DSM-G600, DNS-3xx and NSA-220 Hack Forum

Unfortunately no one can be told what fun_plug is - you have to see it for yourself.

You are not logged in.

#1 2015-07-28 19:38:29

gasman
Member
From: Swansea,UK
Registered: 2009-06-23
Posts: 94

Need to reset DNS323

Hi, Guys,

It has been quite a while since I have been on here. My first DNS323 is still going strong, but my backup second DNS323 is now playing up and looking for some advice.

Both have f/w version 1.08. I've not really touched them for ages. the second has been off for more than a year. I was using it only to back up my initial DNS323. Both are/were set as raid 1.

This weekend I decided to rsync my data from DNS1 to DNS2. DNS1 has 2 500GB drives, DNS2 has 2 2TB drives.

I did receive a message disk full from DNS2, and that is probably because I rync'd to the wrong folder.

I tried to shut the DNS2 down, with the switch on the front, but it would not shutdown. I'd killed the rsync processes on DNS2 before trying this.

I can still telnet into DNS2, but cannot access from windows. Win7 sees DNS2 but the diagnostic says refused connection.

As this is just a backup, I decided that I would rebuid the array and format the disks, but get error Hard Drive(s) Formatting Failure. (Error Code:107). and the data remains intact.

I am not that conversant with Linux, but am happy with command line options if given exactly what to do.

So now I am either trying to start all over as if I have just bought a new unit with new disks, or correct what is there and remove errant files.

I have fun plug on both units, but is has been ages since I installed it.

Can someone please supply some ideas on how to get the DNS2 unit back up and running. The unit is at fault as I tested mapping the unit from another computer and got the 'network path cannot be found'

DNS2 unit has blue network light but pink disk lights. Both 2TB disks are recognised in the GUI.


TIA


DNS-323 FW 1.08 (05/15/2009) HW:B1
2 * Seagate    ST3500630AS (500GB)  Fun_plug 0.5
DNS-323 FW 1.08  (12/18/2009) HW:B1
2 * Hitachi    HDS5C3020ALA632 (2TB)  Fun_plug 0.5

Offline

 

#2 2015-07-28 22:11:38

Mijzelf
Member / Developer
Registered: 2008-07-05
Posts: 709

Re: Need to reset DNS323

You can login and run

Code:

df
cat /proc/mounts
cat /proc/mdstat
dmesg

The first command will show the usage of all devices. The second the mounts, the 3th the status of the raid array, and the 4th the kernel logs.

Offline

 

#3 2015-07-29 11:49:45

gasman
Member
From: Swansea,UK
Registered: 2009-06-23
Posts: 94

Re: Need to reset DNS323

Thank you Mijzelf,

Here are the results of those commands. Can you see anything that stands out as causing the problem.?

TIA


df

Code:

Filesystem           1k-blocks      Used Available Use% Mounted on
rootfs                    9911      8866       533  94% /
/dev/root                 9911      8866       533  94% /
/dev/loop0                5760      5760         0 100% /sys/crfs
/dev/md0             1920786672 223133188 1697653484  12% /mnt/HD_a2
/dev/sda4               497861      2720    495141   1% /mnt/HD_a4
/dev/sdb4               497861      2326    495535   0% /mnt/HD_b4

cat /proc/mounts

Code:

rootfs / rootfs rw 0 0
/dev/root / ext2 rw 0 0
proc /proc proc rw,nodiratime 0 0
/dev/loop0 /sys/crfs squashfs ro 0 0
/dev/md0 /mnt/HD_a2 ext2 rw 0 0
/dev/sda4 /mnt/HD_a4 ext2 rw 0 0
/dev/sdb4 /mnt/HD_b4 ext2 rw 0 0
none /proc/bus/usb usbfs rw 0 0
devpts /dev/pts devpts rw 0 0

cat /proc/mdstat

Code:

Personalities : [linear] [raid0] [raid1]
md0 : active raid1 sda2[0] sdb2[1]
      1951407424 blocks [2/2] [UU]

unused devices: <none>

dmesg

Code:

Linux version 2.6.12.6-arm1 (tim@SWTEST2) (gcc version 3.3.3) #32 Wed Jun 24 15:
19:48 CST 2009
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 166000000, Tclk = 166000000
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 16384
  DMA zone: 16384 pages, LIFO batch:7
  Normal zone: 0 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=/dev/ram console=ttyS0,115200 :::DB88FXX81:egiga0:none
PID hash table entries: 512 (order: 9, 8192 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB 0MB 0MB 0MB = 64MB total
Memory: 55296KB available (2596K code, 463K data, 112K init)
Calibrating delay loop... 331.77 BogoMIPS (lpj=1658880)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 6323K
NET: Registered protocol family 16

  Marvell Development Board (LSP Version 1.7.6_NAS)-- RD-88F5182-NAS-2

 Detected Tclk 166000000 and SysClk 166000000
Marvell USB EHCI Host controller #0: c0e49a40
Marvell USB EHCI Host controller #1: c0e49bc0
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
cesadev_init(c0012498)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
inotify device minor=63
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.3 (2007/10/31) Phillip Lougher
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Initializing Cryptographic API
Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
io scheduler noop registered
io scheduler deadline registered
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
  o Ethernet descriptors in DRAM
  o DRAM SW cache-coherency
  o Checksum offload enabled
  o Loading network interface 'egiga0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
  Vendor: Hitachi   Model: HDS5C3020ALA632   Rev: ML6O
  Type:   Direct-Access                      ANSI SCSI revision: 03
  Vendor: Hitachi   Model: HDS5C3020ALA632   Rev: ML6O
  Type:   Direct-Access                      ANSI SCSI revision: 03
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0,  type 0
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0,  type 0
physmap flash device: 800000 at ff800000
phys_mapped_flash: Found 1 x16 devices at 0x0 in 8-bit bank
 Amd/Fujitsu Extended Query Table at 0x0040
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
Using physmap partition definition
Creating 5 MTD partitions on "phys_mapped_flash":
0x00000000-0x00010000 : "MTD1"
0x00010000-0x00020000 : "MTD2"
0x00020000-0x001a0000 : "Linux Kernel"
0x001a0000-0x007d0000 : "File System"
0x007d0000-0x00800000 : "u-boot"
ehci_platform ehci_platform.20865: EHCI Host Controller
ehci_platform ehci_platform.20865: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.20865: irq 17, io mem 0x00000000
ehci_platform ehci_platform.20865: park 0
ehci_platform ehci_platform.20865: USB 0.0 initialized, EHCI 1.00, driver 10 Dec
 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.86401: EHCI Host Controller
ehci_platform ehci_platform.86401: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.86401: irq 12, io mem 0x00000000
ehci_platform ehci_platform.86401: park 0
ehci_platform ehci_platform.86401: USB 0.0 initialized, EHCI 1.00, driver 10 Dec
 2004
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
mice: PS/2 mouse device common for all mice
md: linear personality registered as nr 1
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 112K
SCSI device sda: 3907029168 512-byte hdwr sectors (2000399 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 3907029168 512-byte hdwr sectors (2000399 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda4
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sdb: 3907029168 512-byte hdwr sectors (2000399 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 3907029168 512-byte hdwr sectors (2000399 MB)
SCSI device sdb: drive cache: write back
 sdb: sdb1 sdb2 sdb4
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
egiga0: mac address changed
egiga0: link down
Adding 530104k swap on /dev/sda1.  Priority:-1 extents:1
Adding 530104k swap on /dev/sdb1.  Priority:-2 extents:1
egiga0: link up<5>, full duplex<5>, speed 1 Gbps<5>
ext3: No journal on filesystem on sda4
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
ext3: No journal on filesystem on sdb4
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
ext3: No journal on filesystem on sda2
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
ext3: No journal on filesystem on sdb2
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
md: md0 stopped.
md: md1 stopped.
md: md0 stopped.
md: bind<sdb2>
md: bind<sda2>
raid1: raid set md0 active with 2 out of 2 mirrors
ext3: No journal on filesystem on md0
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
ext3: No journal on filesystem on sda4
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
ext3: No journal on filesystem on sdb4
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
md: mdadm(pid 1737) used obsolete MD ioctl, upgrade your software to use new ict
ls.
usbcore: deregistering driver usblp

DNS-323 FW 1.08 (05/15/2009) HW:B1
2 * Seagate    ST3500630AS (500GB)  Fun_plug 0.5
DNS-323 FW 1.08  (12/18/2009) HW:B1
2 * Hitachi    HDS5C3020ALA632 (2TB)  Fun_plug 0.5

Offline

 

#4 2015-07-29 12:58:52

gasman
Member
From: Swansea,UK
Registered: 2009-06-23
Posts: 94

Re: Need to reset DNS323

I believe the smb is screwed somehow.?

I booted another PC with a Knoppix CD and again was able to see the device, but unable to see the shares on it.

I have simply allowed All to access Volume_1 via the GUI and then added myself as a test

Code:

[ Volume_1 ]
comment =
path = /mnt/HD_a2
valid users =
read only = no
guest ok = yes
oplocks = no
map archive = no

[ Volume_1-1 ]
comment =
path = /mnt/HD_a2
valid users = paul
read only = no
guest ok = no
oplocks = no
map archive = no

DNS-323 FW 1.08 (05/15/2009) HW:B1
2 * Seagate    ST3500630AS (500GB)  Fun_plug 0.5
DNS-323 FW 1.08  (12/18/2009) HW:B1
2 * Hitachi    HDS5C3020ALA632 (2TB)  Fun_plug 0.5

Offline

 

#5 2015-07-29 13:19:44

gasman
Member
From: Swansea,UK
Registered: 2009-06-23
Posts: 94

Re: Need to reset DNS323

Ok,

From this link http://forums.dlink.com/index.php?topic=19844.0 I discovered 'showmount -e'

On my working unit it shows

Code:

Export list for DLINK323:
/mnt/HD_a2/Music 192.168.2.0/24
/mnt/HD_a4       192.168.2.0/24
/mnt/HD_b4       192.168.2.0/24
/mnt/web_page    192.168.2.0/24

on the non working unit it shows absolutely nothing.

I've attached the GUI to show they should be mapped.


Attachments:
Attachment Icon dns323a.png, Size: 147,005 bytes, Downloads: 159

DNS-323 FW 1.08 (05/15/2009) HW:B1
2 * Seagate    ST3500630AS (500GB)  Fun_plug 0.5
DNS-323 FW 1.08  (12/18/2009) HW:B1
2 * Hitachi    HDS5C3020ALA632 (2TB)  Fun_plug 0.5

Offline

 

#6 2015-07-29 13:36:14

Mijzelf
Member / Developer
Registered: 2008-07-05
Posts: 709

Re: Need to reset DNS323

When there is something wrong with the filesystem of your nas, the kernel is not aware of it. Your postings look fine.

When it's only samba, you should restart it. Unfortunately I don't know how to do that on a 323. Maybe

Code:

/etc/init.d/samba restart

BTW, have you already rebooted that nas?

Offline

 

#7 2015-07-29 14:44:16

gasman
Member
From: Swansea,UK
Registered: 2009-06-23
Posts: 94

Re: Need to reset DNS323

I have been searching all morning and must admit I'd forgotten about the hard reset on the back of the unit, which I have just this minute done.

I now have to remember what I next need to do to get it back up an running as I have now lost the static ip address.

I had rebooted the unit several times yesterday.

Even investigating Alt-F which I have found while looking for solutions.


DNS-323 FW 1.08 (05/15/2009) HW:B1
2 * Seagate    ST3500630AS (500GB)  Fun_plug 0.5
DNS-323 FW 1.08  (12/18/2009) HW:B1
2 * Hitachi    HDS5C3020ALA632 (2TB)  Fun_plug 0.5

Offline

 

#8 2015-07-29 16:20:32

gasman
Member
From: Swansea,UK
Registered: 2009-06-23
Posts: 94

Re: Need to reset DNS323

Windows diagnostic does not help much

'The device or resource (DLINK323A) is not set up to accept connections on port "The File and printer sharing (SMB'

I've hard booted and reset ip address etc.

There is something definitely wrong with the setup. One minute the SMB list is there with Volume_1, and then it disappears. If I restart, it appears again.

Power button is also pink.?

I was hoping to use this experience in case my main DNS323 went this way, but have not learnt much at present. sad

If you have no idea as what to try next, I'll give that Alt-F f/w a go.?


DNS-323 FW 1.08 (05/15/2009) HW:B1
2 * Seagate    ST3500630AS (500GB)  Fun_plug 0.5
DNS-323 FW 1.08  (12/18/2009) HW:B1
2 * Hitachi    HDS5C3020ALA632 (2TB)  Fun_plug 0.5

Offline

 

#9 2015-07-29 18:53:55

Mijzelf
Member / Developer
Registered: 2008-07-05
Posts: 709

Re: Need to reset DNS323

One minute the SMB list is there with Volume_1, and then it disappears. If I restart, it appears again.

So it seems samba crashes. You can see that by executing

Code:

netstat -ltp

It shows all listening daemons, including the ports they have open. I think smbd should have 2 ports open. If there is no smbd running, maybe you can find out why it crashes by executing it manually, without daemonizing.

Code:

smbd -F -d 3 -s /etc/samba/smb.conf

Here '3' is a debug level, and you have to check if your configuration file is indeed on that place,

Offline

 

#10 2015-07-29 20:34:39

gasman
Member
From: Swansea,UK
Registered: 2009-06-23
Posts: 94

Re: Need to reset DNS323

Thank you Mijzelf,

I've switched it off for the night now, but will look at it again first thing in the morning.

My smb.conf is in that location.

Thanks again for all these commands to try the various options.


DNS-323 FW 1.08 (05/15/2009) HW:B1
2 * Seagate    ST3500630AS (500GB)  Fun_plug 0.5
DNS-323 FW 1.08  (12/18/2009) HW:B1
2 * Hitachi    HDS5C3020ALA632 (2TB)  Fun_plug 0.5

Offline

 

#11 2015-07-30 10:53:35

gasman
Member
From: Swansea,UK
Registered: 2009-06-23
Posts: 94

Re: Need to reset DNS323

Results of netstat -lpt

Code:

Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address           Foreign Address         State
PID/Program name
tcp        0      0 localhost.localdomain:9000 0.0.0.0:*               LISTEN
   1963/twonkymediaser
tcp        0      0 DLINK323A:9000          0.0.0.0:*               LISTEN
1963/twonkymediaser
tcp        0      0 0.0.0.0:http            0.0.0.0:*               LISTEN
1593/webs
tcp        0      0 0.0.0.0:22              0.0.0.0:*               LISTEN
1955/sshd
tcp        0      0 0.0.0.0:telnet          0.0.0.0:*               LISTEN
1940/telnetd

smbd -F -d 3 -s /etc/samba/smb.conf produces nothing

ps shows

Code:

PID   USER     COMMAND
    1 0        init
    2 0        [ksoftirqd/0]
    3 0        [events/0]
    4 0        [khelper]
    5 0        [kthread]
   11 0        [kblockd/0]
   14 0        [khubd]
   49 0        [pdflush]
   50 0        [pdflush]
   52 0        [aio/0]
  189 0        [scsi_eh_0]
   51 0        [kswapd0]
  190 0        [scsi_eh_1]
  200 0        [mtdblockd]
  217 0        [kcryptd/0]
  218 0        [kmirrord/0]
  229 0        [loop0]
 1329 0        xmldb -n config
 1372 0        [md0_raid1]
 1564 0        chkbutton
 1593 0        /web/webs
 1631 0        fancontrol 0
 1639 0        op_server 3 3 3
 1646 0        -sh
 1676 0        check_daemon
 1685 0        crond
 1826 0        mserver
 1940 0        /ffp/sbin/telnetd -l /ffp/bin/sh
 1955 0        /ffp/sbin/sshd
 1962 0        /mnt/HD_a2/twonky/twonkymedia
 1963 0        /mnt/HD_a2/twonky/twonkymediaserver
 1964 0        /mnt/HD_a2/twonky/twonkymediaserver
 1965 0        /mnt/HD_a2/twonky/twonkymediaserver
 1966 0        /mnt/HD_a2/twonky/twonkymediaserver
 1967 0        /mnt/HD_a2/twonky/twonkymediaserver
 1968 0        /mnt/HD_a2/twonky/twonkymediaserver
 1969 0        /mnt/HD_a2/twonky/twonkymediaserver
 1970 0        /mnt/HD_a2/twonky/twonkymediaserver
 1971 0        /mnt/HD_a2/twonky/twonkymediaserver
 1973 0        /mnt/HD_a2/twonky/twonkymediaserver
 1974 0        /mnt/HD_a2/twonky/twonkymediaserver
 1975 0        /mnt/HD_a2/twonky/twonkymediaserver
 1977 0        /mnt/HD_a2/twonky/twonkymediaserver
 1978 0        /mnt/HD_a2/twonky/twonkymediaserver
 1983 0        /mnt/HD_a2/twonky/twonkymediaserver
 1984 0        /mnt/HD_a2/twonky/twonkymediaserver
 1985 0        /mnt/HD_a2/twonky/twonkymediaserver
 2198 0        /mnt/HD_a2/twonky/twonkymediaserver
 2929 0        /ffp/bin/sh
 3141 0        ps

Logging into the GUI shows

Code:

Share     Path    User/Group    Comment    Oplocks    Map archive    R/W        
Volume_1    Volume_1    ALL         No    No

I tried smb start and received
$Starting SMB services:
$Starting NMB services:

but ps only shows
3411 0        /usr/sbin/samba/nmbd -D

as an extra process?

Here is the netstat from my working NAS

Code:

Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address           Foreign Address         State
PID/Program name
tcp        0      0 0.0.0.0:2049            0.0.0.0:*               LISTEN
1950/unfsd
tcp        0      0 0.0.0.0:515             0.0.0.0:*               LISTEN
1790/lpd Waiting
tcp        0      0 0.0.0.0:5000            0.0.0.0:*               LISTEN
2020/rsync
tcp        0      0 localhost.localdomain:9000 0.0.0.0:*               LISTEN
   1976/twonkymediaser
tcp        0      0 DLINK323:9000           0.0.0.0:*               LISTEN
1976/twonkymediaser
tcp        0      0 localhost.localdomain:9001 0.0.0.0:*               LISTEN
   2143/twonkymediaser
tcp        0      0 DLINK323:9001           0.0.0.0:*               LISTEN
2143/twonkymediaser
tcp        0      0 0.0.0.0:139             0.0.0.0:*               LISTEN
2131/smbd
tcp        0      0 0.0.0.0:111             0.0.0.0:*               LISTEN
1940/rpc.portmap
tcp        0      0 0.0.0.0:http            0.0.0.0:*               LISTEN
1557/webs
tcp        0      0 0.0.0.0:ftp             0.0.0.0:*               LISTEN
1726/pure-ftpd (SER
tcp        0      0 0.0.0.0:22              0.0.0.0:*               LISTEN
2009/sshd
tcp        0      0 0.0.0.0:telnet          0.0.0.0:*               LISTEN
1961/telnetd
tcp        0      0 0.0.0.0:443             0.0.0.0:*               LISTEN
1557/webs
tcp        0      0 0.0.0.0:445             0.0.0.0:*               LISTEN
2131/smbd

DNS-323 FW 1.08 (05/15/2009) HW:B1
2 * Seagate    ST3500630AS (500GB)  Fun_plug 0.5
DNS-323 FW 1.08  (12/18/2009) HW:B1
2 * Hitachi    HDS5C3020ALA632 (2TB)  Fun_plug 0.5

Offline

 

#12 2015-07-30 12:16:02

gasman
Member
From: Swansea,UK
Registered: 2009-06-23
Posts: 94

Re: Need to reset DNS323

I have 4 processes running for samba on my working NAS, but notice on the previous post for the non working NAS that the user is 0?

working NAS

Code:

PID   USER     COMMAND
    1 root     init
    2 root     [ksoftirqd/0]
    3 root     [events/0]
    4 root     [khelper]
    5 root     [kthread]
   11 root     [kblockd/0]
   14 root     [khubd]
   49 root     [pdflush]
   50 root     [pdflush]
   52 root     [aio/0]
   51 root     [kswapd0]
  189 root     [scsi_eh_0]
  190 root     [scsi_eh_1]
  200 root     [mtdblockd]
  217 root     [kcryptd/0]
  218 root     [kmirrord/0]
  233 root     [loop0]
 1266 root     atd
 1302 root     xmldb -n config
 1345 root     [md0_raid1]
 1533 root     chkbutton
 1557 root     /web/webs
 1663 root     check_hotplug
 1668 root     check_daemon
 1678 root     crond
 1726 root     pure-ftpd (SERVER)
 1774 root     op_server 0 0 0
 1785 root     -sh
 1790 root     lpd Waiting
 1832 root     mserver
 1833 root     apkg
 1940 root     /ffp/sbin/rpc.portmap
 1950 root     /ffp/sbin/unfsd -e /ffp/etc/exports
 1961 root     /ffp/sbin/telnetd -l /ffp/bin/sh
 1975 root     /mnt/HD_a2/twonky/twonkymedia -powersavemode 1
 1976 root     /mnt/HD_a2/twonky/twonkymediaserver -powersavemode 1
 1977 root     /mnt/HD_a2/twonky/twonkymediaserver -powersavemode 1
 1978 root     /mnt/HD_a2/twonky/twonkymediaserver -powersavemode 1
 1979 root     /mnt/HD_a2/twonky/twonkymediaserver -powersavemode 1
 1980 root     /mnt/HD_a2/twonky/twonkymediaserver -powersavemode 1
 1981 root     /mnt/HD_a2/twonky/twonkymediaserver -powersavemode 1
 1982 root     /mnt/HD_a2/twonky/twonkymediaserver -powersavemode 1
 1983 root     /mnt/HD_a2/twonky/twonkymediaserver -powersavemode 1
 2009 root     /ffp/sbin/sshd
 2020 root     /ffp/bin/rsync --daemon --config=/ffp/etc/rsyncd.conf
 2023 root     /ffp/sbin/fanctl /ffp/etc/fanctl.conf
 2026 root     /ffp/sbin/fanctl /ffp/etc/fanctl.conf
 2059 root     [scsi_eh_2]
 2060 root     [usb-storage]
 2131 root     /usr/sbin/samba/smbd -D
 2135 root     /usr/sbin/samba/smbd -D
 2136 root     /usr/sbin/samba/nmbd -D
 2142 root     /mnt/HD_a2/twonky/twonkymedia
 2143 root     /mnt/HD_a2/twonky/twonkymediaserver
 2144 root     /mnt/HD_a2/twonky/twonkymediaserver
 2145 root     /mnt/HD_a2/twonky/twonkymediaserver
 2146 root     /mnt/HD_a2/twonky/twonkymediaserver
 2147 root     /mnt/HD_a2/twonky/twonkymediaserver
 2148 root     /mnt/HD_a2/twonky/twonkymediaserver
 2149 root     /mnt/HD_a2/twonky/twonkymediaserver
 2151 root     /mnt/HD_a2/twonky/twonkymediaserver
 9835 nobody   /usr/sbin/samba/smbd -D
10381 root     /ffp/bin/sh
15340 root     ps

DNS-323 FW 1.08 (05/15/2009) HW:B1
2 * Seagate    ST3500630AS (500GB)  Fun_plug 0.5
DNS-323 FW 1.08  (12/18/2009) HW:B1
2 * Hitachi    HDS5C3020ALA632 (2TB)  Fun_plug 0.5

Offline

 

#13 2015-07-30 14:21:16

gasman
Member
From: Swansea,UK
Registered: 2009-06-23
Posts: 94

Re: Need to reset DNS323

Have reloaded FW 1.08 hoping that would clear stuff out. When I do that for my VOIP box I have to re enter all the settings, but no improvement.

Right now I would just like to get it back to brand new in the box and start from scratch. The GUI does not appear to apply all the settings I apply.


DNS-323 FW 1.08 (05/15/2009) HW:B1
2 * Seagate    ST3500630AS (500GB)  Fun_plug 0.5
DNS-323 FW 1.08  (12/18/2009) HW:B1
2 * Hitachi    HDS5C3020ALA632 (2TB)  Fun_plug 0.5

Offline

 

#14 2015-07-30 16:25:57

gasman
Member
From: Swansea,UK
Registered: 2009-06-23
Posts: 94

Re: Need to reset DNS323

Well a Factory Reset has now got me access via windows.

ps now shows

Code:

PID   USER     COMMAND
    1 root     init
    2 root     [ksoftirqd/0]
    3 root     [events/0]
    4 root     [khelper]
    5 root     [kthread]
   11 root     [kblockd/0]
   14 root     [khubd]
   49 root     [pdflush]
   50 root     [pdflush]
   52 root     [aio/0]
  189 root     [scsi_eh_0]
   51 root     [kswapd0]
  190 root     [scsi_eh_1]
  200 root     [mtdblockd]
  217 root     [kcryptd/0]
  218 root     [kmirrord/0]
  229 root     [loop0]
 1757 root     xmldb -n config
 1800 root     [md0_raid1]
 1992 root     chkbutton
 2027 root     /web/webs
 2047 root     fancontrol 0
 2059 root     op_server 3 3 3
 2065 root     -sh
 2100 root     check_hotplug
 2105 root     check_daemon
 2200 root     lpd Waiting
 2234 root     mserver
 2235 root     apkg
 2365 root     /ffp/sbin/telnetd -l /ffp/bin/sh
 2380 root     /ffp/sbin/sshd
 2700 root     /usr/sbin/samba/smbd -D
 2704 root     /usr/sbin/samba/nmbd -D
 2708 root     /usr/sbin/samba/smbd -D
 2751 root     atd
 2766 root     crond
 2891 root     /ffp/bin/sh
 2946 root     /usr/sbin/samba/smbd -D
 3040 root     ps

and all data is intact. Phew big_smile

Many thanks for all your help.

Last edited by gasman (2015-07-30 16:26:17)


DNS-323 FW 1.08 (05/15/2009) HW:B1
2 * Seagate    ST3500630AS (500GB)  Fun_plug 0.5
DNS-323 FW 1.08  (12/18/2009) HW:B1
2 * Hitachi    HDS5C3020ALA632 (2TB)  Fun_plug 0.5

Offline

 

Board footer

Powered by PunBB
© Copyright 2002–2010 PunBB