000 to 0xff99ffff Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Can't erase unknown flash type - aborted
Erased 1 sectors
Kernel Size = 1426359
Copy to Flash... done
Protect Flash Bank # 1
Marvell>>
Any clues? Is there a guide to installing using debian?
Cheers, Dave.
Offline
#5 2012-07-16 10:02:40
#6 2012-09-30 10:02:25
- Homelab
- Member
- Registered: 2011-12-21
- Posts: 8
Re: DNS323 Not booting, error message.
Hi! I'm sorry, I do not know English. (= Google Translate)
I have a DNS-323-B1, which gives the following message:
** MARVELL BOARD: RD-88F5182-NAS-2 LE
U-Boot 1.1.1 (Nov 27 2006 - 14:25:52) Marvell version: 1.7.3
DRAM CS[0] base 0x00000000 size 64MB
DRAM Total size 64MB
[8192kB@ff800000] Flash: 8 MB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
*** Warning - bad CRC, using default environment
Soc: MV88F5182 Rev 2
CPU: ARM926 (Rev 0) running @ 500Mhz
SysClock = 166Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Hit any key to stop autoboot: 0
## Booting image at ff820000 ...
Bad Magic Number
Marvell>> <INTERRUPT>
Marvell>>
The loadb k, send uKernel not work because the Kermit "Fatal Kermit Protocol Error: Too many retries" message stops. / parameters for flow control, parity etc. is set to /
Does anyone have any ideas?
Please Step by Step....
Or trash it? ...
Offline