Differences

This shows you the differences between the selected revision and the current version of the page.

hardware:jtag 2008/03/10 23:55 hardware:jtag 2017/09/06 18:38 current
Line 13: Line 13:
  * You need a JTAG cable   * You need a JTAG cable
-===== JTAG Interface scheme for DNS-323 =====+Two types of jtag cables are discussed here: 
 +1: The "Wiggler" style, which is basically a conversion between the jtag interface on the embedded system and the parralel (printer) port on your PC.  
 +2: The "Amontec JTAGKey Tiny" (other commercially models may or may not work), which provides a USB connection at the PC side. 
 +Comparison: pro method 1: cheaper, Pro method 2: less soldering (faster?)
-{{hardware:dns-323-jtag.pdf| JTAG Port Pinout and Wiggler style Programmer}} 
===== JTAG Pinout Reference ===== ===== JTAG Pinout Reference =====
Line 30: Line 32:
**Note nTRST must be sent a buffered high signal to use JTAG** **Note nTRST must be sent a buffered high signal to use JTAG**
 +Be aware that this pinout seems to be based on the DNS 323 version B2 and the CH3SNAS. The DNS-323 version A1 has the same space for a header, but the location of the surrounding resistors is different. This might or might not have consequences for the validity of the pinout as above. (Anyone: more information on the A1 rev.?)
 +Rev A1 is the same pinout, smd resistors are already attached, just add header.
-===== OpenOCD ===== + 
-==== openocd.cfg ====+ 
 +===== JTAG Interface scheme for DNS-323 with the Wiggler port===== 
 +See the attached pinout: 
 +{{:hardware:dns-323-jtag.png}} 
 + 
 + 
 + 
 +==== openocd configuration file for the Wiggler method ==== 
 + 
 +openocd.cfg
<code> <code>
cat openocd.cfg cat openocd.cfg
Line 58: Line 71:
jtag_ntrst_delay 1200 jtag_ntrst_delay 1200
-#target configuration +#target <type> <endianness> <chainpos> <variant> 
-daemon_startup reset +target feroceon little 0
- +
-#target <type> <endianness> <startup mode> <chainpos> <variant> +
-target feroceon little run_and_halt 0 +
-run_and_halt_time 0 500 +
# planing with flash code - work in progress # planing with flash code - work in progress
Line 70: Line 79:
#          driver  addr      size    chip_width  bus_width  options #          driver  addr      size    chip_width  bus_width  options
flash bank cfi      0xff800000 0x400000 1          2          0 flash bank cfi      0xff800000 0x400000 1          2          0
 +
 +#target configuration
 +init
 +reset run
 +sleep 500
 +halt
</code> </code>
 +
 +
 +===== JTAG Interface scheme for DNS-323 with the Amontec JTAGKey Tiny  =====
 +[[http://www.amontec.com/jtagkey-tiny.shtml| JTAGKey Tiny]]
 +
 +Solder 47 KOhm resistors @  R202 R201 R200
 +Connect JTAG pins just like the Wiggler port, and also bridge R199 (EN pin to VCC) to enable JTAG.
 +Refer to the top half of the pdf as attached in the previous section.
 +Pinout of the jtagkey tiny is available [[http://www.amontec.com/jtag_pinout.shtml| here]]
 +
 +==== openocd configuration file for the Amontec JTAGKey Tiny ====
 +
 +openocd.cfg
 +<code>
 +telnet_port 4444
 +gdb_port 3333
 +
 +interface ft2232
 +ft2232_device_desc "Amontec JTAGkey"
 +ft2232_layout jtagkey
 +ft2232_vid_pid 0x0403 0xcff8
 +jtag_speed 3
 +
 +reset_config srst_only
 +jtag_device 4 0x1 0xf 0xe
 +
 +jtag_nsrst_delay 1200
 +jtag_ntrst_delay 1200
 +
 +#target <type> <endianness> <chainpos> <variant>
 +target feroceon little 0
 +
 +# planing with flash code - work in progress
 +#working_area 0 0x00400000 0x40000 nobackup
 +
 +#          driver  addr      size    chip_width  bus_width  options
 +flash bank cfi      0xff800000 0x800000 1          2          0
 +
 +#target configuration
 +init
 +reset run
 +sleep 500
 +halt
 +
 +</code>
 +
 +
 +===== OpenOCD =====
 +
==== Running OpenOCD ==== ==== Running OpenOCD ====
Line 107: Line 171:
</code> </code>
-===== TODO ======+===== TODO =====
  * The flash code in OPENOCD does not understand CFI mode 2 access. However this looks to be easy to fix. There is an early patch that attempted to address this but was never added into the project release. This code provides a good starting point.   * The flash code in OPENOCD does not understand CFI mode 2 access. However this looks to be easy to fix. There is an early patch that attempted to address this but was never added into the project release. This code provides a good starting point.
===== Links ===== ===== Links =====
-  * [[http://forum.dsmg600.info/t250-DNS323-JTAG-Pinout-interface-details.html|Forum thread]]+  * [[http://dns323.kood.org/forum/t250-DNS323-JTAG-Pinout-interface-details.html|Forum thread]]

Navigation

Personal Tools